If you want a table saw that helps you deliver products faster, the Bosch 4100-09 could be what you’ve been waiting for. It has a Gravity-Rise stand that is built for efficient and accurate setup and takes down.The portable construction makes it easy to bring to any worksite with minimal trouble. Only weighing 39 pounds, you will have no problem transporting this table saw wherever you need to go. The Bosch 4100-09 is a powerful saw that is made for the kind of high precision cutting that professionals and DIYers are looking for. It has a 15 AMP, 4 HP motor that generates 3,650 RPMs for clean cuts every time.
This next factor to take into consideration when it comes to buying a table saw is more of a safety feature but one that you’ll want to look for in every table saw. It’s basically an automatic switch that turns of the table saw when you walk away. It’s often the case with some cheaper table saws that when you’ve finished using the table saw and forget to flick the power switch, the unit will remain on. This leaves anyone who goes near the table saw open to a considerable amount of danger.
It has a brilliantly powerful 15 AMP motor, which can deliver 4,800 RPM of cutting power. Is is normally more than enough for most woodworkers and hobbyists. It has stowable anti-kickback pawls and and excellent riving knife and spreader for accurate cuts. This is a great entry level saw at a great price, definitely worth looking at for your next purchase or project.
Outfeed capacity is almost always the depth of the table. Pros using a jobsite table saw can opt to put a sawhorse or other support to hold the material after it passes the blade. There are a few models running around that give you some extra outfeed support, though. Most of the time, you’ll just have a buddy help guide the cut through from a safe stance on the behind the saw.
Even though the trunnion mechanism from Powermatic has been known to be the best there is, further refinements have been made to it in order to make it even better. The conically shaped worm gear drive with better surface area, the high end bearings, but also the cast iron, box style construction combine with the solid and smooth feel of the height and tilt adjustments. Thanks to the adjustable backlash, it’s very easy for users to adjust the mechanism back to the factory fresh feel and clearances.

We don’t always post the point totals when we do a shootout like this because it gets complicated – you have to decide what the important features and performance categories are, determine how much weight each one should hold, and then actually hash out the scores with the team. That said, some of these table saws scored so close to each other that I didn’t feel it was fair to just leave it up to the rankings.
Table saws in this best table saw review run the gamut in price and quality. You can buy a table saw for as little as $150, and if you use it just to occasionally rip a board, that may be all the saw you need. If you want a saw that’s easy to carry and you don’t need to rip sheets of plywood in half, look for a “compact” saw like the DeWalt DW745 (shown) or the Bosch GTS1031. If you have room for a little larger saw that’s slightly less portable but capable of wide rips, consider one of the best table saws we review here. And finally, if you want to build cabinets or furniture and have a big enough work area, you can step up to a stationary contractor’s saw like the Ridgid R4512 (shown), for about $650.
Still featuring the T-Glide Fence System for smooth, safe operation without compromising on precision measurements and secure locking for repeatable cutting, the TGP236 is still an exceptional cabinet saw in its own right Furthermore, the blade height and angle are still fully adjustable via the comfortably large hand wheels on the front and side of the cabinet itself.
When you purchase your table saw, more than likely it will have standard 10” carbide tipped blade that is good for general purpose use. This blade is capable of cross cutting a 4 x 4. If you replace it with a 40 tooth combination blade you will improve the quality of your cuts significantly and more than likely be much happier with the blade overall. You can get specialty blades also if you are going to be cutting other materials as well.
Before you decide to invest in a unit, you must first know what to look for in order to find the best table saw. Many people think buying a table saw is a piece of cake, but the reality is completely different. There are a few things you should think about before buying one, especially if you don’t have any previous experience. Take a moment and read this article, it will help you a lot.
To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.
Hybrid saws will often match in terms of power but very rarely have the stability and durability of a cabinet saw, so often they work well in a home work shop where you can add extra stands etc to help. One thing to think about though is that because they won’t be as stable this can often compromise on the quality of the cuts, this is something you must think about when deciding. Read More
It’s often overwhelming when looking for new power tools and products online. So many features, specs and brands etc to research and review. So, what should you look for when buying a new table saw? One thing we always mention is to make sure you read as many table saw reviews as you can before purchasing one, this will insure you have the best table saw for your requirements.

It’s often overwhelming when looking for new power tools and products online. So many features, specs and brands etc to research and review. So, what should you look for when buying a new table saw? One thing we always mention is to make sure you read as many table saw reviews as you can before purchasing one, this will insure you have the best table saw for your requirements.

Using improper technique with this can lead to unsatisfactory results. Next, remember to always keep the resistance and kickback the machine will give off under control by using the fence. Make sure that the fence is adjusted in such a way that will keep the wood tightly wedged between the fence and the blade and that you are able to secure the fence down properly before you begin work.
Affordable Price Point – The price of the product is something that you’ll want to carefully consider when it comes to buying a table saw. This is largely because different people have different budgets to work with. Coming in at well under $100, you can likely imagine that this table saw from Ryobi comes in at the lower end of the market and for that low price point, you are going to have to make some compromises in terms of power and speed. However, occasional hobbyists should find that this table saw still gets the job done well.
Great job with this testing. As far as the Hitachi. Many sources online point to minimal startups of the Hitachi c10rj before becoming unusable (not starting). The soft start module apparently doesn’t hold up. If it happens in 30 days it can go back to the store but after 30 days you call Hitachi (most described as unpleasant) drive to your closet Hitachi Service center and wait (up to months). I really like the Hitachi myself but am afraid of the soft start module error. THANKS FOR ALL THE GREAT WORK AND CONTENT. Please forgive any punctuation etc. This is tough on phone.
Another important element of every model is the fence. Without the fence, you cannot make a precise cut. The most common type of fence that you can find on these units is the T-square fence. However, before getting into that let’s go over the most important characteristics a quality fence must have. First of all, it is important to know the role of the fence. It allows for hassle-free adjustment both vertically and horizontally. Also, it must be placed on the rails firmly, so you don’t encounter resistance while moving it. However, if this happens you can apply wax. Now, let’s have a look at the T-square fence. It is so popular because it is easy to adjust and maneuver. More than that, it is extremely accurate.

To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.
In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.
The Powermatic 1792001K PM2000 is an award winning cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. The 1792001K PM2000 is the result of years of work and research and hundreds of interviews with woodworkers that offered input which was eventually implemented in the saw. The performance, reliably and safety of this saw are so great, that they actually set a new standard by which all other cabinet saws are judged.
The Skilsaw SPT70WT-01 is a super high quality table saw with the power to match. The Diablo blade that comes with it will cut through 4×4 without any problems at all, like a knife through butter! One of the best features we noted was the fact that there is barely any vibration, this allows to you to cut as straight as an arrow, you can really feel the build quality with this saw.It has an extremely easy to use miter gauge, just a flick of the wrist to change the angle of cuts to exactly what you want.
The bench table saw is the least expensive of the four types of saws. Some models come with a folding stand that is on wheels which makes it very easy to move or reposition without having to lift it all the time. Even though it is relatively light, constant lifting can become tiresome. You can mount these on your workbench which will give it more stability and could possibly reduce the amount of vibration as well. These smaller table saws generally have a 1 hp motor or even smaller and can run on a normal household circuit with no issues.
As with anything, it’s easy to get overwhelmed with the variety of types, sizes, features, colors, weights, what, when, why, where, who…(let me catch my breath). For now, let’s focus on what’s right for you with our Best Portable Table Saw Guide. We’ll start by identifying quality brands that align with your needs. Besides, who wants to buy something that won’t work?
When it comes to Japanese engineering, Makita are known as a name to be trusted. With that in mind, you can likely imagine what the Makita names in the eastern world, but that doesn’t mean that their products aren’t well suited for use in the United States and other western countries too. The company was formed from a small shop in Nagoya, back in 1915 and since then has expanded across the globe, selling their products in over 150 countries, but still managing to maintain their ethos of good quality.
We put our hands on 10 of the most popular table saws and tested them for accuracy, power, and functionality. It took some time, but we have some fairly conclusive results. Table saws are undeniably the kings of rip cuts on the jobsite and in shops. The concept is simple: Place a motor below a solid table to turn a blade somewhere in the 4000-5000 RPM range through the surface and watch the sawdust fly. The idea may be simple, but the reality is much different. How big should the table be? What size blade should you use? How heavy can you get away with making it? For this shootout, we’re looking specifically to find the best portable jobsite table saw.
Contractors who do a lot of finishing work and interior/exterior trim work know the value of a good portable table saw. DeWalt has built the DWE7490X from the ground up as a stable and safe job site cabinet saw that can be used to make those precision cuts quickly and easily without the need to pre-fabricate materials and then bring them to the job site for final fitting.
To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.
Dust collection can seem like an afterthought for jobsite table saws. The fact that you’re outside, often on an unoccupied site, negates the need to collect your dust. But breathing that stuff doesn’t do your lungs any favors. That’s why dust collection is so important. Of course, if you’re working inside or in an occupied structure, collecting all that dust will make the cleanup part of your day easier to deal with. Since we’re not talking about concrete dust regulations, even a standard shop vac will be a good bet to help contain the mess.
I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!
Under the table, you’ll find plenty of space to store away your accessories. This is valuable if you’re working on site and don’t want to keep hunting down bits and pieces. You’ll be able to stash your arbor wrench and Allen wrenches close to hand. The rip fence also flips upside down and can be stored under the table. It’s this kind of attention to detail for a jobsite saw that’s always appreciated.

It’s a little extra assembly work, but you’ll be grateful you did it later. The blade guard will keep your hands away from the saw and the splitter will help to reduce kickback from the machine and keep the wood flowing smoothly through the table saw. Additionally, if you’re working to cut thin boards, you should use a push stick or a push shoe to make sure your hands stay guarded while you work.
The Craftsman table saw is one of the most compact of the bunch when it’s folded up. And if you can get it for the sale price of $260, it’s also the cheapest of the best table saw options. The blade guard and anti-kickback pawls are identical to the Porter-Cable and are the hardest of any of the saws to install. And they are the only two blade guards that don’t have a feature to hold them out of the way when you’re adjusting the blade or setting up the cut.
Thanks for the work you put in on this. I am retired now and have been researching these types of saws as I wish to begin doing some building of storage shelves and deck furniture. As a beginner, I did not wish to spend huge amounts of money until I was sure it was something I would be staying with for a while :-). Very informative and happy to see the way you did your testing (on the video). I spent 20+ years testing or working with security software testers and totally understand the issues of testing (almost anything) in a fair and honest way. Your work is greatly appreciated!.
Delta 36-L336 3 HP Motor Uni-saw with 36 Delta 36-L336 3 HP Motor Uni-saw with 36 in. Biesemeyer Fence System is ideal for woodworking cabinet making and boat building. It features speedometer style scales and a 36 in. Biesemeyer fence. The 3 HP 230-Volt motor cuts hardwoods and engineered products like MDF and melamine. The riving knife enables ...  More + Product Details Close

One of our favorite features, however, would have to be the built-in safety system. The safety system quickly detects when human contact has been made with the blade by reading the electrical signals that are sent throughout the blade and locks down on the cabinet within milliseconds.The whole process only takes about 1/200th of a second and helps to save craftsmen from devastating injuries every day.
The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.
Another indication of how hard a table saw is working is monitoring the amperage (AMP) draw under loading conditions. We measured the amp draw for each saw using all three materials again at the same time we were recording RPMs. The first graph below shows the amp draw for each saw cutting plywood compared to the no-load amp draw. The white bar on the left indicates the no load amps and the colored bar on the right shows the maximum amp draw during the cut.
Apart from some short reviews, we’ve also covered some other aspects such as safety and proper use of these tools. Make sure you thoroughly read our articles because they could save your life. The tips we offered are well-known among the professionals, but beginners are always susceptible to various risks, especially if they don’t know how to handle these tools properly.
If you are interested in buying a new model, then do not hesitate to read the following lines. Before making a purchase, you need to consider several things. Rip, miter, bevel and cut are just some of the things you will be able to do with this tool. More than that, you can amplify its functionality by adding several accessories to it. As compared to traditional saws, the circular saw has the ability to move the material towards the blade, which means a much more precise cut. However, in order to help you find a unit that meets your requirements, here are some of the most important things to look for.

When you need to change the blade, you’ll find that this saw comes with an arbor lock that you can unlock with one hand, which lets you change the blade without any special equipment. It uses a poly-v drive belt system that gives the motor extra power, but this belt system also reduces the noise of the motor, which makes it great those working around others.
Choosing the best portable jobsite table saw wasn’t an easy task but we’re confident we’ve done a thorough evaluation. In a very close race for the best table saw Hitachi beat out the DEWALT which came in second place followed by Skilsaw in third and Makita in fourth. It’s very interesting that the Hitachi and DEWALT look extremely similar. Hitachi edged out the DEWALT in performance and price resulting in the final scores. Skilsaw beat out Makita for the 3rd place only slightly and that result is really a function of pricing.
Choosing a circular saw is a daunting task because the market is overflowing with powerful tools designed to help you cut different hard materials. As it was mentioned above, there are plenty of factors you need to consider when making a purchase and the size of the unit is one of them. As compared to small tables, a large unit provides you with more space where to cut a large sheet of plywood. However, if you don’t have enough space to place the table, you can add an extension table to a smaller unit. It can be mounted to the side of the unit and removed after use.
You have to know the amount of money you are willing to spend for the right saw. The truth is that the price will vary significantly depending on where you are buying the saw, the brand and the features it comes with. However, with a good budget, you can easily narrow down the options you may have. You will have a smaller range to work with and you will know what features to expect within that price range. Always be willing to spend a little more on the table saw you want in your workshop especially if you work on wood every day.
The Skilsaw SPT70WT-01 is a super high quality table saw with the power to match. The Diablo blade that comes with it will cut through 4×4 without any problems at all, like a knife through butter! One of the best features we noted was the fact that there is barely any vibration, this allows to you to cut as straight as an arrow, you can really feel the build quality with this saw.It has an extremely easy to use miter gauge, just a flick of the wrist to change the angle of cuts to exactly what you want.
The DeWalt DWE7499GD table saw earns a third place finish in the safety category thanks to their GuardDetect technology. This doesn’t prevent you from using the saw without the pawls and blade guard in place, but it does require you to physically indicate you are aware they’re not in place. Ideally, this gives your mind one last opportunity to consciously note the additional care that needs to take place before cutting.
The same fence system that comes on our number one choice, which lets you change the angle of the wood and make various cuts, also comes on this SawStop ICS31230-52 3HP 230V 60Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System. Designed use in any type of work space, it runs quietly to let you do your work without disrupting others, and it features the same safety system to shut down the saw when it touches any skin. Weighing more than 700 pounds, this is the type of cabinet saw that you can use in the same spot years.
After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.
Setup was nearly as simple as SawStop’s with just a narrow margin between them. We only needed to attach the handle and bolt the saw down to the stand. The stand is a gravity rise style, but requires you to bend down to ground level for collapsing and extending it. It’s a reasonably solid platform, though a lot of movement throughout the day will leave your back sore.

One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.


Like most other product review sites, ConsumerSearch is supported by a combination of commissions on the sale of the products we recommend and ads that are placed on our site by Google. If you find something you like, you can help support us by clicking through and buying the products we pick. Our editorial process is independent and unbiased; we don’t accept product samples, requests for reviews or product mentions, or direct advertising.
These are only a few of the products that you’ll find we’ve reviewed across the website. If you still haven’t found your perfect table saw, we can guarantee that you’ll find a product that works for you by exploring our table saw reviews. We know that everybody’s needs are different when it comes to table saws, which is why we’ve reviewed a range of products.

As the name indicates, it has a V-belt and a pulley system through which the power is transferred. Given the much higher torque and power, these drives are more suited for heavy-duty sawing jobs, providing better efficiency when cutting thicker wood variants. Additionally, a belt drive throws up much less dust as the motors are mounted far away from the blade. I would say other than that; they are less safe and more costly.


We rotated the blade to the rear of the saw to enable the dial indicator to contact the same location of the same tooth behind the carbide portion. We positioned the dial indicator to the rear of the saw placed onto the blade and the reading recorded. If the blade and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading.
The differentiating factor is workshop realestate: it takes up nearly 2 square feet less space than its larger, more powerful counterpart, making it ideal for craftsmen with less workspace who don’t need the extra horsepower for cutting heavier hardwood materials. Best of all, it includes SawStops 5 millisecond safety system to protect craftsmen from accidents that can lead to serious and permanent traumatic injuries.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
Furthermore, the split guard offers a tool-free riving knife that moves freely via a front level control for on-the-fly adjustment. Pawls and splitter guards can also be added to the riving knife without the need for tools as well. Best of all, the 36-L352 includes a 52-inch Biesemeyer Fence System that has an integrated tape and a hairline pointer for consistent and repeatable cuts every time. If you don’t work with wood that needs the additional horsepower of 36-L552, this version of the Delta UniSaw is definitely for you.
Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.

Each one has different power, capabilities, mobility and price points as well. If you’re not sure which type you need, we have outline some specifics on each below that will help you choose. When you begin the search for your table saw, you will need to know the answers to a few questions that will narrow down the choices for you and make choosing much easier.


Balancing heavy-duty durability and lightweight design, this machine proves that good things can come in small packages. While buyers are overall happy with their purchases, they do seem to all agree on one thing: the DEWALT DWE7480 may be an overall investment, but it could seriously do with a miter gauge replacement. Buyers report replacing its inaccurate, plastic gauge for a solid, more detailed one.
In terms of the safety features that you’re going to want to look for in your table saw, one of the most prominent includes a flesh sensor. This is basically designed so that the table saw will immediately stop operating after 0.01 seconds of coming into contact with flesh. This means that if the worst should happen and you come into danger as a result of using a table saw, the damage will be kept to a minimal. As you can likely imagine, this particular safety feature will push up the price of the table saw by a small amount, but it’s definitely a feature that’s worth happening if you value your safety whilst using power tools.
With a three-horsepower motor inside, this SawStop ICS31230-36 3HP 230V 60Hz Cabinet Saw Assembly with 36-Inch Industrial T-Glide Fence System is suitable most of the jobs you have in mind. Its industrial T-Glide fence system lets you make all the cuts you need, and the extension table gives you more room to work too. It also features a system that locks the wood in place to ensure that you make the accurate and completely straight cuts that you need.
The bench table saw is the least expensive of the four types of saws. Some models come with a folding stand that is on wheels which makes it very easy to move or reposition without having to lift it all the time. Even though it is relatively light, constant lifting can become tiresome. You can mount these on your workbench which will give it more stability and could possibly reduce the amount of vibration as well. These smaller table saws generally have a 1 hp motor or even smaller and can run on a normal household circuit with no issues.
To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.
One of the lightest and most compact table saws was also the most stable: Skilsaw. There’s no wheel base to the stand and the outward angled legs provide a wider platform than it may appear against its colleagues. In second place was DeWalt, also offering a wide platform, but without the amount of rigidity that Skilsaw has in their stand. Coming up in third was Bosch with its gravity rise stand followed closely by Ridgid. It’s important to note that none of the professional class table saws had any stability issues inherent to their extension locking—it was all in the stand.
Today's table saws also include riving knives, which ride up and down with the blade when its height is changed, rather than splitters that are fixed in place. The problem with the old splitters was that they had to be removed for certain types of cuts, and users might forget to put them back on before making rip cuts. This increased the risk of kickback injuries, which occur when the spinning blade kicks back a piece of wood toward the user with tremendous force, causing serious injury to any part of the body that's hit.
As accidents and injuries are common when using large power tools like this one, it’s important that you look for safety features such as a dust collection system. Inhaling the sawdust that comes off the wood can make you sick, but this system does a good job of removing the dust from your work area. The collection port itself has a convenient on the cabinet too.
When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.
Self-Aligning Accuracy – As well as power in your table saw, you’re also going to want it to be as accurate as possible. We can comfortably say that this table saw from Bosch achieves that formidably with its self-aligning accuracy. This basically means that the square lock rip fence aligns itself for accurate performance. If you’re going to be using your table saw regularly and know that you need to get the job done correctly, this will provide it.
The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.

Before we get into some of the top features, we want to take a look at the design of this cabinet. As it uses an enclosed cabinet, you’ll find that the motor lasts longer because it doesn’t wear down due to constant exposure to dust. This cabinet also features convenient hand wheels on the front and sides that help you make quick adjustments before cutting or as you work.


I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.
×