As you would expect, the most expensive saws made slightly smoother cuts. But the difference was negligible. The only saw that struggled to make smooth cuts in the super-thick oak was the Ryobi. In more common situations, like cutting 3/4-in.-thick material, Ryobi’s cut quality was fine. We found the blades included with all the saws to be adequate for most ripping tasks. But if you want cuts smooth enough for glue joints, you’ll have to invest in a better blade.
Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.

Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.


The fencing should be perfectly straight and parallel to the blade in order to maintain a safe environment and achieve the best results. As soon as the fencing is taken care of, turn your attention to the blade itself. Is it properly adjusted and sitting at a perfect 90 degree angle? If not, you could encounter some issues while trying to work. You’ll need to find an accurate measuring tool to make sure your table saw blade is resting at a perfect 90 degree angle if you want to see the best results.
DEWALT® table saws are available in both cordless and corded. Our portable table saws are compact for easy transportation between jobsites. They offer a rack and pinion fence system for fast, accurate fence adjustments. Our table saws are lightweight and feature a metal roll cage to ensure they can stand up to a rough jobsite. Tool-free guarding component adjustments make it faster and simpler to adjust as needed. Since the World’s First FLEXVOLT® cordless table saw was introduced, DEWALT has revolutionized the world of cordless construction tools. Every aspect of our table saws are designed to make your job easier.
A cabinet table saw is so named because it has an enclosed style base. This saw is the opposite of the contractor saw. Cabinet table saws are designed to be functional and lasting to meet the qualifications that are required by people who work with wood for a living. They are constructed to be more durable than contractor saws. Makita table saw offers many popular options at a very affordable price.
There are a lot of great table saws on the market, but we’d have to say the best is the DEWALT DW745 Compact Jobsite Table Saw. This design enables you to be flexible with where you set up shop as well as extremely efficient thanks to the innovative technology that was incorporated into the design. Additionally, it has a 15 amp motor and a 20-inch rip capacity that makes it more than capable of taking on any challenge you throw at it.

In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.


Another important element of every model is the fence. Without the fence, you cannot make a precise cut. The most common type of fence that you can find on these units is the T-square fence. However, before getting into that let’s go over the most important characteristics a quality fence must have. First of all, it is important to know the role of the fence. It allows for hassle-free adjustment both vertically and horizontally. Also, it must be placed on the rails firmly, so you don’t encounter resistance while moving it. However, if this happens you can apply wax. Now, let’s have a look at the T-square fence. It is so popular because it is easy to adjust and maneuver. More than that, it is extremely accurate.
It’s often overwhelming when looking for new power tools and products online. So many features, specs and brands etc to research and review. So, what should you look for when buying a new table saw? One thing we always mention is to make sure you read as many table saw reviews as you can before purchasing one, this will insure you have the best table saw for your requirements.
I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.
×