The biggest thing that is making me watch less and less is the fact that most people will never use half the products you do. Like the Lattice. 99.9% of your viewers will have to use store Lattice as cost is to be considered. I estimate that each piece of Lattice you put on this house costs about $50 finished. Multiply that by 20 sheets and your at a cool $1000 for your Lattice. Most of us would go to the store and purchase 10 Lattice sheets for about $300. 10 sheets as each make up two panels. It would be really nice, for a change, that you would fix up a house the same way most of us would. Probably the reason Ask This Old House has out classed This Old House.

There’s a lot to like about this saw. The stand is easy to set up and very sturdy. We like the smooth-operating table extension and the blade guard’s hold-up feature and ease of installation. The only downside we found is that the motor mount is less rigid than those on the other saws we tested. We suspect that’s why the cut quality on our torture test was not as good with this saw.


The DeWalt DWE7499GD table saw earns a third place finish in the safety category thanks to their GuardDetect technology. This doesn’t prevent you from using the saw without the pawls and blade guard in place, but it does require you to physically indicate you are aware they’re not in place. Ideally, this gives your mind one last opportunity to consciously note the additional care that needs to take place before cutting.
From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.

When you purchase your table saw, more than likely it will have standard 10” carbide tipped blade that is good for general purpose use. This blade is capable of cross cutting a 4 x 4. If you replace it with a 40 tooth combination blade you will improve the quality of your cuts significantly and more than likely be much happier with the blade overall. You can get specialty blades also if you are going to be cutting other materials as well.


These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.
Deciding on what portable saw to get is not an easy task. There is so much out there on the market and such a wide combination of options. You can use our top 5 picks to get a taste of what’s out there and maybe find your perfect portable power saw right off the bat. However, we feel that you should also be equipped with the knowledge to go out and make your own decisions on portable table saws. We are going to run through the most important factors and features to consider before you make your purchase. These are factors that have a direct impact on performance.
If you’re a professional looking for a great table saw for the worksite, you’ll love the features and performance of the DEWALT DWE7480. Equipped with the Site-Pro Modular Guarding System has a rack and pinion telescoping fence rail that will allow you to make fast, smooth and accurate adjustments. This is the perfect table saw for cutting larger shelving and trim easily. With a 15 AMP 4800 rpm motor, you will go through all types of wood, even hardwood, with ease.
If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.
For any kind of professional woodworking and large scale construction work, the cabinet table saw is the one for the job. These types of table saws are often called stationary saws. The motor is protected in a cast iron and steel cabinet that reduces noise and vibration as well. With reduced vibration comes better accuracy which is always the desired effect, especially for professionals. The motor us a powerful 3-5 hp and requires a 220-volt outlet. If you are using it in a home workshop, a special outlet may need to be installed if 220s are not already installed in your garage or shop. Measuring about 28” x 43” and weighing in at over 400 pounds, these table saws were not designed to be portable. The large work surface is ideal for cutting large pieces with ease. Cabinet saws can use a 12” blade with no problem, although a 10” blade is the most commonly used. It is the most expensive of all of the styles of table saws.

Reviewers recommend these models for easy transport to jobsites and for easy storage in a small workshop. Portable table saws come in two types. Benchtop saws sit on top of a workbench and are light enough to pick up and carry; jobsite saws are mounted on folding stands, usually with wheels for easier transport. The main drawbacks of a portable saw are its lower power and smaller table, which makes it tricky to cut larger lumber and sheet material such as plywood. Prices for portable saws start at less than $200, but the best-rated models typically cost $300 or more.

Ridgid’s fence is outstanding for its design. Its large front plate helps stabilize it and the whole thing just feels solid. There’s very little play compared to some of the others and we were consistently able to lock it down perfectly square. We like the pinion style bevel adjustment. It’s not quite a good as a separate adjustment wheel, but a great improvement over simple sliding. We also like the independent locks for both height and bevel. It’s not often that a height lock would be required, but there’s an element of confidence that comes from knowing it won’t be going anywhere.
The Steel City 35955 also comes with a new table insert system, a seamless table top that offers users a flat surface on which they can work on, but also the Push Stick safety system which prevents injuries to the fingers while using the table saw. Warranty wise, you get 2 years limited warranty, which is enough to give users peace of mind that they’re covered for a long time.

"Ideal for both craftsmen and hobbyists, the SawStop 3.0 horsepower Professional Cabinet Saw (model PCS31230-TGP236) delivers the performance you need with the peace of mind only SawStop's patented safety system can provide. The safety system detects when someone accidentally contacts the spinning saw blade, and then stops the blade in milliseconds — resulting in just a nick on a SawStop saw instead of the devastating injury. Built to satisfy the toughest expert users, the Professional Cabinet Saw features superior dust collection and an exacting fit and finish. This model comes with a 36-inch T-Glide fence system for added strength and increased precision as well as rails and extension table." - Official Product Description


It runs off of a powerful 15 amp motor that enables it to attain speeds of up to 3,850 rpm and has a 20 inch rip capacity. It also has a handy dust storage port to help it stay more productive and efficient by keeping the space clean. You’ll enjoy working with this remarkable tool if you’re constantly on the move and will be able to use it for many years to come thanks to its sturdy design.
Bosch 10” table saw has it all in terms of precision and accuracy. It has a riving knife system for high material controls and visibility in cutting. The blade is designed with anti-kickback pawls to ensure once you start cutting, you will get accurate results to the end. The entire unit is designed with heavy-duty material for durability. The square lock rip fence has adjustable style to guarantee continued accuracy and precision in all your work. Additionally, the table saw has an easy to transport design with additional tabletops handles for portability. You can also regulate the cutting speed of the table saw to the place you are comfortable.
Often called benchtop, jobsite, or worksite saws, portable table saws are typically made of lightweight materials, such as an aluminum table top, so that they’re easy to move from place to place. Sometimes they’ll have wheels attached to make shifting them around even easier. The motors on portable saws are also much smaller than on other types of table saws, and are typically less powerful.

In a video review at Tools of the Trade, finish carpenter Jesse Wright finds few negatives and a lot of positives for the DWE7491RS. Wright says this table saw is larger than he normally likes for a portable saw, but its size allows it to tackle tasks that would otherwise be out of reach of a jobsite saw and also makes it very solid and stable. The DWE7491RS also earns a perfect five-star rating from Popular Mechanics, which says it cuts well, is very stable, and has plenty of handy features. The reviewer's only complaint is that the saw is very loud.
One of my favorite features is the folding fence which essentially increases the surface area of the table to be able to handle larger projects. For instance, I ripped full size 4ft x 8ft sheets of plywood for a home remodel project and the Rockwell Table Saw performed flawlessly. I couldn’t have completed that particular project without the foldable fence extensions.
The only flaw might be the occasional false detection by the safety system. This will usually only happen if the lumber is wet or it is used primarily in the outdoors. You have to weigh the safety features against the type of work you do. If you are constantly working in wet or damp environments, it might not be worth the headache. If not, it’s 100% worth the benefits!
Though this Jet 708674PK XACTASAW Deluxe 3HP Cabinet Saw comes with the same three-horsepower motor found on the last cabinet saw, it comes with a shorter 30-inch rip fence that may be a little too short some of your projects. It features all the same great features that made Jet so popular with contractors, including a cast-iron enclosed cabinet that stops dust from entering the motor and a poly-v drive belt system that runs more quietly than other belt systems.
It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.
In a video review at Tools of the Trade, finish carpenter Jesse Wright finds few negatives and a lot of positives for the DWE7491RS. Wright says this table saw is larger than he normally likes for a portable saw, but its size allows it to tackle tasks that would otherwise be out of reach of a jobsite saw and also makes it very solid and stable. The DWE7491RS also earns a perfect five-star rating from Popular Mechanics, which says it cuts well, is very stable, and has plenty of handy features. The reviewer's only complaint is that the saw is very loud.
For ideal usage, the on/off switch needs to be mounted on the front of the saw and should be easy to turn off with your knee or a swat without having to look at it to locate it. Most table saw models have a safety feature that is a plastic key that has to be inserted before the table saw can be turned on. Some may even have a way to padlock the switch.
Ryobi’s RTS21G comes in as the only table saw in the group under $200. It’s lightweight, reasonably compact, and we got acceptable jobsite cuts with the upgraded Diablo blade. The throat plate uses magnets to hold it in place while leaving it easy to remove for blade access. Using a threaded rod to push the height adjustment up, you’ll notice it’s easier and smoother on the way down. The stand folds up and can be Velcro-strapped to the back, though it’s a bit wobbly compared to the others when ready for action.
Perfect for both hobbyists and craftsmen, the PCS31230-TGP252 from SawStop is a 3 HP cabinet saw that delivers excellent performance while featuring the company’s patented safety system to ensure maximum safety during use. The safety system is similar to that of the G0690 from Grizzly where the blade stops in milliseconds after it comes in contact with flesh. Designed and built in order to satisfy the needs of the most demanding users, the PCS31230-TGP252 features an exacting finish and feet and a superior dust collection system. For increased precision and added strength, the PCS31230-TGP252 features a fifty two inch T-Glide fence system, but also an extension table and rails.
When it comes to both appliances and power tools, Bosch is one of the most recognized brands out there. It is equipped with a 15-amp electric motor which has 3650 rpm. Moreover, the diameter of its blade is 10 inches, while the rip capacity is about 25 inches. As compared to other similar units, the Bosch 4100-09 comes with a plethora of safety features, including an arbor lock mechanism which helps you change the blade with ease. In what regards the design of this unit, it’s important to know that it is pretty compact. It measures 39.13 x 30 x 20.9 inches and weighs no more than 60 pounds. Also, keep in mind that the distance between the work surface and the floor is only 37.5 inches. Thanks to the unique properties of the carbide material, the unit is considered to be one of the most durable tools on the market. It is able to cut through pine and plywood which are the softer types of wood out there. Considering its impressive features and powerful motor, the Bosch 4100-09 will certainly be a welcome addition to any workshop.
Another saw that earns good marks from both professionals and users is the DeWalt DWE7491RS (Est. $500). Todd Fratzel of ToolBoxBuzz.com, who says he's normally a "huge fan" of Bosch table saws, nonetheless declares this DeWalt "the best overall job site + mobile stand option out there." He praises the power and accuracy of the table saw, adding that it had no trouble dealing with various materials he tested (3/4-inch plywood, 2x framing material, and 1x maple lumber). He also notes that its rip capacity of 32-1/2 inches is bigger than any other portable saw's – a full 7-1/2 inches bigger than the Bosch 4100-09's. Fratzel loves the wheeled mobile stand, which makes it easy for one person to move this fairly heavy saw (roughly 90 pounds). He says the stand is very easy to set up and allows for the saw to be stored on end, taking up less space.
Regarding reliability, Dewalt is a fairly dependable brand in the world of portable table saws. This latest offering from Dewalt comes with a big rolling stand that adds to the convenience element. It quickly cuts through over 3 inches depth at 90 degrees and nearly 2.25 inches at 45 degrees. This power is being driven by the powerful 15 amp motor. It cuts small and narrow strips of wood as well as large chunks.
The marketplace today is filled with a variety of options at every price range. Once, you have figured out your price range and needs; you should be able to find a choice among our top 5 picks. You can also use our buying guide to inform that choice or to inform your search for a suitable portable table saw in the wider market. There is so much out there, and the quality is getting better every year!
You often find that many contractors have a love hate relationship with blade guards. Many contractors and woodworkers simply find they often get in the way and can often get wood stuck in them. But many manufacturers are improving these guard’s year on year and now many of them are very advanced and will help keep your fingers from getting hurt, we always advise you to consider the table saw blade feature on any table saw in detail as it could one day help saw you.

If you spend a lot of time working with wood in your garage or workshop, you know the importance of having the best table saw on the market. Many craftsmen find that they feel connected to their work, and because of this they need tools that will work efficiently and reliably. If you’re invested in the art of carpentry, woodcarving, or any other wood related trade, you know that you need a machine that can work efficiently without overwhelming your budget.


If the aforementioned portable table saw is largely targeted at homeowners and those simply looking to complete the odd job, we’d definitely argue that a contractor table saw is aimed at well, contractors who need to transport their saw. You’ll find that a contractor table saw does offer some degree of portability, whilst still managing to maintain some of a complete table saw. With that in mind, some users describe this as the perfect sweet spot when it comes to table saws, offering a nice combination between power and portability.

Due to the position of the motor, dust collection is often an issue with these units, especially in comparison to the cabinet type. However, an industrial vacuum is usually a small and worthy investment which should solve the issue effectively. The main advantage of this type is the fact that it’s much cheaper than its nearest equivalent – the cabinet type.
The differentiating factor is workshop realestate: it takes up nearly 2 square feet less space than its larger, more powerful counterpart, making it ideal for craftsmen with less workspace who don’t need the extra horsepower for cutting heavier hardwood materials. Best of all, it includes SawStops 5 millisecond safety system to protect craftsmen from accidents that can lead to serious and permanent traumatic injuries.
All these saws have attached, collapsible stands with wheels that allow you to roll them around when they’re folded up. A few, like the DeWalt, Rockwell and Ryobi, can’t be wheeled around after they’re set up. But the biggest difference between stands is in how easy it is to set them up. The Ridgid and Bosch have nearly identical stands that work great and require you to only flip or depress one lever to unlock the stand. These are our favorites. The DeWalt stand is the sturdiest of the bunch and very intuitive. It sets up like a card table with legs that fold out and snap into place. The remaining candidates for best table saw have several different stand systems that aren’t quite as easy to set up but that work fine once you get the hang of them.
×