Safety Features: All said and done, you have to accept that the portable table saws are amongst the more dangerous tools to operate. If you are not careful, you can easily get hurt. This makes the safety features some of the most important to consider. I would keep an eye out for features like anti-kickback pawls and blade tilt as they go a long way in avoiding accidents. Most also come with a magnetic switch that makes sure that the machine does not get started on its own accidentally. This is essential. Do not buy a portable table saw without a magnetic switch.
With that in mind, you can likely imagine that hybrid table saws are perfect for those looking for greater power than that offered by a contractor table saw, but don’t fancy paying anything around the price of a cabinet table saw. At the same time, whilst hybrid table saws are nowhere near as portable as some of the aforementioned options, you should still be able to find that they can be transported when necessary. When it comes to the middleman of table saws, that’s a title truly deserved by the hybrid variety. In all, if you’re looking for a bit more power than that offered by a contractor table saw but don’t fancy paying the price of a cabinet variety, this is an option well worth your looking at.
Love the video. It was very helpful, answered some of the questions I've had and wondered if you can expand this a bit further. I have a Thomasville bedroom set that I bought in 1981. After all of the years of my wife using hairspray, there's a layer of it on the bed's foot board and the top and leading edge of the dresser. Will this technique remove the hair spray and restore the finish? I tried using denatured alcohol to clean it in the past but stopped short of using a sanding pad or working it to the point that nit was anything but tacky. Sounds like I didn't work it long enough. Am I right or do I need to do something else? These areas are the only bad spots on any of the 5 pieces of the set. Thanks!

If you are new in this industry, you need to know one important thing. Every model is equipped with a motor. The amount of power and the motor are strongly related to the project you have. In simple terms, it depends on what you are cutting. For example, a 2 hp motor can easily rip wood of 2 inches thick, while other hard materials require a 5 hp motor. Keep in mind that the 5 hp motor is found only on cabinet saws.


Another good table saw from Powermatic is its 1792006K Model PM2000 5 HP 3-Phase Table Saw with 50-Inch Accu-Fence System and Rout-R-Lift. The dust collection port moves much of the debris you produce away from your work area, but the cabinet itself has a sloped design that makes it easier to get under the cabinet cleaning. Its quick release riving knife not only reduces kickbacks but also reduces the risk of the knife binding.
With a riving knife that has a quick release design that makes it easier to change, it’s no wonder that this Powermatic 1792017K Model PM2000 10-Inch 5 HP 1-Phase Table Saw with 50-Inch Accu-Fence and Workbench is so popular with shoppers. That knife also has built-in kickback prevention that will keep your hands safe and help you focus on your work. Though it’s just as sturdy as other cabinet saws, this one comes with a caster system that allows you to move the saw across your shop.

I appreciate the helpful comparison of the best table saws. I’m fairly new to woodworking, and until recently I was using an old table saw that used to belong to my dad. Long story short, it’s no longer usable, and so I’m looking for a good table saw to buy that’s beginner-friendly. I have my eye on the DEWALT DW745 – evidently it’s really popular and does a great job. I’ve taken a look at some other sites for more ideas. Your guide here is great. What is your opinion on the DW745?
Still featuring the T-Glide Fence System for smooth, safe operation without compromising on precision measurements and secure locking for repeatable cutting, the TGP236 is still an exceptional cabinet saw in its own right Furthermore, the blade height and angle are still fully adjustable via the comfortably large hand wheels on the front and side of the cabinet itself.

If you don't need a stand, a benchtop table saw can be an economical and practical choice. The DeWalt DW745 (Est. $300) isn't covered in any professional tests, but it gets excellent reviews from users. This saw is limited somewhat by its small size, as it has only a 20-inch rip capacity and can't make dado cuts. Nonetheless, it earns very high ratings at Amazon with an overall rating of 4.6 stars based on nearly 2,000 reviews. Meanwhile, the more than 600 that weigh in at Home Depot like it even a touch more, granting it a rating of 4.8 stars, with recommendations from 98 percent of users. Owners like its rack-and-pinion fence – the same design found on the larger DeWalt – which they say is accurate and very easy to adjust. Its light, portable size (just 45 pounds) is also a plus. However, like the DeWalt DWE7491RS, it gets a thumbs-down for its flimsy, awkward miter gauge and occasional quality-control problems.
The blades of a circular saw are usually divided based on several factors, including diameter, arbor size, speed, application, and well as number f teeth and materials used in their construction. Most tools are equipped with 10 or 12 inches blades. This is the medium size, but there are also models that come with blades as small as 5 inches or as large as one hand. Since they are able to cut various different materials, including the most solid ones, most models have carbide or carbon blades. You may also find diamond-tipped teeth blades, but they are a bit more expensive. The number of teeth is usually between 24 and 80 and you need to decide whether you want a saw with left or right tilt. The direction in which the blade tilt is very important and it can provide plenty of advantages.
The blades are categorized according to number of teeth, diameter, arbor size, kerf size, application and speed. They can also be divided by material. Regular commercial table saws are 10-inch or 12-inch. Teeth usually number from 24-80. Many blades are tipped with diamond, carbon or carbide. This lets you cut through more than just wood. You will also need to think about the tilt of the blade. They are available in left tilt or right tilt. With a left-tilting hybrid or cabinet saw, the motor cover can get in the way of the sliding table. Router table extensions don’t work well on left-tilting saws. 

While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.


Though this Jet 708674PK XACTASAW Deluxe 3HP Cabinet Saw comes with the same three-horsepower motor found on the last cabinet saw, it comes with a shorter 30-inch rip fence that may be a little too short some of your projects. It features all the same great features that made Jet so popular with contractors, including a cast-iron enclosed cabinet that stops dust from entering the motor and a poly-v drive belt system that runs more quietly than other belt systems.
June 7th! Leather couches (3), storage ottomans (2), queen & single beds, kitchen table & chairs, gliding chair, lamps, end table, washer & dryer, gas blower & weed whacker, 50 in Plasma TV, 19 & 12 in TVs, desk & shelves, metal fire pit, outdoor iron table & 2 chairs, outdoor porch swing & stand, circular saw, jig saw, sander, other assorted goodies! Cash & carry! 972-436-0328

Under the table, you’ll find plenty of space to store away your accessories. This is valuable if you’re working on site and don’t want to keep hunting down bits and pieces. You’ll be able to stash your arbor wrench and Allen wrenches close to hand. The rip fence also flips upside down and can be stored under the table. It’s this kind of attention to detail for a jobsite saw that’s always appreciated.
If you’re going to be working with a table saw, you’re going to want to make sure you take a few safety precautions before beginning your work. Sharp, heavy duty tools like a table saw must be handled properly and treated with respect in order to see the best results and maintain a safe environment. Click here to find out the best way to sharpen your blades. Before you begin your safety preparations on the table saw itself, you need to take the time to make sure you are properly dressed for your task.
Table saws that can be found on the market are designed for different uses. There are four types that these table saws can be listed under. There are Portable saws, contractor saws, hybrid and cabinet saws. When exploring the possibility of a new saw you will need to understand what each of these mean and how each saw performs in their perspective class.
The cabinet saws are the most powerful woodworking machines. They are durable and strong enough to resist for a long period of time. Most people prefer them because of their impressive features which make them precise and extremely accurate. The motors of these units usually run on 240V and produce from 3 to 5 hp. As mentioned before they are very heavy. Most models weight more than 500 pounds, however, this makes them very stable.
Even a newbie can go around the table saw section at the local home improvement store and feel that some saws have easier adjustments than others. Some are simply easier while others are downright innovative in various ways. Porter-Cable came out of the value group for the overall win with adjustments that are both smooth and intuitive. Dual adjustment wheels mean that you’ll be able to accurately adjust your blade height and your bevel angle—a feature no other saw in this group has.
Another good table saw from Powermatic is its 1792006K Model PM2000 5 HP 3-Phase Table Saw with 50-Inch Accu-Fence System and Rout-R-Lift. The dust collection port moves much of the debris you produce away from your work area, but the cabinet itself has a sloped design that makes it easier to get under the cabinet cleaning. Its quick release riving knife not only reduces kickbacks but also reduces the risk of the knife binding.
Every professional woodworker probably knows that portability and durability are two of the most important factors of every high-end table saw. There are dozens of types and models available for sale, but only a few are worth checking out and investing in. However, the SKIL 3410-02 is one of them. It is made of heavy-duty steel and features a 20-inch x 26-inch cast aluminum table that extends to 20-inch x 32-inch for larger projects. The motor of this tool is quite powerful. It comes with a 15 amp motor that is capable of cutting different types of wood. Its miter gauge is precise and delivers accurate cuts and the price is more than acceptable. Additionally, it is equipped with an EZ view measurement system thanks to which it can provide accurate measurements and cuts. The table measures 28.9 x 20.9 x 13 inches and weighs 67 lbs. Compared to other similar heavy-duty tools, it is lightweight and portable so you can place it wherever you need it to complete your projects.
At this point, you are wondering why this is not number 1. The problem is with all that power, precision, and all those great features; you can get only 18 inches of cut from it. This severely impacts the usability of the product. While it can still be used for some home based products, its use in a professional setup is fairly limited to smaller projects. It also only has a one year warranty which is pretty light.
The compact saws are a bit more advanced than the bench top saws. They are equipped with plenty of impressive features and characteristics including direct-drive motors. In spite of their lightweight feature, most compact saws are powerful and provide a lot of benefits. With additional features like stands and extra surfaces made of cast iron, most of them resemble full-size models. However, they still have a rip capacity much smaller than other saws.
The last one in our list of the top portable table saw picks is another offering from Bosch. If you are looking for a sleek and extremely portable table saw, then this is for you. It weighs merely 52 pounds and can be easily carried around anywhere that you might go. The ergonomic grip and the uniform weight distribution further enhance the portability aspect.
In addition, a top-quality fence should move smoothly and have a scale that’s accurate and easy to read. Our favorite is the DeWalt fence. The rack-and-pinion system keeps the fence parallel to the blade, and the micro-adjusting knob allows easy and precise fence positioning. Runners-up in this category for best table saw are the Ridgid and Bosch saws. They both have superb fences, with the added advantage of T-slots for attaching accessories like featherboards.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
Dust Collection Port – Using any table saw is guaranteed to generate an awful lot of dust and anyone who suffers from asthma will know this to be a big problem. With that in mind, it’s nice to see that DEWALT have taken precautions to allow you to properly extract dust when using your table saw. This is through the product’s 2-1/2-inch dust extraction port that allows you to quickly and easily connect a vacuum for efficient dust extraction. If you’re going to be regularly using your table saw, you’ll definitely notice the advantage of having dust automatically extracted out of the environment for you.
Table saws are very efficient tools that have proven their worth to woodworkers and DIYers alike. They enable people to cut down and craft wood much more efficiently, but there are a few things you should know about proper use of a table saw before you begin if you want to achieve the best results. The first is to use the blade guard and log splitter to make your work easier to accomplish and a more safe environment.

All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.
The blades are the primary factor to consider when shopping for a saw as they hugely determine the performance of your table saw. The blades will only be effective if they are set at a correct depth of cut. The table saw will also perform best if only the correct blade for the cut is fitted, as a proper blade will enable you to achieve a precise and smooth cut. When purchasing a blade, go for the one with a correct setting blade. Consider the cutting depth also as this will determine its suitability for the job. You should also ensure that the table saw is equipped with splinter guard as this will help in minimizing splintering of the board’s top surface. Splinter guard also enhances accuracy because when it is lined up at the start and finish mark the saw will cut with precision. A suitable table saw should also have a 20mm arbor as this guarantees the stability of the blade and hence, safety in the workplace.
The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25" ripping capacity, meaning tearing through thick sheets of plywood has never been easier.
While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.
Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.
We went through a large number of portable table saw reviews to help you identify the top options that you could choose from. If you do not have the time to surf through hundreds of options available online, this list will make the task easier for you. Of course, you can also use our buying guide to sift through options outside this list. In saying that, let’s get started with our top pick, the DEWALT DWE7491RS!
To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.
A cabinet table saw is so named because it has an enclosed style base. This saw is the opposite of the contractor saw. Cabinet table saws are designed to be functional and lasting to meet the qualifications that are required by people who work with wood for a living. They are constructed to be more durable than contractor saws. Makita table saw offers many popular options at a very affordable price.
1. Is it possible that the SkilSaw SPT99-11 and SPT99-12 have the ability to accept up to a 13/16″ dado set instead of just the 1/2″ max your review states? I have seen the larger spec stated elsewhere. If not, why? Is the arbor just not long enough? Or is it a zero clearance plate problem? I can’t imagine having to do two passes to complete a 3/4″ dado. The 1/2″ max seems a weird anomaly as compared to all other saws in the class.

Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.


Some of the key table saw brands included Dewalt, Bosch, Makita and Ryobi. You’ll notice that we’ve featured a number of these brands across our table saw reviews. You’ll also find that these different brands offer something very different in terms of their features and functionality. With that in mind, we’ve put together a comprehensive summary of those brands on this very page and you’ll find more detailed information about them across the website and also information about choosing the best brand of table saw for you.
A lot of the modern table saws nowadays will have a dust collection port where you can hook up a vacuum or extraction system to it. We would always recommend that you purchase a table saw with a dust port, always check the size of the port to make sure it fits with either your vacuum or your extraction system, or you can always modify something to make them fit.
Portable table saws are made to easily transport, making them a perfect utility saw for carpenters. Portable saws function exactly the way a big table saw works. The difference is the portable table saw does not have the huge motor as the types of saws. Because they use the smaller motor, they are not as powerful and are also loud. They are less durable and are not as stable as the larger saws. One good suggestion for a portable table saw is the Ryobi Table Saw.

Framing work is full of rougher cuts that rarely makes use of more than one blade at a time. But occasionally you might need dados for an onsite custom build in. If that sounds like you, be sure to find out the saw’s dado stack capacity. It requires a longer arbor and you won’t be able to use your normal throat plate for it. Some manufacturers offer a dado throat plate if they have the capacity for it.
With a cutting speed of at least 4,500 RPM, nothing will hold you back from getting the job done in minutes. Hitachi job site table saw is designed to give you freedom in your work and the ability to manage your time. Keep every minute accountable by investing in the right tools for your workshop. However, during different occasions, you will have different materials both in size and texture. During such moments, you will require adjusting the fence to accommodate your material and cutting style. This job site table saw is designed with an adjustable feature to ensure your precision and accuracy is not compromised. The low power consumption makes it easy for you to maintain the saw and enjoy smooth and accurate results at no extra cost. When it’s not in use, the table saw has fold and roll stand that guarantees you space saving and convenient storage. The foldable design also makes it easy to transport from one place to the other comfortably.

Table saws will continue to be popular and much sought after tools in any workshop or construction site. There are many terrific styles on the market which is why it is important to do some research and look at the reviews provided here as well as the tips contained in this guide to help you choose the right table saw for your needs, whether you are a professional or a DIYer who loves to work in the workshop making things for enjoyment.

You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
Located right next to the hand wheel on the front is a panel that features both a power button and a stop switch. The power button helps the motor come to life quickly without requiring that it heat up first, and you can press down on this button to turn the saw off at the end of the day. The emergency stop switch helps you stop the blade in the middle of a project to prevent accidents caused by clothing or skin coming into contact with the blade.
We found more than 1,000 reviews for this saw at Amazon, Home Depot, and Lowe's, with ratings averaging around 4.6 stars. Owners love the gravity-rise stand and accurate, easy-to-use controls. They also describe the saw as solidly built and easy to set up. Reviewers are mixed on the issue of dust collection; many users complain that the saw produces a lot of dust, but Woodworkers' Journal reports that most of the dust "routed neatly through a shroud that surrounds the blade" and out to a vacuum cleaner.

Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Table saws in this best table saw review run the gamut in price and quality. You can buy a table saw for as little as $150, and if you use it just to occasionally rip a board, that may be all the saw you need. If you want a saw that’s easy to carry and you don’t need to rip sheets of plywood in half, look for a “compact” saw like the DeWalt DW745 (shown) or the Bosch GTS1031. If you have room for a little larger saw that’s slightly less portable but capable of wide rips, consider one of the best table saws we review here. And finally, if you want to build cabinets or furniture and have a big enough work area, you can step up to a stationary contractor’s saw like the Ridgid R4512 (shown), for about $650.
×