Contractors who do a lot of finishing work and interior/exterior trim work know the value of a good portable table saw. DeWalt has built the DWE7490X from the ground up as a stable and safe job site cabinet saw that can be used to make those precision cuts quickly and easily without the need to pre-fabricate materials and then bring them to the job site for final fitting.
The SawStop PCS31230-TGP252 Professional Table Cabinet Saw is our premium choice pick for a reason - it’s one of the best cabinet saws on the market. You’ll be able to tackle nearly anything you can think of with this impressive tool and work like you’d never be able to imagine. The saw is powered by a 13 amp motor that has a 220-volt requirement and saws through material quickly and efficiently. It’s a carpenter’s dream and was built with all of the needs of the craftsman in mind.
The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.
The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.
Safety is at a pretty high level, to say the least. There are a few integrated mechanisms that prevent accidents from happening, but that doesn’t mean you shouldn’t handle it with care. Also, don’t forget to wear safety equipment at all times. Whether you’re a professional or a beginner, you’ll definitely like this particular model due to its versatility and a wide array of potential.
The biggest advantage of hybrid saws is the fact that they can be plugged in a regular 110V/220V outlet. Therefore, you don’t need any additional power sources in order to use these units. It quite a relief because you’ll avoid any further investments. These saws are quite easy to use if you know what you are doing. However, if you don’t, remember to read the manual before turning your saw on. It will save you a lot of hassle and also keep you safe.
We went through a large number of portable table saw reviews to help you identify the top options that you could choose from. If you do not have the time to surf through hundreds of options available online, this list will make the task easier for you. Of course, you can also use our buying guide to sift through options outside this list. In saying that, let’s get started with our top pick, the DEWALT DWE7491RS!

These tools can be classified into three types, such as the compact, bench top and job site saw. As compared to the stationary models they are smaller and more lightweight. Furthermore, the heavier materials used in their construction are seriously reduced to keep their weight down. Most units are equipped with a 15 amp 120V motor which delivers no more than 2 hp. As it was mentioned before, the size matters and it is an important factor to consider when purchasing a woodworking machine.
How do you tell what the best table saw is? With so many table saw choices on the market, it’s hard to know which table saw is the best fit for you and your woodworking needs. Not for long. We’ve taken the leg work out by doing all the measuring, tracking, and researching for you. We’ve compiled year-over-year performance and pricing information for over 3 years to help you choose the table saw that is ideal for you and your project. Search no more, find your table saw below.
The miter gauges on these saws range from downright flimsy to cabinet-saw quality. All the saws except the Craftsman and the DeWalt also have T-tracks—a nice feature that captures the miter gauge bar, making it easier to start wider crosscuts. Because the Ryobi and DeWalt saws don’t have a standard miter gauge slot, you can’t use accessories that require a 3/4-in. slot.
User reviews at Amazon and Home Depot are also very positive, with about 4.6 stars overall from more than 900 owners. Multiple users say the saw cuts through wood "like butter," and they praise its easy setup, accurate rack-and-pinion fence, and easy-to-use stand. The one feature users dislike is the miter gauge, which many reviewers describe as flimsy. We also saw a few more general complaints about poor quality control on this saw. Users report problems such as warped tables and slots that don't align, making it impossible to calibrate the saw properly. Fortunately, if you happen to get a lemon, you can replace it under DeWalt's 3-year warranty, which bests Bosch's by 2 years.
In most situations, you can take the dust bag off of the port and hook up a shop vac or an industrial dust-collection system. Many table saws make use of a standard-size dust port between 2-1/2 and 4 inches in diameter, which means it may be compatible with equipment that you already own. Some models forgo the dust bag altogether, in the expectation that you’ll be using some sort of dust collection system.
Changing a table saw blade may seem daunting, but it’s actually fairly simple and straightforward. You just need to keep a few safety precautions in mind and have the right tools You’ll need to start by making sure your table saw is off. Unplug the device and make sure that when you press the ‘on’ button the blade doesn’t spin. Now that you’re certain the area is safe, it’s time to start. You’ll want to find a screwdriver set and the spanners that came with your table saw before you get going.
The good news is that if you already own a dust collection system or a shop vac, then you may be compatible with many models. Even if it doesn’t match the port size of your shop vac, you can often purchase converters that will make the table saw work with the system you already own. Consequently, you shouldn’t avoid a unit because it has a port size that is different from the gauge of your shop vac. This is something to look into before making a purchase, just to make sure that converters that will work with your model are being sold.
Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.
Every woodworker needs a tool to make furniture and build cabinets. The wood cabinets are vital in any building because they increase the storage capacity of any room. Whether small or big, a cabinet should be done only with a quality model. This powerful tool is capable of cutting big pieces of wood into different sizes and shapes for building cabinets and making furniture.

We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
Another good table saw from Powermatic is its 1792006K Model PM2000 5 HP 3-Phase Table Saw with 50-Inch Accu-Fence System and Rout-R-Lift. The dust collection port moves much of the debris you produce away from your work area, but the cabinet itself has a sloped design that makes it easier to get under the cabinet cleaning. Its quick release riving knife not only reduces kickbacks but also reduces the risk of the knife binding.
For carpentry projects or as a starter saw, the DeWalt DW745 receives solid reviews. Though it doesn't have the capacity of the Bosch, owners say it's well made and easy to adjust. The rack-and-pinion fence earns kudos for accuracy. The saw weighs just 45 pounds and can even be hung on a workshop wall for storage; an optional is also available. The three-year warranty is another plus.
When considering the type of saw you need for your projects, think about the type of work you want it to do, how much time will be used, the amount of money you want to spend and how much room you will have in your shop for it. If you are only a weekend woodworker and only work an hour or so each time you use it while doing small craft projects the cabinet saw may be a perfect option for you. However, if you own a small woodworking shop and will be working many hours every day with the saw the hybrid would probably be more suited. Before purchasing a saw for your needs, research by reading other consumer table saw reviews to give you the best options.

Best of all, the XACTASAW Deluxe features a left tilting blade design, an industrial grade 50-inch commercial t-square fence, and an integrated miter gauge for making ultra-precise cuts on the toughest of woodworking materials. No matter the complexity of your woodworking project, this cabinet saw has you covered. This is definitely a world class tool for world class craftsmen, and it is an ideal addition to any woodworking shop whether you are starting out or you’ve been on the job for years.
The Shop Fox W1819 also comes with a miter fence with flip stop which provides excellent workpiece support and is great for longer workpieces. As for the flip stop, it’s going to be very useful especially when wanting to make several cuts of the same width. If you want to cut longer workpieces, you can also flip it out of the way and then pivot it back down in order to make more cuts at the cutting width of your choice.
Methods for tilting the blade to cut bevels vary among the saws. The Porter-Cable saw is the only one with a conventional handwheel bevel control mounted on the side of the saw. The crank gives you great control for setting an exact angle. To set the bevel on the Bosch, DeWalt and Rockwell saws, you simply release the bevel-lock lever and tilt the saw to the preferred angle. It’s easy to go quickly from a 90-degree to a 45-degree bevel with this method. The Ridgid, Craftsman and Ryobi saws have a rack-and-pinion setup. These saws utilize the front crank for setting the bevel.
The bench top saws have a compact yet ergonomic design. Thanks to their lightweight feature, more and more people prefer to use them in their workshops. Despite the fact that they are not equipped with wheels, they can be considered portable, because they are very small. As such, they can easily be carried and transported from a place to another by almost anyone. Also, in comparison to the jobsite saws, the benchtop saws have a very limited rip capacity.
That said, I have been looking for that ideal replacement saw that will hopefully take me further down the road than the Craftsmen, and a unit that will do what I need it to do. This review could not have been found at a better time. I will take the results that were achieved and use them as a measurement in purchasing a new one. Thanks for the time spent on conducting this testing and review. Very much appreciated!
Some table saws come with a miter gauge, though the quality tends to be uneven. Some are great, and will serve you well for a long time, while others are flimsy or struggle to hold the correct angle or both. This is something that can most easily be determined by reading online reviews, though it’s always great to get your hands on a demonstration model, if possible.
It’s interesting to note that if pricing was taken out of this evaluation the ranking would have been: DEWALT in first, Makita in second, Hitachi, Skilsaw and SawStop tied for third, Bosch in fourth, Delta in fifth and Ridgid in sixth place. But at the end of the day price is certainly a factor. What we didn’t do in our evaluation is any long term testing to look at durability which ultimately could affect your purchase decision as well.
When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.
If you’re not sure how to proceed, it’s important to take a breath and think about what you need out of a table saw. You could get a model with every possible bell and whistle, but there’s there no reason to do that if you’re not going to use it frequently. Likewise, you could just buy the cheapest model, but that doesn’t mean it’s going to be a fun machine to use.

It has a brilliantly powerful 15 AMP motor, which can deliver 4,800 RPM of cutting power. Is is normally more than enough for most woodworkers and hobbyists. It has stowable anti-kickback pawls and and excellent riving knife and spreader for accurate cuts. This is a great entry level saw at a great price, definitely worth looking at for your next purchase or project.
As you would expect, the most expensive saws made slightly smoother cuts. But the difference was negligible. The only saw that struggled to make smooth cuts in the super-thick oak was the Ryobi. In more common situations, like cutting 3/4-in.-thick material, Ryobi’s cut quality was fine. We found the blades included with all the saws to be adequate for most ripping tasks. But if you want cuts smooth enough for glue joints, you’ll have to invest in a better blade.
×