Contractor models also tend to be more powerful and more precise than portable saws, which gives them a definite upside if you’re going to be doing lots of work, or work that requires a fine degree of precision. This type can also be a good choice if you’re going to leave your table saw in one place for extended periods of time, while still being light enough that they can be moved if you need to do so.
For any kind of professional woodworking and large scale construction work, the cabinet table saw is the one for the job. These types of table saws are often called stationary saws. The motor is protected in a cast iron and steel cabinet that reduces noise and vibration as well. With reduced vibration comes better accuracy which is always the desired effect, especially for professionals. The motor us a powerful 3-5 hp and requires a 220-volt outlet. If you are using it in a home workshop, a special outlet may need to be installed if 220s are not already installed in your garage or shop. Measuring about 28” x 43” and weighing in at over 400 pounds, these table saws were not designed to be portable. The large work surface is ideal for cutting large pieces with ease. Cabinet saws can use a 12” blade with no problem, although a 10” blade is the most commonly used. It is the most expensive of all of the styles of table saws.
When you need a full size cabinet saw that can handle just about any woodworking job you can throw at it, the Powermatic PM2000 is the one for you. As with all high end cabinet saws, the PM2000 features box-style cast iron trunnions for that refined, precise feel when adjusting the blade angle and height. Front control wheels are user-friendly cast iron hand wheels that feature precision-machined center locking pins for making every cut consistent and repeatable.
If you are a woodworking professional, you'll want a cabinet saw in your workshop. These are the heaviest, sturdiest and most precise table saws, with powerful motors that require a 220-volt electrical outlet. Cabinet saws require a large, dedicated space because of their guide rails and large tables (often with big extension wings). Then also tend to have the best safety and dust-control features. Woodworkers with enough space (and money) usually make a cabinet saw the permanent centerpiece of their workshop, though a few cabinet saws have mobile bases. Cabinet saws cost $1,600 and up.
Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.
Hybrid saws will often match in terms of power but very rarely have the stability and durability of a cabinet saw, so often they work well in a home work shop where you can add extra stands etc to help. One thing to think about though is that because they won’t be as stable this can often compromise on the quality of the cuts, this is something you must think about when deciding. Read More
The first step to take when using a table saw is to don all the appropriate safety gear that a responsible operator should use. This includes, at the bare minimum, eye protection and thick work gloves. It's also a good idea to protect your ears with ear muffs or earplugs and to consider a mask that will cover your mouth and nose to prevent the inhalation of fine saw dust particles.

Framing work is full of rougher cuts that rarely makes use of more than one blade at a time. But occasionally you might need dados for an onsite custom build in. If that sounds like you, be sure to find out the saw’s dado stack capacity. It requires a longer arbor and you won’t be able to use your normal throat plate for it. Some manufacturers offer a dado throat plate if they have the capacity for it.


Depending on how often you work with wood and the type of wood that you use, you may find that this SawStop PCS175-PFA30 1.75-HP Professional Cabinet Saw Assembly is better suited to your needs than some of the company’s more expensive models are. This saw features a smaller base and a shorter extension table that take up less space, but you can use the fencing system to extend the size of the table working with your boards.
Setup was nearly as simple as SawStop’s with just a narrow margin between them. We only needed to attach the handle and bolt the saw down to the stand. The stand is a gravity rise style, but requires you to bend down to ground level for collapsing and extending it. It’s a reasonably solid platform, though a lot of movement throughout the day will leave your back sore.

After reviewing several models we can truly say that metal components are more durable than plastic. Cast iron, for example, is a durable material that provides the most stable surface. It is capable of minimizing vibration and is much heavier than steel or aluminum. Every quality model has a smooth surface and sturdy legs that ensure stability. In what regards the motor and its components, you probably know that it’s quite difficult to check them by looking. However, any product should have a warranty and for a quality product, the manufacturer should offer at least a 3-year warranty.
Ergonomics is the science of designing and producing tools that improve a worker’s efficiency while reducing discomfort, fatigue, and risk of injury. Ergonomically enhanced tools can include helpful features such as angled handles, riving knives, safety switches, and non-slip coatings. Whether you’re shopping for ergonomic tools or just trying to select the right one for the job from an existing collection, the key things to consider are whether or not the tool eases your work and prevents you from straining in ways that could lead to injury. Ergonomic guidelines in tool design can help maximize human performance on the job by making the job easier for the worker, improving safety and decreasing injuries.
Table saw reviews take the guesswork, and considerable comparative research time-out of the buying equation. Table saw reviews are the result of consolidating the user feedback for the most effective and relevant input. After the data is analyzed, you receive the best of the best, in a condensed version. These streamlined recommendations enable you to spend less time trying to determine which table saw is ideal for your purposes, so that you have more time to use the one you do decide to buy.

I just purchased this saw last week. It took several hours to assemble. everything was there and I had no problems putting it together. Not hard but time consuming. The first job was to rework some vertical drawers. It did a good job fence worked great as did the riving knife. Saw was quitter than I expected. overall I am very happy. The only problem was that I had to weight a couple of extra days for delivery due to all parts not arriving at the same time.
Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.

I was hoping to see the JET in there. But glad you didn’t waste your time with it. I bought it a year and a half ago and it’s a piece of crap. It has not held up at all, I keep it in my construction trailer and it has its own cubby hole and is secured with straps. It has fallen apart. The fence has no adjustments and is off 1/4” front to back, From the factory. I have to spend so much time trying to adjust rip fence, and then I can’t turn my guys loose with it because they won’t take the time to adjust and check for accuracy. Just really disappointed in the product. I am waiting for the testing done on the cordless saws because I am upgrading.
TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
The market for table saws is one that’s incredibly varied and that’s something that you’ve likely already noticed from just one look at the different table saw types. Reading on into our table saw reviews and you’ll notice that there’s also a range of different brands offering table saw products. But which brand is best for you? With so many of them available, it’s hard to understand the difference and make a choice over the best brand for you.
The power transfer system is neatly done. The model features a serpentine belt which is quiet and smooth during operation. Therefore, the level of noise is satisfactory. Precision is something that makes this model worth checking out. Whether you’re a professional or a beginner, you’ll definitely appreciate the accuracy of this model. On the other hand, with great things come great responsibilities. Don’t forget to wear safety equipment!
The Delta 36-L552 is a professional grade table saw, built for highly demanding use. You can use it all day everyday and it won’t miss a beat. It’s extremely accurate and will always produce the straightest cuts possible. Because of the high price we would always recommend you really spend some time looking into reviews etc to make sure it’s definitely the right product for you.
Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. The Makita was given the best score of 1 as it was considerably quieter than the remaining. DEWALT and Delta were ranked worse with a score of 3, while the remaining were ranked as a 2.
When it comes to actually using your table saw, you’re going to want it to pack some serious punch in order to saw through materials. The power of most table saws is measured using the horsepower scale. With that in mind, you can likely imagine that products on the market vary in terms of their horsepower measurement. Undeniably, you can imagine that this horsepower will vary depending on the type of table saw that you opt with, how much you’re spending on the table saw and you might also find it to be the case that different brands have a different horsepower that they opt for in their products.
The first contractor saws were made to be portable so they could be taken to job sites. These are also lightweight and priced low enough that the handy homeowner can use them. When purchasing the contractor saw there, you will have to make a few concessions. The table is not made of the cast iron top and the extensions are usually made of stamped medal. It is not made as burly as more costly saws. The motor also hangs off the back, which makes it easier to remove when moving the saw to another job site. Bosch table saws are reported to be one of the best budget saws available.
Large Cutting Capacity – When you’re working as a professional, it goes without saying that you’re generally going to need to cut a number of different sizes of wood. From look at this product, it’s pretty clear that DEWALT definitely understand this. The table saw features a 32.5 rip capacity, which is designed to easily cut through a variety of different shelving and trim materials, whether they be large or small. It might not be the case that you instantly need the ability to cut larger materials, but it definitely couldn’t hurt to have the option.
It is safe to say that we live in a DIY era. Think about it. When was the last time you went on YouTube or anywhere else online and looked for something that tickled your fancy, a guide on how something is made or done, or maybe a tutorial. Indeed, we do it very often, so why should woodworking and home improvement be any different? With the prices of table saws constantly dipping and the insane number of choices on the market, you can get one for yourself and save thousands of dollars by doing things yourself instead of hiring contractors.
×