Contractor models also tend to be more powerful and more precise than portable saws, which gives them a definite upside if you’re going to be doing lots of work, or work that requires a fine degree of precision. This type can also be a good choice if you’re going to leave your table saw in one place for extended periods of time, while still being light enough that they can be moved if you need to do so.

One of our favorite features of the device however, would have to be the load speed and maximum cutting depths. The DEWALT DWE7480 Compact Job-Site Table Saw can reach a load speed of 34,800 rpm and can reach a maximum cutting depth of 3 ⅛ inches when working at a 90 degree angle and 2 ¼ inches when working at a 45 degree angle. You’ll love the quick and accurate cuts you’ll be able to make while using this device - it will revolutionize the way you’re able to go about your job.

Another indication of how hard a table saw is working is monitoring the amperage (AMP) draw under loading conditions. We measured the amp draw for each saw using all three materials again at the same time we were recording RPMs. The first graph below shows the amp draw for each saw cutting plywood compared to the no-load amp draw. The white bar on the left indicates the no load amps and the colored bar on the right shows the maximum amp draw during the cut.
The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.
Patrick – Thanks for the feedback. Trust me, I wish we could spend more time on every aspect but we spent hundreds of hours as it was. I can tell you that the rack and pinion fences are much better than the standard fences of the past. Our entire group felt strongly that we’d prefer the rack and pinion on all the saws. We felt the Ridgid and Delta fences were the least impressive of the standard type.
One of my favorite features is the folding fence which essentially increases the surface area of the table to be able to handle larger projects. For instance, I ripped full size 4ft x 8ft sheets of plywood for a home remodel project and the Rockwell Table Saw performed flawlessly. I couldn’t have completed that particular project without the foldable fence extensions.
The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
If you want to finish your DIY project and you need to a circular saw mounted under a table, the DEWALT DWE7491RS is exactly what you are looking for. With so many models available on the market, more and more people think that buying a circular saw is a piece of cake. However, things are a bit different and choosing the right model for your needs can be an exhausting task. Nowadays, people who are interested in buying such a heavy-duty tool invest in the first one they stumble upon. This is a very big mistake. These tools are so different that you can easily end up with a device that doesn’t fulfill your needs. The DWE7491RS unit measures 24.5 x 31 x 31 in and weighs less than 100 pounds. It is a sturdy unit that features a rolling stand and provides maximum stability. Having a powerful 15-amp motor, this device is great for a plethora of reasons. It can make cuts ranging in depth from 2-1/4 inches at 45 degrees to 3-1/8 inches at 90 degrees. Moreover, it comes with a 1-1/2 inches dust port of the top of the blade and 2-1/2 inches dust port at the back end of the device. Its dual capability helps it capture dust both below and above the blade while leaving your work area clean at all times. After reviewing several models, we can truly say that the DEWALT DWE7491RS is among the highest ranked in the current market. It is a great unit that will surely meet all your requirements.
The stand is collapsible and wheeled like others, but it’s not the gravity-rise style. You’ll have to use a foot to stabilize it while you pivot it up or lower it down. The lower locks are released with your feet and there’s some question about the long term durability of the releases. An open housing design has two major results – motor cooling should be more efficient but it trades off storage for an extra blade. There’s really way too much to talk about here, so check out our full review of this model.
Another good table saw from Powermatic is its 1792006K Model PM2000 5 HP 3-Phase Table Saw with 50-Inch Accu-Fence System and Rout-R-Lift. The dust collection port moves much of the debris you produce away from your work area, but the cabinet itself has a sloped design that makes it easier to get under the cabinet cleaning. Its quick release riving knife not only reduces kickbacks but also reduces the risk of the knife binding.

Powerful cutting and portable convenience with the Delta Powerful cutting and portable convenience with the Delta 36-6022. The 1-step release stand and large wheels make it easy to move the saw to any jobsite. The 15 Amp commercial grade motor cuts through the toughest materials. UL approved 3-way guarding system with riving knife for safety and excellent dust ...  More + Product Details Close
IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:
Finally, hybrid saws combine the lighter weight of the contractor saw with the more powerful motor and sturdier construction of the cabinet saw, at a price that’s easier for the occasional woodworker to stomach. They can run about $1,200 or so, and weigh in at under 300 pounds. Their motors are generally in the 1.5 to 1.75 HP range, and can be used with standard 110V outlets.
"Ideal for both craftsmen and hobbyists, the SawStop 3.0 horsepower Professional Cabinet Saw (model PCS31230-TGP236) delivers the performance you need with the peace of mind only SawStop's patented safety system can provide. The safety system detects when someone accidentally contacts the spinning saw blade, and then stops the blade in milliseconds — resulting in just a nick on a SawStop saw instead of the devastating injury. Built to satisfy the toughest expert users, the Professional Cabinet Saw features superior dust collection and an exacting fit and finish. This model comes with a 36-inch T-Glide fence system for added strength and increased precision as well as rails and extension table." - Official Product Description
Our selection the top cabinet saw is the SawStop ICS51230-52 5 HP 230V 60 Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System. SawStop appears on our list a few times because the company makes saws that come with its own patented safety system that causes the blade to stop spinning as soon as it comes into contact with skin. We also like the extended fence system on this model, which accommodate more wood types and board lengths.
"Ideal for both craftsmen and hobbyists, the SawStop 3.0 horsepower Professional Cabinet Saw (model PCS31230-TGP236) delivers the performance you need with the peace of mind only SawStop's patented safety system can provide. The safety system detects when someone accidentally contacts the spinning saw blade, and then stops the blade in milliseconds — resulting in just a nick on a SawStop saw instead of the devastating injury. Built to satisfy the toughest expert users, the Professional Cabinet Saw features superior dust collection and an exacting fit and finish. This model comes with a 36-inch T-Glide fence system for added strength and increased precision as well as rails and extension table." - Official Product Description
In addition to its cutting versatility, the PM1000 also features a blade surround and collection hose for dust extraction. This method of collecting dust while the saw is in operation improves both blade visibility and air quality in the shop. Best of all, the 50-inch fence provides exceptional control when ripping lengthy sections of wood, and the extended geometry of the table allows for easier manipulation of longer workpieces.

As mentioned, the look is similar to a hybrid with a full enclosure. Looks can be deceptive, though… The core design purpose is for this saw to stand up to constant heavy use in a commercial setting. This is not a tool you buy for casual woodworking at home.These bulky, heavy units are built to last the distance. They can weigh up to 500 pounds. You’ll get an accuracy and rigidity not available in lesser types of table saw.Other table saws call for regular adjustments. With a cabinet saw, you won’t need to do this as often once it’s set up properly. 240V motors developing 3-5HP mean there’s very little the best cabinet table saw won’t rip through with ease. Large sheets of hardwood are no problem at all.
At a compact 45 pounds, the DEWALT DW745 Compact Jobsite Table Saw is the lightest table saw in our review. The saw's portability doesn't mean that ripping size is compromised, though. Thanks to extending fence guides, you've got 20 inches available. Depth of cut is on par with many bigger machines: at 90 degrees, it's 3 1/8 inches. At 45 degrees, it's 2 1/4 inches. Power comes from a 15-amp motor with a no-load speed of 3,850 RPM. This is ample enough for serious DIY projects and light-duty construction site work.
If you're currently looking for a cabinet table saw and it's the first time you actually need to buy one, then you should know that they come in a wide range of types, from the larger contractor saws to the portable table saws that most people seem to own. However, buying the right model for you depends on your needs and how you're going to use it.

DeWalt DWE7490X table saw is a pretty cool portable table saw. It’s a great blend of accuracy, portability, and power. Weighing only 58 lbs, this table saw might be pint-sized, but it’s not lacking power. It has an impressive 15 A motor, 28.5 in. rip capacity, 47-degree bevel capacity, and cut depth of 3-1/8 in (at 90 degrees). Not bad for a portable table saw. Other features we appreciate are its tool-free fence adjustments for convenience and its metal roll cage for extra durability. This package also includes a scissor style stand, which allows you to easily pack up this table saw and bring it with you anywhere the job takes you!


Smoothness & Accuracy: This is another important factor to be aware of. You need to make sure that you decide on a portable table saw with a blade that can cut any type of wood easily. The fence needs to be able to fix the wood securely, and a miter gauge adds to the overall accuracy element. It also significantly adds to the range of options you can use the table saw for.


Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.
Self-Aligning Accuracy – As well as power in your table saw, you’re also going to want it to be as accurate as possible. We can comfortably say that this table saw from Bosch achieves that formidably with its self-aligning accuracy. This basically means that the square lock rip fence aligns itself for accurate performance. If you’re going to be using your table saw regularly and know that you need to get the job done correctly, this will provide it.

It’s a challenge to identify the best portable table saws. They need to be the right mix of quality, performance, price, brand, and availability. In this article, we will attempt to cover all those points for our five tops picks in this burgeoning market sector. Our reviews are designed in a way that can help you concentrate on products that provide a pretty comprehensive package. While the market is full of options, it is always good to go for ones that highlight the unique versatility of this tool. We will also go over everything you need to know in our buying guide so that you can purchase a portable table saw with confidence.
June 7th! Leather couches (3), storage ottomans (2), queen & single beds, kitchen table & chairs, gliding chair, lamps, end table, washer & dryer, gas blower & weed whacker, 50 in Plasma TV, 19 & 12 in TVs, desk & shelves, metal fire pit, outdoor iron table & 2 chairs, outdoor porch swing & stand, circular saw, jig saw, sander, other assorted goodies! Cash & carry! 972-436-0328
A 50 rpm deviation at those speeds is approximately 1% variance which is well within the tolerance we should expect from taking the readings at a precise instant of time. The meters were in constant motion and we took the reading off of a single video frame that represented our determination of no-load speeds. We report them as our instruments showed them. 1% is acceptable.

I do not which is the best table saw, but I can tell you which is the worst. The rigid portable saw is a piece of garbage. I have purchased two in the last 4 years and the motor has failed in both, only to find that they do not sell a replacement motor. The Rigid customer service will not respond to any questions associated with the saw or replacement parts. I will not buy another Rigid tool and currently planning to try the Bosch table saw.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
The Bosch 4100-09 offers many advanced features, making it a very capable table saw for woodworking. The air-filled wheels and gravity rising stand makes this table saw functional and lightweight. Set up and tear down of the table saw is a breeze. This technology allows the table saw to be moved from place to place, even over the most rough and challenging areas of the work site. The 4100-09 weighs 39 pounds, making it the perfect portable table saw. Although it is lightweight, it is very durable and stable.

Scott – I’m assuming you’re talking about the “flatness” of the table and not leveling the saw correct? I will tell you that all jobsite table saws use light weight tables that are NOT machined cast iron like shop saws. Most of the jobsite saws are a light weight cast aluminum top, and NOT machined flat. So there are tolerances in the manufacturing that make it impossible to get a really flat surface. The thing is, in my opinion, for this type of saw it’s not really important. Job site saws are set up for ripping framing lumber, trim, and details that are not as precise as “woodworking” projects. If you need a cut that precise on a job then there are other better approaches including track saws and even pre-cutting materials in the shop. The DEWALT is very similar to the other saws with regard to the table.
I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!
You can’t talk about the best portable jobsite table saw without talking about portability. Portability boils down to a couple of important features. First and foremost, weight has a huge impact on how easily you can transport the saw, especially if it has to go into the bed of a truck rather than a trailer. If you’ve got a trailer, then a wheeled stand becomes your best friend. We looked at both.
The body of the blade is made from hardened steel, helping to extend the lifespan and keep up with the tooth quality. The kerf is a crazy-thin 0.098 inch—narrow to keep the cuts fast by reducing the amount of material that needs to be removed. Like most Diablo blades, you’ll pay a bit of a premium up front, but the blade lasts so much longer than others on the market that the cost per cut is much lower.
The biggest advantage of hybrid saws is the fact that they can be plugged in a regular 110V/220V outlet. Therefore, you don’t need any additional power sources in order to use these units. It quite a relief because you’ll avoid any further investments. These saws are quite easy to use if you know what you are doing. However, if you don’t, remember to read the manual before turning your saw on. It will save you a lot of hassle and also keep you safe.
Electric brakes in the saw is an important feature as helps the saw in reversing electricity in the motor, thus contributing to a precise cut. It is highly recommended that when you are buying a saw choose the one with on and off switch. The switch should be easily accessible to make work better and more efficient. In addition, the switch should have a cover. This will keep you from accidentally turning the saw on and damaging your work area or cutting yourself.
Both the riving knife and the blade itself has a quick release design that lets you remove each one in minutes after accessing the arbor lock and without using any special tools either. The blade guard has a similar design that allows you to remove and replace it without any tools. This guard does a good job of keeping your hands and any other body parts safe as you use the saw.
Designed to be Portable – In case you hadn’t already gathered from the above section, this is a table saw from Bosch that is clearly designed to be portable. If you’re going to need a table saw that can be moved on and off of a worksite with little effort, you’ll definitely find that to be the case with the Bosch 4100-09 and it’s included Gravity Rise Stand.

The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
More Power: Well, the mathematics of it is fairly simple. When you decide to look for the best table saws, it is always better to go for the one with the maximum horsepower. A saw that is underpowered won’t be of much help in any case. On an average, a motor with 1-2 hp can easily cut through 2-inch thick wood. For greater thickness, you need to opt for table saws with higher horsepower. For example, if you are focusing primarily on wood that is nearly 3 inches thicker, you need a 3-5 hp motor that would run on 240 Volts.

The simplest way to find out what size your table saw needs or indeed if you’re buying a special size is to consult the table saw user Manuel. I would make sure you do this as often there are many things in modern tables saws that could affect the blade size and type. This is because modern saws have many different amazing and varied features, things size blade guards, special safety mechanisms and arbor sizes etc. With the We recommend you spend some time reading your manual in detail to avoid possible issues
It’s not until you get a bunch of saws side by side in the shop that you start to see the difference between a $300 saw and a $500 saw. While the motors are all 15-amp, the more expensive saws have features like soft start to prolong motor and gear life, electronic feedback to maintain blade speed and gearing to maximize torque. If you look under the saws, you’ll see that the more expensive saws also have much beefier motor carriages and better-quality blade-adjusting mechanisms.
×