Some table saws come with a miter gauge, though the quality tends to be uneven. Some are great, and will serve you well for a long time, while others are flimsy or struggle to hold the correct angle or both. This is something that can most easily be determined by reading online reviews, though it’s always great to get your hands on a demonstration model, if possible.
We love the  DEWALT DWE749RS 10 Inch Table Saw for it’s great design and easy function . The machine is fairly easy to transport from jobsite to jobsite and we’ve found it to be one of the best portable table saws available to contractors today. The  DEWALT DWE749RS 10 Inch Table Saw helps to keep workspace clean and efficient by incorporating a 2 inch dust collection port into its design. The dust collection port also has a vacuum connection port so you’ll easily be able to suction out all of the dust that comes off the machine blade while you’re hard at work.
Below we’ve included the current pricing (at the time of publishing this article). Pricing includes the cost of the stand and ranges from a low of $349 for the Hitachi to a high of $1,299 for the SawStop. The lowest price isn’t always the best in our opinion, we’re looking for the best value.  The Hitachi is an incredible deal at $349 and our top pick for price and value for a saw that has lots of power, a rack & pinion fence, and a solid stand.

If you’re not sure how to proceed, it’s important to take a breath and think about what you need out of a table saw. You could get a model with every possible bell and whistle, but there’s there no reason to do that if you’re not going to use it frequently. Likewise, you could just buy the cheapest model, but that doesn’t mean it’s going to be a fun machine to use.


In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.
The Shop Fox W1819 is our top table saw, due to its phenomenal power and great safety features. The DEWALT DWE7491RS was the best pick under $1000, due to its excellent power and portability. The Bosch 4100-09 was third on our list, featuring electronic speed control and easy blade changes. The DEWALT DW745 was the best for the money, as a smaller version of the DWE7491RS that packs the same amount of power. The Craftsman 21807 was last on our list since it has severe precision issues.
For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.
I really enjoyed your review and appreciate the significant time and effort put into it. How did you acquire the machines? Were they evaluation units provided by the manufacturers or did you buy them (randomly, like Consumer Reports)? If they were provided to you the cynic in me says you probably got cherry picked units. In looking at the various machines on line and checking out their comments, it’s quite clear pretty much all of them have a manufacturing distribution of performance and metrics e.g. for accuracy all the units you tested have comments ranging from great to truly awful. Same thing for build quality. I spent quite a while looking at the Dewalt but all the negative reviews on quality and accuracy turned me off it. I certainly do see many more positive reviews than negative reviews for the Dewalt, but it does leave you with the feeling that a dice roll is partly involved in buying a recommended table saw.
The safety features begin with the professional grade T-Glide Fence. Constructed from heavy gauge steel, this saw fence makes guiding material safe and secure anywhere on the work surface without needing to worry about rolling or slipping. Furthermore, the TGP252 also has an integrated overarm dust collection hood built into the saw guard which eliminates 99% of all sawdust generated by the woodcutting process. Sawdust is classified by the CDC as carcinogenic, so eliminating airborne sawdust from your workspace is essential to promoting your long term health.
The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25" ripping capacity, meaning tearing through thick sheets of plywood has never been easier.
When you need a full size cabinet saw that can handle just about any woodworking job you can throw at it, the Powermatic PM2000 is the one for you. As with all high end cabinet saws, the PM2000 features box-style cast iron trunnions for that refined, precise feel when adjusting the blade angle and height. Front control wheels are user-friendly cast iron hand wheels that feature precision-machined center locking pins for making every cut consistent and repeatable.
Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.
Contractor models also tend to be more powerful and more precise than portable saws, which gives them a definite upside if you’re going to be doing lots of work, or work that requires a fine degree of precision. This type can also be a good choice if you’re going to leave your table saw in one place for extended periods of time, while still being light enough that they can be moved if you need to do so.
You’ll be able to keep your space clear and work better with fewer distractions. The DEWALT DWE7490x 10 Inch Table Saw also comes with a push stick included in the kit so you’ll be able to take protective measures when you work. We’d recommend the DEWALT DWE749x to anyone as a good addition to their go to tools. It is an excellent tool and will help you do some of the best work of your life.

A magnetic switch is also good from a safety standpoint but may not be necessary on these smaller versions. A magnetic switch prevents the saw from starting back up if it loses power during a power outage. Basically, the power outage will turn off the saw. This is good because if for some reason the power were to come back on when you were not near the machine, the material could be shot out of it or damage the saw.
TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.

Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.
The continuous-read, tape measure–type scale is ingenious and easy to read, and Ridgid’s lifetime warranty covers it against breakage. The Ridgid saw has the most versatile miter gauge with holes and slots for mounting extensions and accessories. The designers have cleverly fashioned the stand to also serve as a left-side outfeed support for ripping plywood.
High RPM: Rotations per minute are an important consideration when you are looking to buy the ideal portable table saw. It ensures that you can cut the wood/material a lot more efficiently and accurately. It also means that the thickness can be adjusted easily, and you can get a plank to the thickness that you would like. The high RPM also makes sure that the cut is relatively smooth and the rips do not show up in the form of uneven edges. On an average, most table saws have a 15 amps motor. It is the RPM that makes a big difference in performance. Anything above 4500 is fantastic.

The Bosch 4100-09 10 Inch Table Saw is an expert tool that will be sure to impress its users with the reliable design and easy to use set up system. Our favorite feature was the gravity rise design that allows you to push the device around easily and focus more on getting the job done instead of wasting time trying to set up a complicated device. The tool is also coated in a powder coat that helps to improve the longevity of the device and features a collapsible design that is easy to fold up and down once you get to the job site.
However, thanks to the innovative safety technology incorporated into the design, you’ll never have to worry about incurring severe injury. The tool is capable of sensing human touch and will shut down within milliseconds of accidental contact. You’ll be able to work in a safe and clean space with no worries if you invest in the best quality tool like the SawStop table saw.
The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.
The final brand that’s definitely worth a mention when it comes to evaluating the brands we’ll be featuring in our table saw reviews is Ryobi. They’re largely known for manufacturing components for use in the automobile, electronics and telecommunications industry. However, they’ve more recently branched out into their own range of power tools and other hardware related tools, including table saws. With that taken into consideration, from our experience of Ryobi’s products, we’d definitely say that they’re a brand well worth keeping your eye on.
The advent of ever better motive power that came with 19th century developments led to ever more efficient and ever more compact power saws. The first recognizably modern table saws date to the latter decades of that century. With compact and powerful electric motors developed and refined throughout the 20th century, tables saws were widely available and were both compact enough for home use, yet powerful enough for nearly any lumber ripping task.
It's not really a great choice for professional woodworkers, but for home do-it-yourself users looking for a more than competent contractor saw for their workshop, the Ridgid R4512 is a terrific value. It lacks the SawStop's safety features, but comes in at less than a third of its price. Build quality is first rate, most users say, with a cast iron table that does good job of damping down vibration. Users add that it cuts smoothly and accurately.

A table saw has two main ways it can seriously hurt you. One is obvious and that is having any part of your body come into contact with the blade. Any table saw you are seriously considering should have a blade guard installed. The clearer the better. And make sure you leave it on. The blade guard can’t do its intended job from a workbench or shelf.

Great match-up and informative… however I too noticed that “No Load” RPMs varied quite a bit from chart to chart – for the same saw. We would expect some variation of 50 RPM as you had mentioned, but not 500 to 800. See that the Hitachi changed from 4400 down to 3700, Delta jumped from 3700 to 4400, Rigid from 3650 to 4350. Upon closer scrutiny… the order of “No Load” RPMs used in first chart may have been used in all subsequent charts. When the “Load” results were ordered by hi-to-low ranking, is it possible that the “No Load” data was not kept with its saw? If so, that changes the %drop results slightly for most RPM No-Load/Load,Speed charts. No too terrible. Lots of data… Good overall presentation though for use to make informed decisions. Thank you!

Table saws are pretty complicated pieces of kit and because of that, you can likely imagine that they’re also pretty dangerous at the same time. This is especially the case if you’re using a table saw for the first time. With that in mind, you’ll want to make sure that your table saw features appropriate safety features when buying. There’s nothing worse than falling victim to one of the many accidents that happen every single year as a result of using a table saw.

Our biggest surprise while running the best table saw review tests was in the cutting power and the quality of cut: There wasn’t much difference among them. All these saws ripped through 3-in.-thick oak without hesitating. We tried this test with the stock blades that came on the saws. Then we repeated the test using a top-quality blade in each saw.
×