The quiet, 220-volt motors in these saws cut through the hardest stock, hour after hour, without bogging down. Cabinets are metal and extend to the floor for the best dust collection. The tops are cast iron, wide, and stable, which makes it easy to cut sheet goods. The trunnions are cabinet-mounted, so you get minimal vibration and maximum accuracy. They're also heavy; some weigh over 600 pounds. Once a cabinet saw's in place, that's where it stays.

The Porter-Cable looks like a beefed-up version of the Craftsman, with the same blade guard and anti-kickback pawls. This is the only saw in our test with a blade-tilting handwheel, which makes it easier to dial in a precise bevel angle. The motor mount and blade controls on this saw are very sturdy, without much play, which translates to a good-quality cut. Extending the fence for a wide rip requires a bit of effort on this saw, since the rails are stiff. All in all, this is a great saw for the price.


To provide the ultimate vibration control and stability, the entire cabinet rests on the heaviest cast iron base in the industry, and all steel cabinet components and the cast iron table top are factory fitted to prevent slippage and rattle. Speaking of the table top, the capacious workspace makes shaping and fitting even the longest workpieces quick and easy thanks to its rock-solid support. Dust collection is accomplished via the blade shroud below the table, and can be connected directly to a shop vac thanks to the standard 4-inch diameter power in the rear section of the cabinet.
SawStop has an excellent stand and they’ve cleverly hidden the tool/miter/riving knife storage box under the side extension. Move the table extension and the box presents itself. Like DeWalt, two riving knives come with the saw—one with safety guards and one without. This keeps you from wondering how the pawls and guard go on the riving knife. Blade height fully adjusts with only one turn of the wheel. Not everyone was on board with this, citing less accuracy for dado and rabbet cuts. In the end, we showed we could be as accurate on the height as any of the other saws, so it’s a win.
The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.
So what should you do? The good news is, you don’t need to rely on budget tools to get you through your projects anymore. All you need to do is set aside some time to do some research and investigating so you can find a tool that truly fits your needs. And luckily for you, we’ve taken the time to compile a list of the top 10 best table saws that you can invest in for your woodworking projects.
For some table saws, a dust collection system is just a bag that collects the dust generated from your table saw. This might do the job perfectly well for many novice table saw users, whilst others might benefit from a more sophisticated dust collection system. Either way, it’s of paramount importance to make sure that you pick up any dust generated by your table saw, as it could be dangerous in the long term to both you and your family.

When it comes to the type of wood that you can cut through with a cabinet table saw, you can purchase one in confidence of the fact that you’ll be able to cut just about any type of wood. That being said, as a general rule, you’ll find that the more expensive cabinet table saws offer great strength and flexibility. However, in terms of the pricing of table saws, you’ll definitely find that they can become pretty expensive. This is no surprise though really, especially when you take into consideration the fact that cabinet table saws are designed solely to be used within a professional environment.


Powerful cutting and portable convenience with the Delta Powerful cutting and portable convenience with the Delta 36-6022. The 1-step release stand and large wheels make it easy to move the saw to any jobsite. The 15 Amp commercial grade motor cuts through the toughest materials. UL approved 3-way guarding system with riving knife for safety and excellent dust ...  More + Product Details Close
No matter what you need a table saw for, the three listed above are great choices to consider when you’re doing your shopping around. Whether you’re a professional contractor or a serious DIYer, any one of them will have all the features, power, and portability that you could want in a table saw. All of the ones listed here, and most others have warranties and 30-60 day money back guarantees to give you a chance to see if you like them so your purchase won’t be a waste if you don’t, you will be able to get your money back, but we’re pretty sure that if you choose one of the three that we have detailed for you, you’re going to be able to join the many, many customers who are very happy with their purchases.

Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.
From flexible plywood sheets that move on their own to thick wood boards, this Jet 708677PK XACTASAW Deluxe 5HP Cabinet Saw can help you cut through all types of wood. This saw comes with a riving knife that reduces the risk of binding and kickbacks and has a quick release design to let you use it anytime you need. A left tilt trunnion makes pushing boards and sheets through easier while also giving you the stability that you might need.
However, with proper use, table saws are generally safe tools, advanced blade stopping technology not needed. Therefore considering a saw without such safety features is fine for the cautious DIY user or for the professional carpenter and/or builder. Take into careful account the actual table size of the table saw you are considering. If you are going to be completing rip cuts in large sheets of plywood, then you need a saw with a table large enough to support these big pieces of lumber.
The blades are the primary factor to consider when shopping for a saw as they hugely determine the performance of your table saw. The blades will only be effective if they are set at a correct depth of cut. The table saw will also perform best if only the correct blade for the cut is fitted, as a proper blade will enable you to achieve a precise and smooth cut. When purchasing a blade, go for the one with a correct setting blade. Consider the cutting depth also as this will determine its suitability for the job. You should also ensure that the table saw is equipped with splinter guard as this will help in minimizing splintering of the board’s top surface. Splinter guard also enhances accuracy because when it is lined up at the start and finish mark the saw will cut with precision. A suitable table saw should also have a 20mm arbor as this guarantees the stability of the blade and hence, safety in the workplace.
Paul – Good catch….I’ve updated that to say Skilsaw not SawStop…thank you! As you can imagine…all the data makes it tough to keep it all straight. I’m not even sure how you’d install that aftermarket fence on these saws. If you do I’d love to see how!! Those really look like they are made to install on cast-iron full size saws. I’d choose the DEWALT with a slight edge over the SKilsaw.
The table itself is made of heavy cast iron, as are the control wheels for blade depth and angle on the front of the cabinet itself. Unlike many cabinet saws in its class, the G0690 provides up to a 90 degree left tilt bevel, and both blade height and angle can be locked into place for easily repeatable cuts. Better still, the fence is constructed from heavy duty steel, and is cam-locking to keep it stable regardless of vibration or weight of the workpiece.

Another important safety feature to consider is a magnetic switch. Magnetic switches are there in case of power cuts or outages and will also protect the table saw motor from over load. Effectively it will switch off the power supply the instant the power goes off ensuring you don’t have a saw blade spinning away in the dark! As you can imagine this is a very useful and must have safety feature when looking to purchase a new table saw.


15 Amp Motor – If there’s one thing that you’ll learn from this website’s table saw reviews, it’s than I order to for a table saw to be effective, it needs to be pretty powerful. With an included 15 amp motor, we can quite comfortably say that this particular product meets that specification. In fact, you should find that the motor is able to easily rip through hardwoods and just about any other type of wood.
Should work on any saw that has at least 3/16" of clearance between the LED and the saw carriage. Sorry but the SAW IS NOT INCLUDED. Each LED lamp assembly is precision machined and proudly made in Texas by an old retired veteran who knows what works because he made it for himself first and then decided to share it with others who are looking for the optimal solution at a great price.
The Craftsman table saw is one of the most compact of the bunch when it’s folded up. And if you can get it for the sale price of $260, it’s also the cheapest of the best table saw options. The blade guard and anti-kickback pawls are identical to the Porter-Cable and are the hardest of any of the saws to install. And they are the only two blade guards that don’t have a feature to hold them out of the way when you’re adjusting the blade or setting up the cut.
If you’re a DIY enthusiast, you’ll definitely find something of interest. On the other hand, professionals can also find good pieces of information on this page. The models we’ve covered all work as advertised, and you can rest assured that they are of high quality. The only thing you need to do is determine how much money you want to spend and which type is the best suiting one for your requirements.

Lightweight: Typically, you want to choose a portable table saw that is relatively lightweight but sturdy. This will make sure that you are able to work faster and more efficiently compared to heavier options. It also cuts down the strain involved in using this tool as well in moving from one location to another. While looking for lightweight options, do not compromise on the stability element though. If your table saw is not sturdy, it can easily be wobbly while cutting the wood or other material. This is a safety risk but also will end up with junk projects and mistakes. Woodworking is all about precision, and that requires stability.
These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.

I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.
×