In a direct drive, the blade is directly connected to the motor. So the motor can transfer all its power to the blade directly. There is practically no loss of power in this process. It produces much less vibration and noise in comparison to a belt drive. They are relatively small and lightweight. They are also safer! It also costs less so generally it is a winner. However, there are reasons to go for a belt drive for bigger jobs.
As you would expect, the most expensive saws made slightly smoother cuts. But the difference was negligible. The only saw that struggled to make smooth cuts in the super-thick oak was the Ryobi. In more common situations, like cutting 3/4-in.-thick material, Ryobi’s cut quality was fine. We found the blades included with all the saws to be adequate for most ripping tasks. But if you want cuts smooth enough for glue joints, you’ll have to invest in a better blade.

If you are interested in buying a new model, then do not hesitate to read the following lines. Before making a purchase, you need to consider several things. Rip, miter, bevel and cut are just some of the things you will be able to do with this tool. More than that, you can amplify its functionality by adding several accessories to it. As compared to traditional saws, the circular saw has the ability to move the material towards the blade, which means a much more precise cut. However, in order to help you find a unit that meets your requirements, here are some of the most important things to look for.
If you are making a cut that will require your hands to get close to the blade, (within 6 inches) use a push stick or two to eliminate the chances of your hand touching the blade. If this is a big concern for you, maybe consider a saw that uses flesh detection to stop the blade. The additional cost of the saw will be instantly appreciated the first time you need it.
More Power: Well, the mathematics of it is fairly simple. When you decide to look for the best table saws, it is always better to go for the one with the maximum horsepower. A saw that is underpowered won’t be of much help in any case. On an average, a motor with 1-2 hp can easily cut through 2-inch thick wood. For greater thickness, you need to opt for table saws with higher horsepower. For example, if you are focusing primarily on wood that is nearly 3 inches thicker, you need a 3-5 hp motor that would run on 240 Volts.

It has a brilliantly powerful 15 AMP motor, which can deliver 4,800 RPM of cutting power. Is is normally more than enough for most woodworkers and hobbyists. It has stowable anti-kickback pawls and and excellent riving knife and spreader for accurate cuts. This is a great entry level saw at a great price, definitely worth looking at for your next purchase or project.
In 1999, a Dewalt table saw came out that was considered one of the first hybrid saws. They are made with strong motor parts and the drive system is more advanced. The substantial trunnions in most hybrid saws are attached to the bottom of the saw to make the blade and the miter slit meet exactly and easier. These are much smaller than the cabinet saws.

The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.
From dust collection and onboard storage through to on/off switches and table extensions, most reputable table saws come equipped with everything you’ll need to rip up the wood of your choice. Whether it’s making your life easier with wheels enabling height and tilt adjustment or a safety feature like the magnetic switch, the functionality of table saws is impressive. You can upgrade the blades, get various jigs or dado blades and generally enhance the way your saw performs.

It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.

If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  
Changing a table saw blade may seem daunting, but it’s actually fairly simple and straightforward. You just need to keep a few safety precautions in mind and have the right tools You’ll need to start by making sure your table saw is off. Unplug the device and make sure that when you press the ‘on’ button the blade doesn’t spin. Now that you’re certain the area is safe, it’s time to start. You’ll want to find a screwdriver set and the spanners that came with your table saw before you get going.

DEWALT® table saws are available in both cordless and corded. Our portable table saws are compact for easy transportation between jobsites. They offer a rack and pinion fence system for fast, accurate fence adjustments. Our table saws are lightweight and feature a metal roll cage to ensure they can stand up to a rough jobsite. Tool-free guarding component adjustments make it faster and simpler to adjust as needed. Since the World’s First FLEXVOLT® cordless table saw was introduced, DEWALT has revolutionized the world of cordless construction tools. Every aspect of our table saws are designed to make your job easier.


The Bosch 4100-09 offers many advanced features, making it a very capable table saw for woodworking. The air-filled wheels and gravity rising stand makes this table saw functional and lightweight. Set up and tear down of the table saw is a breeze. This technology allows the table saw to be moved from place to place, even over the most rough and challenging areas of the work site. The 4100-09 weighs 39 pounds, making it the perfect portable table saw. Although it is lightweight, it is very durable and stable.
The bench top saws have a compact yet ergonomic design. Thanks to their lightweight feature, more and more people prefer to use them in their workshops. Despite the fact that they are not equipped with wheels, they can be considered portable, because they are very small. As such, they can easily be carried and transported from a place to another by almost anyone. Also, in comparison to the jobsite saws, the benchtop saws have a very limited rip capacity.

From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
Self-Aligning Accuracy – As well as power in your table saw, you’re also going to want it to be as accurate as possible. We can comfortably say that this table saw from Bosch achieves that formidably with its self-aligning accuracy. This basically means that the square lock rip fence aligns itself for accurate performance. If you’re going to be using your table saw regularly and know that you need to get the job done correctly, this will provide it.
Jet has a strong reputation for providing customers with durable power tools that operate just like professional models but cost less, and that is definitely true of this 10-inch table saw that comes with a riving knife. You’ll like the basic design of this model, which has an intuitive design that allows you to set it up and start cutting faster. It features both a solid cabinet as well as an extension table that stretches out from one end.
You should test the cutting depth of a saw when it is not cutting a bevel. This aspect helps in determining accurate and maximum cutting at 0 degrees. In considering bevel cutting, you should ensure the base plate is adjustable. Look out for adjustment allowance that your saw offers you such as 45, 50 or 90 degrees. The table saw should also be a feature with the flush housing so as to allow the table saw to cut very close to the edge of the wall. It is necessary to look out for this feature as will allow you to cut flooring to size at ease
The Bosch GTS1031 Portable Table Saw is an excellent tool for any craftsman - definitely one of the best tools you could add to your work arsenal. We love that it is easily transported from place to place thanks to its lightweight design and ergonomic carry handle. The design transfers all of the weight of the machine to a specified center of gravity and helps to make it easier to carry the 50 pound machine. The Bosch GTS1031 Portable Table Saw also comes with a smart guard system that helps the device perform at peak levels while keep you safe during your work.

More power is also associated with more control. More control also gives you the ability to cut tougher materials. Furthermore, more control allows you to use bigger blades with ease. For instance, a 1500W of the motor will result in swift movement of the blade as it spins. High RPM of the blade gives the user a greater chance of achieving accurate and precise cut. So, when shopping for a table saw, look out for a skill saw with the higher motor rating.

With a quick release riving knife, this Jet 708676PK XACTASAW Deluxe 5HP with 30 In. Rip Fence reduces the risk of binding and also cuts back on the kickbacks that you might otherwise feel. Its five-horsepower motor is one of the most powerful on the market and can make quick cuts in any type of wood. It also comes with a 30-inch rip fence making rip cuts, though you may find that this fence is a little too short your needs.


The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.
However, with proper use, table saws are generally safe tools, advanced blade stopping technology not needed. Therefore considering a saw without such safety features is fine for the cautious DIY user or for the professional carpenter and/or builder. Take into careful account the actual table size of the table saw you are considering. If you are going to be completing rip cuts in large sheets of plywood, then you need a saw with a table large enough to support these big pieces of lumber.

The SawStop SNS175-TGP36 HP Saw is one of the best stationary table saws on the market thanks to its incredible design and impressive build. The saw is able to fit larger dado blades and has an impressive maximum cut depth for you to work with. Additionally, thanks to the left blade tilt, you’ll be able to get work done faster thank you ever thought possible because the tilt helps to prevent boards from being stuck up against the fence. You’ll also be able to get work done quickly and efficiently thanks to the impressive safety system that was built into the saw.


It is equipped with plenty of important components and the motor is one of them. It differs from a model to another, but this depends on various circumstances. For example, the smaller models have direct-drive motors that run on 120V circuits. In comparison to all those powerful motors that produce up to 5 hp, the motors designed for smaller units can produce up to 2 hp. This power is enough for cutting thinner material sheets. Keep in mind that the 5hp motors operate on 240V.
There were really two major performance considerations we wanted to look at to help determine the best portable jobsite table saw: cutting power and dust collection. Power is an obvious choice. We want to make clean, straight cuts, but we don’t want to spend all day making them. Any saw can be calibrated to be straight and accurate, but some have to be babied more than others to get professional results.
The design is quite good. The SawStop safety system ensures smooth and flawless operation while protecting you from a variety of hazards. However, regardless of the safety aspects, you should always wear protective equipment, especially gloves and goggles. One of the most notable things about the design is the fact that it provides 99 percent dust collection both below and above the table. The riving knife maximizes kickback and also offers protection.
If you don't need a stand, a benchtop table saw can be an economical and practical choice. The DeWalt DW745 (Est. $300) isn't covered in any professional tests, but it gets excellent reviews from users. This saw is limited somewhat by its small size, as it has only a 20-inch rip capacity and can't make dado cuts. Nonetheless, it earns very high ratings at Amazon with an overall rating of 4.6 stars based on nearly 2,000 reviews. Meanwhile, the more than 600 that weigh in at Home Depot like it even a touch more, granting it a rating of 4.8 stars, with recommendations from 98 percent of users. Owners like its rack-and-pinion fence – the same design found on the larger DeWalt – which they say is accurate and very easy to adjust. Its light, portable size (just 45 pounds) is also a plus. However, like the DeWalt DWE7491RS, it gets a thumbs-down for its flimsy, awkward miter gauge and occasional quality-control problems.
The 15-amp motor is outstanding, developing up to 4HP and operating at a speed of 3650RPM. This is not quite as pacey as the DeWalt but still more than respectable. The other advantage to this motor is that – for a table saw, at least – it’s pretty quiet. Noise isn’t such an issue out on the job site but if you’re woodworking at home, the quiet motor is a real boon.
One of the most widely used power tools for carpenters is the table saw. For carpenters that don’t work exclusively in the shop a portable jobsite table saw is essential. For this Head-to-Head we’re focusing on corded portable 10″ jobsite table saws. We are not including cordless table saws in this test as we plan on doing another head-to-head exclusively for cordless table saws later this year as several are available now.

Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.


We put our hands on 10 of the most popular table saws and tested them for accuracy, power, and functionality. It took some time, but we have some fairly conclusive results. Table saws are undeniably the kings of rip cuts on the jobsite and in shops. The concept is simple: Place a motor below a solid table to turn a blade somewhere in the 4000-5000 RPM range through the surface and watch the sawdust fly. The idea may be simple, but the reality is much different. How big should the table be? What size blade should you use? How heavy can you get away with making it? For this shootout, we’re looking specifically to find the best portable jobsite table saw.
Finally, hybrid saws combine the lighter weight of the contractor saw with the more powerful motor and sturdier construction of the cabinet saw, at a price that’s easier for the occasional woodworker to stomach. They can run about $1,200 or so, and weigh in at under 300 pounds. Their motors are generally in the 1.5 to 1.75 HP range, and can be used with standard 110V outlets.

After reviewing several models we can truly say that metal components are more durable than plastic. Cast iron, for example, is a durable material that provides the most stable surface. It is capable of minimizing vibration and is much heavier than steel or aluminum. Every quality model has a smooth surface and sturdy legs that ensure stability. In what regards the motor and its components, you probably know that it’s quite difficult to check them by looking. However, any product should have a warranty and for a quality product, the manufacturer should offer at least a 3-year warranty.
You should test the cutting depth of a saw when it is not cutting a bevel. This aspect helps in determining accurate and maximum cutting at 0 degrees. In considering bevel cutting, you should ensure the base plate is adjustable. Look out for adjustment allowance that your saw offers you such as 45, 50 or 90 degrees. The table saw should also be a feature with the flush housing so as to allow the table saw to cut very close to the edge of the wall. It is necessary to look out for this feature as will allow you to cut flooring to size at ease

I really do like your site and being on Long Island there is a familiarity to the way y’all work. You are quick to respond to comments and put in a great effort but…. This review I feel you miss the mark. Out of box accuracy is important but. Ore important to a pro user is tool able to be adjusted to be near perfect and how does it hold this position. No comments on how solid the fences are, ie deflection movement, ease of micro adjust, etc. all the fancy self feed stuff etc, what saw feels the most powerful? Smoothest ? All theses kizmos are for the manufacturers to hype. Your strengths are that you actually use these machines, so your strengths are to BE MORE opinionated or biased not less because your opinion has meaning or weight. Let the know knowings use the kizmos and just give us your real opinions based on real use. Just my 2 cents.

Table saws can pose a serious risk of injury, since part of the spinning blade comes up above the surface of the table where it can come into contact with the user's hand as it guides the wood. Thanks to voluntary safety standards introduced by Underwriters Laboratories (UL) in 2007, pretty much all table saws now come with blade guards that minimize the risk. Modern guard systems are easier to remove and replace as needed – an important feature because inconvenient blade guards are apt to be left off the saw.
Smoothness & Accuracy: This is another important factor to be aware of. You need to make sure that you decide on a portable table saw with a blade that can cut any type of wood easily. The fence needs to be able to fix the wood securely, and a miter gauge adds to the overall accuracy element. It also significantly adds to the range of options you can use the table saw for.

A cabinet table saw is so named because it has an enclosed style base. This saw is the opposite of the contractor saw. Cabinet table saws are designed to be functional and lasting to meet the qualifications that are required by people who work with wood for a living. They are constructed to be more durable than contractor saws. Makita table saw offers many popular options at a very affordable price.
By the late 18th century, a new tool had been created that would eventually have the sawyers out of work: the circular saw. These early rotating saws were powered by a range of different forces, often including running water or wind, and sometimes driven by animal power. By the early 1800s, the sawmill was replacing the saw pit and its hardworking manual sawyers.
The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.

Other than getting a cutting tool that will lighten your work, investing in an item that will ensure you are satisfied by its construction, performance and longevity are the desire of every customer. DEWALT understands better the needs of various customers and has been in the business for a long time. The many year’s experiences have given the company trust in customers. Therefore, they manufacture strong tools with high performance and back them with a sustaining warranty. The table saw is designed with a portable style for use in any room comfortably.  15 amp, gives a powerful and consistent performance to ensure you don’t have pending jobs on various days. The large rip capacity makes it easy for you to cut even large materials comfortably. When using this saw, all you need is to keep your eyes open, it has a guide system that will provide accuracy and precision in your work automatically.

The stand strays from the idea that jobsite stands need to be wheeled. We can attribute this to its light weight. While it loses points for portability, Skilsaw’s design created the most stable stand of the entire group. Another benefit to going with this simple stand design is that it is certainly responsible for dropping the price point. Skilsaw is definitely the table saw you want to go with if you’re having to move your saw in and out of a truck bed rather than being able to wheel it up in a trailer.
If you’ve purchased a power tool in the past, Dewalt are a name that you’ve likely already heard of and that’s no surprise considering the standard of their products. They’ve been designing and manufacturing some of the world’s best power tools for well over 90 years, so you can likely imagine that you’re going to be in safe hands buying a table saw of any kind from Dewalt. It is worth mentioning though that Dewalt’s products are largely targeted at professional contractors and those within the building industry. However, that doesn’t mean that you can’t find a product in their range that’s suited to your needs.

We’ve approaching the end of the table saw reviews on this page and we’ve selected the GTS1031 10-Inch Portable Jobsite Table Saw from Bosch to conclude those reviews. Our reasoning behind choosing this particular saw is largely because it offers a good all round selection of functionality. As you’ll find over the course of this review, this is a table saw that provides portability, flexibility, power and more. It may not excel in all of those areas but if you’re stuck for choice when it comes to a table saw, this’ll get the job done.
Large Cutting Capacity – When you’re working as a professional, it goes without saying that you’re generally going to need to cut a number of different sizes of wood. From look at this product, it’s pretty clear that DEWALT definitely understand this. The table saw features a 32.5 rip capacity, which is designed to easily cut through a variety of different shelving and trim materials, whether they be large or small. It might not be the case that you instantly need the ability to cut larger materials, but it definitely couldn’t hurt to have the option.
Table saws are versatile enough to earn a spot in every home shop—even if that shop shares the garage with the family car. The market offers a range of saws, from $200 portable, less accurate saws to heavy and very accurate cabinet saws costing thousands. All the table saws shown here have 10-inch blades that can cut though stock up to 3 inches thick, and they meet the Underwriters Laboratories' safety standards to prevent kickback. Keep reading for extensive reviews of table saws, from portables to hybrid models.
×