With a cutting speed of at least 4,500 RPM, nothing will hold you back from getting the job done in minutes. Hitachi job site table saw is designed to give you freedom in your work and the ability to manage your time. Keep every minute accountable by investing in the right tools for your workshop. However, during different occasions, you will have different materials both in size and texture. During such moments, you will require adjusting the fence to accommodate your material and cutting style. This job site table saw is designed with an adjustable feature to ensure your precision and accuracy is not compromised. The low power consumption makes it easy for you to maintain the saw and enjoy smooth and accurate results at no extra cost. When it’s not in use, the table saw has fold and roll stand that guarantees you space saving and convenient storage. The foldable design also makes it easy to transport from one place to the other comfortably.
The stand is collapsible and wheeled like others, but it’s not the gravity-rise style. You’ll have to use a foot to stabilize it while you pivot it up or lower it down. The lower locks are released with your feet and there’s some question about the long term durability of the releases. An open housing design has two major results – motor cooling should be more efficient but it trades off storage for an extra blade. There’s really way too much to talk about here, so check out our full review of this model.
A 50 rpm deviation at those speeds is approximately 1% variance which is well within the tolerance we should expect from taking the readings at a precise instant of time. The meters were in constant motion and we took the reading off of a single video frame that represented our determination of no-load speeds. We report them as our instruments showed them. 1% is acceptable.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
Buying a table saw can cover a lot of bases. You have everything from DIY models to professional production level cabinet table saws. In this article, we’re looking what is arguably the most popular – jobsite table saws. They’re on the less expensive side and are highly portable compared to their shop counterparts. That makes them go-to tools for framers, jobsite carpenters, and Prosumers.
How do you tell what the best table saw is? With so many table saw choices on the market, it’s hard to know which table saw is the best fit for you and your woodworking needs. Not for long. We’ve taken the leg work out by doing all the measuring, tracking, and researching for you. We’ve compiled year-over-year performance and pricing information for over 3 years to help you choose the table saw that is ideal for you and your project. Search no more, find your table saw below.
Under the table, you’ll find plenty of space to store away your accessories. This is valuable if you’re working on site and don’t want to keep hunting down bits and pieces. You’ll be able to stash your arbor wrench and Allen wrenches close to hand. The rip fence also flips upside down and can be stored under the table. It’s this kind of attention to detail for a jobsite saw that’s always appreciated.

Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.
Every woodworker knows the plague of working in a dusty environment. The SawStop has a fantastic dust collection system so you can enjoy your cutting without your eyes being strained. Almost all of the dust is wicked away both above and below the table. Up above, the blade does all the legwork and there’s a neatly designed shroud which pulls all this dust away from the blade. The 4-inch port means you can slip your shop vac on with no issues.        
This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.

Looking to purchase a portable saw for your DIY projects? Are you interested in funding some quality tool to cut large pieces of wood properly? Then, take a look at this incredible model. When buying this kind of tool is very important to understand several things including its capabilities. When it comes to accurate cuts and quiet operation, the DEWALT DW745 could be exactly what you are looking for. It is a popular model that comes with a lot of impressive features. It comes equipped with a Pro Modular Guarding System for increased accuracy. It is powered by a powerful 15 amp motor and it has a large 20-inch rip capacity. Thanks to its powerful motor, it delivers a no-load speed of 3850 rpm. Also, it should be noted that it uses blade guards. Plus, it comes equipped with a miter gauge, a push stick and a dependable 10-inch, 24-tooth carbide blade. The DW745 is covered by a 3-year limited warranty and 90-day money-back warranty. In addition to this, there is 1-year free service.


I just purchased this saw last week. It took several hours to assemble. everything was there and I had no problems putting it together. Not hard but time consuming. The first job was to rework some vertical drawers. It did a good job fence worked great as did the riving knife. Saw was quitter than I expected. overall I am very happy. The only problem was that I had to weight a couple of extra days for delivery due to all parts not arriving at the same time.

The miter gauges on these saws range from downright flimsy to cabinet-saw quality. All the saws except the Craftsman and the DeWalt also have T-tracks—a nice feature that captures the miter gauge bar, making it easier to start wider crosscuts. Because the Ryobi and DeWalt saws don’t have a standard miter gauge slot, you can’t use accessories that require a 3/4-in. slot.
When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.
Electric brakes in the saw is an important feature as helps the saw in reversing electricity in the motor, thus contributing to a precise cut. It is highly recommended that when you are buying a saw choose the one with on and off switch. The switch should be easily accessible to make work better and more efficient. In addition, the switch should have a cover. This will keep you from accidentally turning the saw on and damaging your work area or cutting yourself.
I just purchased this saw last week. It took several hours to assemble. everything was there and I had no problems putting it together. Not hard but time consuming. The first job was to rework some vertical drawers. It did a good job fence worked great as did the riving knife. Saw was quitter than I expected. overall I am very happy. The only problem was that I had to weight a couple of extra days for delivery due to all parts not arriving at the same time.
Bosch GTS1031 10 in. portable jobsite table saw is powered by a 15 Amp motor that allows this table saw to rip through any lumber or hardwood quickly and easily. Bosch’s Smart Guard System provides added control while cutting, SquareLock Rip fence ensure consistent and accurate cuts, and an all-steel base provides added durability. Oh yeah, and we forgot to mention the price. This is the most affordable table saw on our list!
Smoothness & Accuracy: This is another important factor to be aware of. You need to make sure that you decide on a portable table saw with a blade that can cut any type of wood easily. The fence needs to be able to fix the wood securely, and a miter gauge adds to the overall accuracy element. It also significantly adds to the range of options you can use the table saw for.
Once again our team has put some serious time and effort into our Head-to-Head evaluation to bring you the most comprehensive information available. For this evaluation, we broke things into several categories including: Precision & Accuracy, Performance (power), Price, and Ergonomics. For each of these categories we’ll rank the saws and at the end we’ll name the Best Portable Jobsite Table Saw based on all the results combined.
The accuracy and safety of any given saw is dependent upon the blade being parallel to the rip fence. Since we tested the amount of difference in parallelism between the saw blade and the miter slot in the previous test, we need only to see if the miter slot is parallel to the rip fence to see if the saw has a parallel relationship between the blade and the rip fence.
If you spend a lot of time working with wood in your garage or workshop, you know the importance of having the best table saw on the market. Many craftsmen find that they feel connected to their work, and because of this they need tools that will work efficiently and reliably. If you’re invested in the art of carpentry, woodcarving, or any other wood related trade, you know that you need a machine that can work efficiently without overwhelming your budget.
You will not always get your job within the workshop, there are moments where you will have to get out and work from a distant place. Therefore, you will require having a table saw that is portable and reliable for such duties. Rockwell table saw with a laser has large legs with wheels. You can easily pull it to any place comfortable as the wheels keep rolling. In other words, you will not have to struggle with the entire unit trying to lift it when you want to switch working positions. Additionally, this table saw has a foldable fence for convenient storage and also ensures there is enough room for all size material. The inclusive laser guide is to ensure you get consistency in accuracy. Once the blade is not in the position, the laser guide adjusts automatically for the benefit of the user.
Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.
Every woodworker needs a tool to make furniture and build cabinets. The wood cabinets are vital in any building because they increase the storage capacity of any room. Whether small or big, a cabinet should be done only with a quality model. This powerful tool is capable of cutting big pieces of wood into different sizes and shapes for building cabinets and making furniture.
The 708494K JPS-10TS from Jet Proshop is a high end cabinet table saw which delivers on all your expectations. Available in either a thirty inch or a fifty two inch rip capacity, this model is built from cast iron and is extremely rugged in order to withstand a lot of abuse and still deliver the excellent results you’re expecting from it. Regardless if you’re a professional or if this is the first cabinet table saw you’re planning to get, the 708494K JPS-10TS won’t disappoint. Its rugged build quality and ease of use are going to make it one of the best table saws currently available.
Love the video. It was very helpful, answered some of the questions I've had and wondered if you can expand this a bit further. I have a Thomasville bedroom set that I bought in 1981. After all of the years of my wife using hairspray, there's a layer of it on the bed's foot board and the top and leading edge of the dresser. Will this technique remove the hair spray and restore the finish? I tried using denatured alcohol to clean it in the past but stopped short of using a sanding pad or working it to the point that nit was anything but tacky. Sounds like I didn't work it long enough. Am I right or do I need to do something else? These areas are the only bad spots on any of the 5 pieces of the set. Thanks!
×