Contractor models also tend to be more powerful and more precise than portable saws, which gives them a definite upside if you’re going to be doing lots of work, or work that requires a fine degree of precision. This type can also be a good choice if you’re going to leave your table saw in one place for extended periods of time, while still being light enough that they can be moved if you need to do so.
Now you’re ready to advance on to the next step. Take the spanners out and get ready to put them on the nut. You’ll want to make sure that they are the spanners that originally came with your table saw because they have been tested especially for your machine to make sure they won’t over tighten the nut or screws. Once you’ve made sure that you have the correct spanners, place them on the nut. Use the first spanner with your right hand and use it to stabilize your grip.
Inspect your wood carefully to make sure that you are able to maintain a safe working environment and are able to complete high quality work. Now that you’ve got these things in mind there are only a few more things you’ll need to remember before you’re ready to get to work! First, remember that the blade spins towards you, the operator. This means that you’ll always want to feed the wood to the machine by pushing it towards the blade and away from you.
If you are interested in buying a new model, then do not hesitate to read the following lines. Before making a purchase, you need to consider several things. Rip, miter, bevel and cut are just some of the things you will be able to do with this tool. More than that, you can amplify its functionality by adding several accessories to it. As compared to traditional saws, the circular saw has the ability to move the material towards the blade, which means a much more precise cut. However, in order to help you find a unit that meets your requirements, here are some of the most important things to look for.
By the late 18th century, a new tool had been created that would eventually have the sawyers out of work: the circular saw. These early rotating saws were powered by a range of different forces, often including running water or wind, and sometimes driven by animal power. By the early 1800s, the sawmill was replacing the saw pit and its hardworking manual sawyers.
We love the Makita Contractor Table Saw for its convenient design and sheer power. The device is powered by a powerful 15 amp motor that enables it to work incredibly well and efficiently. The whole ensemble comes with a superior safety system, a miter gauge, a rip fence, and a 32 inch blade to ensure that you’re prepared to get going and get the job done as soon as you receive the package. We also appreciate the measures taken to protect the blade and machine during transportation like the case that encloses it underneath the table.

Just used this saw for the first time today and I love it. Instructions for putting the stand together were not very clear. There's a lot of very detailed reviews here, so there isn't much I can add that hasn't already been said; but one thing I didn't know until using it is that the rear legs are angled further back than the front ones to provide more stability when pushing stock through the saw. Only used it a few times today, but it was a pleasure to use.
First, this is not a precise table saw.  This is due to a mix of design flaws and poor manufacturing choices. The placement of the blade guard makes it impossible to see the blade during the cut, which is going to make you less precise and frustrated to boot. The fence is cheap, and may or may not be straight, but even if it is, you have to deal with the fact that flaws in the table itself may result in it not clamping down straight.
Love the video. It was very helpful, answered some of the questions I've had and wondered if you can expand this a bit further. I have a Thomasville bedroom set that I bought in 1981. After all of the years of my wife using hairspray, there's a layer of it on the bed's foot board and the top and leading edge of the dresser. Will this technique remove the hair spray and restore the finish? I tried using denatured alcohol to clean it in the past but stopped short of using a sanding pad or working it to the point that nit was anything but tacky. Sounds like I didn't work it long enough. Am I right or do I need to do something else? These areas are the only bad spots on any of the 5 pieces of the set. Thanks!

When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.
"Ideal for both craftsmen and hobbyists, the SawStop 3.0 horsepower Professional Cabinet Saw (model PCS31230-TGP236) delivers the performance you need with the peace of mind only SawStop's patented safety system can provide. The safety system detects when someone accidentally contacts the spinning saw blade, and then stops the blade in milliseconds — resulting in just a nick on a SawStop saw instead of the devastating injury. Built to satisfy the toughest expert users, the Professional Cabinet Saw features superior dust collection and an exacting fit and finish. This model comes with a 36-inch T-Glide fence system for added strength and increased precision as well as rails and extension table." - Official Product Description

All the articles on this website are short and punchy without much filler, but because there is so much to learn about table saws it will still take you the better part of an afternoon to read through them all. For those who don’t have that kind of time, or those who already know a great deal about table saws, this is the section that will take you to the best table saw for your needs.
×