A lot of the modern table saws nowadays will have a dust collection port where you can hook up a vacuum or extraction system to it. We would always recommend that you purchase a table saw with a dust port, always check the size of the port to make sure it fits with either your vacuum or your extraction system, or you can always modify something to make them fit.
In recent years, there has been a cloud of controversy surrounding the inherent safety issues surrounding the table saw. SawStop developed a flesh detection technology that pulls the blade below the table surface 3 milliseconds after coming into contact with skin. It really created a new class of table saw that, as of June 1st, finally has some competition in the form of Bosch’s REAXX.
This table saw isn’t going to provide near vibration-free performance, and you have to be extra careful about kickback since the base is not as heavy or weighted like a standard cabinet saw. Provided you are careful and work slowly though, it is possible to replicate the precisions of a heavy duty cabinet saw on the job site using DeWalt’s innovative DWE7490X.
There are a lot of great table saws on the market, but we’d have to say the best is the DEWALT DW745 Compact Jobsite Table Saw. This design enables you to be flexible with where you set up shop as well as extremely efficient thanks to the innovative technology that was incorporated into the design. Additionally, it has a 15 amp motor and a 20-inch rip capacity that makes it more than capable of taking on any challenge you throw at it.

The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.
We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.

All table saws sold in the U.S. come with a riving knife, anti-kickback pawls, and a split blade guard. Because some cuts can’t be made with these safety features installed, they are removable. If you’re looking for a fun party game, see who of your uninitiated friends can install both correctly without a manual. While each one is different, their nature means you can use the saw without them installed. I’d be remiss if I didn’t tell you those cuts are more dangerous, so avoid it if you can.
This table saw isn’t going to provide near vibration-free performance, and you have to be extra careful about kickback since the base is not as heavy or weighted like a standard cabinet saw. Provided you are careful and work slowly though, it is possible to replicate the precisions of a heavy duty cabinet saw on the job site using DeWalt’s innovative DWE7490X.
The Delta 36-L552 is the right cabinet table saw for boat building cabinet making and also woodworking. It features a fifty two inch Biesemeyere fence, speedometer style scales and also dual crank (up-front) controls with locking cams. Taking a closer look at the inside of the Delta 36-L552, we find a powerful 5 HP motor rated at 220V which is perfect for cutting engineered products such as melamine, MDF, but also hardwoods.
Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.
Stands are one of those features where the ends really do justify the means. Some made us wish the manual writers would take a cue from Lego—just make the *@#$! things easy enough for a 7 year old to understand. That aside, SawStop set itself aside brilliantly, taking just 10 minutes to setup. All we had to do was install the wheels and two handles. Even the packaging is designed to make the process easier and the instructions were super-easy to understand. Makita was nearly as simple only requiring us to install the handle and bolt the saw to the stand.

Continuing our discussion into the power of table saws, there’s another key contributing factor to that power and that’s the blade size. You should find that this blade size determines what you’re able to cut through using your table saw and the thickness of the materials that you’re able to cut through. In all, if you’re looking for a good all round blade size that just works comfortably, you’ll find anything within the 12 inch range to do the job. In fact, most table saws that we’ve seen for commercial sale feature this blade size.
When using the side extension, a tape moves along so you won’t have to remember what measurement to lock the fence on or read a double marked measurement guide. It’s an innovation we like, but there are questions as to the long term durability of the tape itself. Like Ryobi, Ridgid uses a magnetic throat plate to secure it while leaving access simple.
TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
Bosch GTS1031 10 in. portable jobsite table saw is powered by a 15 Amp motor that allows this table saw to rip through any lumber or hardwood quickly and easily. Bosch’s Smart Guard System provides added control while cutting, SquareLock Rip fence ensure consistent and accurate cuts, and an all-steel base provides added durability. Oh yeah, and we forgot to mention the price. This is the most affordable table saw on our list!

One of the biggest issues and potential hazards when working with table saws is kickback. Table saw kickback occurs when wood is ejected from the saw at extremely high speed. You can imagine the sort of injuries this can cause. Table splitters are effectively small vertical bits of metal or sometimes plastic that are designed to stop the wood flying back if there is a kickback.  Attached to the splitter are anti kickback pawls either side, they look like table saw blades themselves but they are in fact there to grip the wood at stick into it in case of kickback.
Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. The Makita was given the best score of 1 as it was considerably quieter than the remaining. DEWALT and Delta were ranked worse with a score of 3, while the remaining were ranked as a 2.
There are a lot of great table saws on the market, but we’d have to say the best is the DEWALT DW745 Compact Jobsite Table Saw. This design enables you to be flexible with where you set up shop as well as extremely efficient thanks to the innovative technology that was incorporated into the design. Additionally, it has a 15 amp motor and a 20-inch rip capacity that makes it more than capable of taking on any challenge you throw at it.

If you are a woodworking professional, you'll want a cabinet saw in your workshop. These are the heaviest, sturdiest and most precise table saws, with powerful motors that require a 220-volt electrical outlet. Cabinet saws require a large, dedicated space because of their guide rails and large tables (often with big extension wings). Then also tend to have the best safety and dust-control features. Woodworkers with enough space (and money) usually make a cabinet saw the permanent centerpiece of their workshop, though a few cabinet saws have mobile bases. Cabinet saws cost $1,600 and up.
Contractors who do a lot of finishing work and interior/exterior trim work know the value of a good portable table saw. DeWalt has built the DWE7490X from the ground up as a stable and safe job site cabinet saw that can be used to make those precision cuts quickly and easily without the need to pre-fabricate materials and then bring them to the job site for final fitting.
At this point, you are wondering why this is not number 1. The problem is with all that power, precision, and all those great features; you can get only 18 inches of cut from it. This severely impacts the usability of the product. While it can still be used for some home based products, its use in a professional setup is fairly limited to smaller projects. It also only has a one year warranty which is pretty light.
Some table saws come with a miter gauge, though the quality tends to be uneven. Some are great, and will serve you well for a long time, while others are flimsy or struggle to hold the correct angle or both. This is something that can most easily be determined by reading online reviews, though it’s always great to get your hands on a demonstration model, if possible.
When considering the type of saw you need for your projects, think about the type of work you want it to do, how much time will be used, the amount of money you want to spend and how much room you will have in your shop for it. If you are only a weekend woodworker and only work an hour or so each time you use it while doing small craft projects the cabinet saw may be a perfect option for you. However, if you own a small woodworking shop and will be working many hours every day with the saw the hybrid would probably be more suited. Before purchasing a saw for your needs, research by reading other consumer table saw reviews to give you the best options.
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.

For the woodworker who constructs anything from decorative cabinets to handmade boats, the Delta 36-L552 Unisaw is the professional grade cabinet saw that can get the job done. Thanks to its single case trunnion design, the 36-L552 operates consistently with minimal vibration and maximum repeatability of every cut. :Large dual front cranks allow you to dial in your blade height and bevel quickly and easily.
The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.

This type requires a heavy-duty circuit because it’s driven by a powerful 3 to 5HP motor. The blade is driven by three parallel V-belts which ensure a smooth operation and an efficient transfer of energy. Needless to say, if you have big plans, you might want to consider investing in a high-quality cabinet saw. Prompted, it’s going to cost you a significant amount of money, but it pays out relatively quickly.
Continuing our discussion into the power of table saws, there’s another key contributing factor to that power and that’s the blade size. You should find that this blade size determines what you’re able to cut through using your table saw and the thickness of the materials that you’re able to cut through. In all, if you’re looking for a good all round blade size that just works comfortably, you’ll find anything within the 12 inch range to do the job. In fact, most table saws that we’ve seen for commercial sale feature this blade size.

The CNS175-TGP36 SawStop is a 10 in. contractor table saw with a 45-degree bevel and a rip capacity of 36.5 in. Other than that, we think this is a pretty cool table saw for a few different reasons. First, the price is about half of all other SawStop table saws, and we know money talks (actually, it yells)! Second, like all other SawStop table saws, it has the integrated flesh sensing technology, so you can be sure you’re going to keep all your digits. Also, it has some pretty impressive power; it’s powered by 15 A motor so you’ll be able to tackle whatever you need. The last of our favorite features is its portability. For being a contractor saw, it’s pretty easy to pack up and move around.


If you are making a cut that will require your hands to get close to the blade, (within 6 inches) use a push stick or two to eliminate the chances of your hand touching the blade. If this is a big concern for you, maybe consider a saw that uses flesh detection to stop the blade. The additional cost of the saw will be instantly appreciated the first time you need it.
At this point, you are wondering why this is not number 1. The problem is with all that power, precision, and all those great features; you can get only 18 inches of cut from it. This severely impacts the usability of the product. While it can still be used for some home based products, its use in a professional setup is fairly limited to smaller projects. It also only has a one year warranty which is pretty light.

The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25" ripping capacity, meaning tearing through thick sheets of plywood has never been easier.
The simplest way to find out what size your table saw needs or indeed if you’re buying a special size is to consult the table saw user Manuel. I would make sure you do this as often there are many things in modern tables saws that could affect the blade size and type. This is because modern saws have many different amazing and varied features, things size blade guards, special safety mechanisms and arbor sizes etc. With the We recommend you spend some time reading your manual in detail to avoid possible issues
If you’re looking for one of the most powerful products on the market, you’ll find those such options within the 3-5 horsepower range. As you can likely imagine, these are products largely targeted at professionals looking to use their table saw on a day to day basis. If you’re a hobbyist or occasional contractor who doesn’t necessarily want to shell out a fortune on a table saw, you should find that between 1-2 horsepower does the job.
The Bosch 4100-09 10 Inch Table Saw is an expert tool that will be sure to impress its users with the reliable design and easy to use set up system. Our favorite feature was the gravity rise design that allows you to push the device around easily and focus more on getting the job done instead of wasting time trying to set up a complicated device. The tool is also coated in a powder coat that helps to improve the longevity of the device and features a collapsible design that is easy to fold up and down once you get to the job site.
We made a few test cuts with ¾-inch plywood just to get a feel of the motors we were working with. It became clear pretty quickly that not all 15 amp motors are equal. Once we knew what to expect, we moved to pressure treated 2x pine material in 7-1/2 foot lengths. Why 7-1/2? Our test material started at 15 feet and it seemed silly to have some at 8 feet and others at 6.
This table saw isn’t going to provide near vibration-free performance, and you have to be extra careful about kickback since the base is not as heavy or weighted like a standard cabinet saw. Provided you are careful and work slowly though, it is possible to replicate the precisions of a heavy duty cabinet saw on the job site using DeWalt’s innovative DWE7490X.
Furthermore, the split guard offers a tool-free riving knife that moves freely via a front level control for on-the-fly adjustment. Pawls and splitter guards can also be added to the riving knife without the need for tools as well. Best of all, the 36-L352 includes a 52-inch Biesemeyer Fence System that has an integrated tape and a hairline pointer for consistent and repeatable cuts every time. If you don’t work with wood that needs the additional horsepower of 36-L552, this version of the Delta UniSaw is definitely for you.
With a quick release riving knife, this Jet 708676PK XACTASAW Deluxe 5HP with 30 In. Rip Fence reduces the risk of binding and also cuts back on the kickbacks that you might otherwise feel. Its five-horsepower motor is one of the most powerful on the market and can make quick cuts in any type of wood. It also comes with a 30-inch rip fence making rip cuts, though you may find that this fence is a little too short your needs.
As the name indicates, it has a V-belt and a pulley system through which the power is transferred. Given the much higher torque and power, these drives are more suited for heavy-duty sawing jobs, providing better efficiency when cutting thicker wood variants. Additionally, a belt drive throws up much less dust as the motors are mounted far away from the blade. I would say other than that; they are less safe and more costly.
To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.
It’s interesting to note that if pricing was taken out of this evaluation the ranking would have been: DEWALT in first, Makita in second, Hitachi, Skilsaw and SawStop tied for third, Bosch in fourth, Delta in fifth and Ridgid in sixth place. But at the end of the day price is certainly a factor. What we didn’t do in our evaluation is any long term testing to look at durability which ultimately could affect your purchase decision as well.
Framing work is full of rougher cuts that rarely makes use of more than one blade at a time. But occasionally you might need dados for an onsite custom build in. If that sounds like you, be sure to find out the saw’s dado stack capacity. It requires a longer arbor and you won’t be able to use your normal throat plate for it. Some manufacturers offer a dado throat plate if they have the capacity for it.

No doubts about it, a table saw is one of the most important tools a woodworker can have in its garage. There are dozens of models on the market and after reviewing a lot of them we can say that it is more than complicated to take the right decision. Therefore, if you are looking at buying a quality machine, but you have no idea about their features, construction, design and so on, below is a comparison table specially made for people like you. In this comparison chart, you will find detailed information about the best models in 2018.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
×