We took all of the data from the RPM and AMP measurements and added them to come up with the final performance rankings. For each saw we added up the total percentage decrease in RPM’s (for each material type) and added that to the total percentage increase in AMP’s (for each material type). This gives us a relative comparison of each saw over all 6 sets of data.
The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.
The Shop Fox W1819 is our top table saw, due to its phenomenal power and great safety features. The DEWALT DWE7491RS was the best pick under $1000, due to its excellent power and portability. The Bosch 4100-09 was third on our list, featuring electronic speed control and easy blade changes. The DEWALT DW745 was the best for the money, as a smaller version of the DWE7491RS that packs the same amount of power. The Craftsman 21807 was last on our list since it has severe precision issues.
What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.
If you don't need a stand, a benchtop table saw can be an economical and practical choice. The DeWalt DW745 (Est. $300) isn't covered in any professional tests, but it gets excellent reviews from users. This saw is limited somewhat by its small size, as it has only a 20-inch rip capacity and can't make dado cuts. Nonetheless, it earns very high ratings at Amazon with an overall rating of 4.6 stars based on nearly 2,000 reviews. Meanwhile, the more than 600 that weigh in at Home Depot like it even a touch more, granting it a rating of 4.8 stars, with recommendations from 98 percent of users. Owners like its rack-and-pinion fence – the same design found on the larger DeWalt – which they say is accurate and very easy to adjust. Its light, portable size (just 45 pounds) is also a plus. However, like the DeWalt DWE7491RS, it gets a thumbs-down for its flimsy, awkward miter gauge and occasional quality-control problems.
The Bosch 4100-09 offers many advanced features, making it a very capable table saw for woodworking. The air-filled wheels and gravity rising stand makes this table saw functional and lightweight. Set up and tear down of the table saw is a breeze. This technology allows the table saw to be moved from place to place, even over the most rough and challenging areas of the work site. The 4100-09 weighs 39 pounds, making it the perfect portable table saw. Although it is lightweight, it is very durable and stable.
The simplest way to find out what size your table saw needs or indeed if you’re buying a special size is to consult the table saw user Manuel. I would make sure you do this as often there are many things in modern tables saws that could affect the blade size and type. This is because modern saws have many different amazing and varied features, things size blade guards, special safety mechanisms and arbor sizes etc. With the We recommend you spend some time reading your manual in detail to avoid possible issues
If you are an avid hobbyist, this saw is made just for you. The company is known for its uncompromising quality and durability. This saw has a safety system where the blade stops and retracts automatically when it comes into contact with anything that is not wood. The microblade guards keep debris from flying all over your workshop. It is easy to change between blades. You will not require a riving knife to do this. Its award-winning dust collection system ensures that you have a clean and presentable workspace at the end of the day.
Jet also gives you different choices when it comes to the extension wings. Some customers prefer the cast iron wings because they add more weight and keep the table from shifting, but others prefer the stainless steel wings that are durable and easier to use. No matter which wings you choose, you’ll find that you can quickly and easily attach them to the table’s surface to extend the total amount of workspace you have.
Another saw that earns good marks from both professionals and users is the DeWalt DWE7491RS (Est. $500). Todd Fratzel of ToolBoxBuzz.com, who says he's normally a "huge fan" of Bosch table saws, nonetheless declares this DeWalt "the best overall job site + mobile stand option out there." He praises the power and accuracy of the table saw, adding that it had no trouble dealing with various materials he tested (3/4-inch plywood, 2x framing material, and 1x maple lumber). He also notes that its rip capacity of 32-1/2 inches is bigger than any other portable saw's – a full 7-1/2 inches bigger than the Bosch 4100-09's. Fratzel loves the wheeled mobile stand, which makes it easy for one person to move this fairly heavy saw (roughly 90 pounds). He says the stand is very easy to set up and allows for the saw to be stored on end, taking up less space.
In recent years, there has been a cloud of controversy surrounding the inherent safety issues surrounding the table saw. SawStop developed a flesh detection technology that pulls the blade below the table surface 3 milliseconds after coming into contact with skin. It really created a new class of table saw that, as of June 1st, finally has some competition in the form of Bosch’s REAXX.
I see the ovens next to 'fridge. Isn't that a no-no? The heat from the ovens make the 'fridge run to cool more when the ovens are used, upping the electric bill. They are also too far from the center of preparation. I would have put them against the long counter. It would also allow counter space by the fridge to place items when putting them in or taking them out of the 'fridge.
Ease Of Use: The convenience or ease of use is another key factor to take into account when deciding on the best portable table saw. You have to understand that this device should be something that can be carried easily, fixed simply and used efficiently as and when you need to. Maneuverability is a fundamental element in this matter as well. From setting it up to fixing the wood in place, you have to make sure that the table saw that you buy is convenient and simple to use in all situations and locations. The only caveat to this is if you have one fixed location in mind for 90% of your work or more.
We spent a lot of time setting up and taking down the saws to see how well the stands worked and how easy it was to install and remove the blade guard and anti-kickback pawls. Then we ran a torturous ripping test with 3-in.-thick slabs of oak to find the best table saw. And finally, we used the saws for more conventional tasks like cutting plywood and ripping framing lumber as another test to determine the best table saw.
For ideal usage, the on/off switch needs to be mounted on the front of the saw and should be easy to turn off with your knee or a swat without having to look at it to locate it. Most table saw models have a safety feature that is a plastic key that has to be inserted before the table saw can be turned on. Some may even have a way to padlock the switch.
Just in time!!! My Sears Craftsmen portable saw died on me last week. It was only 12 years old with minimal use. It was a nice saw with a nice sized table, not heavy, and a stand that separated and folded like an accordion. Unfortunately, as it turned out, the gear teeth on the worm drive had worn down to the point where the saw started slip and whine. Now that Sears is defunct (Canada), I have no other option than to replace it due to no parts being available.
An idea for next time you do a table saw review – what’s most important to me is REPEATABILITY of adjustments. Same for the fence – I want to know that, wherever I set it, it’s ALWAYS accurate and straight. I’m OK if the saw needs some tuning up out of the box – most saws do – but I really want to know that I can trust the saw to HOLD its adjustments, especially if I’m moving it around a lot. This I find is the weakness of jobsite saws in general – they just don’t STAY accurate for very long as vibration and just moving them around jar things out of position. Essentially, I want to know which of these saws is going to need constant fiddling, vs which ones ‘just work.’ with minimal fuss.
Table saws that can be found on the market are designed for different uses. There are four types that these table saws can be listed under. There are Portable saws, contractor saws, hybrid and cabinet saws. When exploring the possibility of a new saw you will need to understand what each of these mean and how each saw performs in their perspective class.
Methods for tilting the blade to cut bevels vary among the saws. The Porter-Cable saw is the only one with a conventional handwheel bevel control mounted on the side of the saw. The crank gives you great control for setting an exact angle. To set the bevel on the Bosch, DeWalt and Rockwell saws, you simply release the bevel-lock lever and tilt the saw to the preferred angle. It’s easy to go quickly from a 90-degree to a 45-degree bevel with this method. The Ridgid, Craftsman and Ryobi saws have a rack-and-pinion setup. These saws utilize the front crank for setting the bevel.
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
The fence on a table saw is one of its defining features and allows for precise, square, and repeatable cuts. Not all fences are equal though and a poorly built fence is a deal-breaker, in my opinion. Not only will a poorly built and implemented fence affect the quality of your cuts, but a fence that moves or is not square to the blade can cause your material to bind and kickback.
Cabinet table saws are not portable. They’re instead designed for use by professional woodworkers. That means that they’re designed to have a lot of power and to stand up to constant daily use. They have more steel and cast iron in their bodies to increase their durability, which also means that they tend to be lower-vibration than other units, which leads to cleaner cuts.
An excellent choice both for professional woodworkers and hobbyists with a more expansive tool budget, the Shop Fox W1819 is a 10 inch table saw ideal for making clean cuts along greater lengths of material without pinching or kickback. The blade itself is covered while in operation by a clear polycarbonate blade guard that moves back as the workpiece is passed along over the blade.
If you need a table saw that can travel, the Bosch 4100-09 consistently earns high marks. Reviewers praise its power, accuracy, easy setup, and easy blade changes. They also love the gravity-rise wheeled stand, which rolls smoothly and snaps open or folds flat in a single lever-activated motion. Finally, they appreciate the convenience of the blade guard system, complete with riving knife and anti-kickback pawls.
However, thanks to the innovative safety technology incorporated into the design, you’ll never have to worry about incurring severe injury. The tool is capable of sensing human touch and will shut down within milliseconds of accidental contact. You’ll be able to work in a safe and clean space with no worries if you invest in the best quality tool like the SawStop table saw.
It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.
The most critical safety feature on a table saw is the blade guard. It’s all that separates your fingers from the rapidly rotating blade. You need this to be transparent or it will make measuring awkward. The last thing you want is to be tempted to remove an unfit guard. Check closely for a clear, flexible blade guard. Safety is paramount when operating a table saw.
The final key factor that you’ll want to take into consideration when picking the right table saw is just how easy that table saw is to use. Obviously for experienced table saw users, ease of use might not be something that is so much of a big deal, but if this is going to be your first table saw, it’s definitely something that you’ll want to look out for. The last thing you want is to purchase a brand new table saw and find that you can’t use it.
Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
The Skilsaw SPT70WT-01 is a super high quality table saw with the power to match. The Diablo blade that comes with it will cut through 4×4 without any problems at all, like a knife through butter! One of the best features we noted was the fact that there is barely any vibration, this allows to you to cut as straight as an arrow, you can really feel the build quality with this saw.It has an extremely easy to use miter gauge, just a flick of the wrist to change the angle of cuts to exactly what you want.
Give yourself a reason to smile every time you enter in your workshop by investing in this powerful instrument. DEWALT as a company guarantee quality in all their products for the interests of customer satisfaction. This Jobsite table saw is not exceptional. Its designed to provide precision and last longer. The saw features pinion and rack system that makes adjusting the fence easy and convenient. In other words, you will not strain or shift your concentration while on work. The table saw is designed with a rolling stand that guarantees you professional performance in all your cuts. It also features telescoping fence rails that retract and extend for a small portable package of the saw. Additionally, the table saw is suitable for both wide and narrow rip cutting as the fence can adjust based on the type of material you are cutting. Using a 15amp motor, you are sure that the saw will get the job done within minutes and save you energy cost.
Almost all the features you like about the more expensive SawStop cabinet saws are available in this PCS31230-TGP236 3-HP Professional Cabinet Saw Assembly with 36-Inch Professional T-Glide Fence System, Rails and Extension Table, which costs much less. This model comes in a black finish with accents and features like its emergency stop button in a brighter red color that make those features easy to see. It also features a taller height designed to reduce strain on your back as you saw.
This portable jobsite table saw head-to-head includes 8 saws from; Bosch, Delta, DEWALT, Hitachi, Makita, Ridgid, SawStop and Skilsaw. Originally, we had also to include Ryobi as a budget friendly option for DIY’ers or guys just starting in the trades. However, we were not able to adapt that saw to our testing rigs so we pulled it from the testing (you may see some photos with the saw but again we’re not including it in the results).
Innovative Gravity Rise Sand – When it comes to the features of Bosch’s 4100-09 table saw, there’s clearly only one place to start and that’s with the Gravity Rise Stand that comes as part of the package here. This is basically a stand that can be intelligently adjusted to your liking and then wheeled away when you’re finished using the table saw. It’s a pretty innovative idea from Bosch and definitely one of the best stands that we’ve seen included with any table saw that we’ve reviewed or on the market.
If you’re looking for one of the most powerful products on the market, you’ll find those such options within the 3-5 horsepower range. As you can likely imagine, these are products largely targeted at professionals looking to use their table saw on a day to day basis. If you’re a hobbyist or occasional contractor who doesn’t necessarily want to shell out a fortune on a table saw, you should find that between 1-2 horsepower does the job.
At first glance, the Bosch 10-Inch Worksite Table Saw may seem to be nothing exceptional. However, it's powered by the best motor in its class, and it does everything well. True, the motor is a 15 amp unit like the others on our list, but it produces 4 HP where the others produce only 1.5 to 2 HP. This is a noticeable step up in a vital area! The wheeled frame is extremely helpful for moving around your shop or garage, but keep in mind that those tires aren’t heavy-duty; you have to be careful with them on a worksite littered with nails and screws.
The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25" ripping capacity, meaning tearing through thick sheets of plywood has never been easier.
The cabinet saws are the most powerful woodworking machines. They are durable and strong enough to resist for a long period of time. Most people prefer them because of their impressive features which make them precise and extremely accurate. The motors of these units usually run on 240V and produce from 3 to 5 hp. As mentioned before they are very heavy. Most models weight more than 500 pounds, however, this makes them very stable.
We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.
Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.
Scott – I’m assuming you’re talking about the “flatness” of the table and not leveling the saw correct? I will tell you that all jobsite table saws use light weight tables that are NOT machined cast iron like shop saws. Most of the jobsite saws are a light weight cast aluminum top, and NOT machined flat. So there are tolerances in the manufacturing that make it impossible to get a really flat surface. The thing is, in my opinion, for this type of saw it’s not really important. Job site saws are set up for ripping framing lumber, trim, and details that are not as precise as “woodworking” projects. If you need a cut that precise on a job then there are other better approaches including track saws and even pre-cutting materials in the shop. The DEWALT is very similar to the other saws with regard to the table.
Table saws in this best table saw review run the gamut in price and quality. You can buy a table saw for as little as $150, and if you use it just to occasionally rip a board, that may be all the saw you need. If you want a saw that’s easy to carry and you don’t need to rip sheets of plywood in half, look for a “compact” saw like the DeWalt DW745 (shown) or the Bosch GTS1031. If you have room for a little larger saw that’s slightly less portable but capable of wide rips, consider one of the best table saws we review here. And finally, if you want to build cabinets or furniture and have a big enough work area, you can step up to a stationary contractor’s saw like the Ridgid R4512 (shown), for about $650.