Above are the results for RPM Blade Speed while cutting 3/4″ plywood. In the left column is the no-load blade speed and the right column is the lowest recorded blade speed during the cut. The drop in blade speed is fairly small ranging from 6% for Hitachi and Ridgid, 7% for Makita and SawStop, 9% Bosch, 11% DEWALT, 14% SkilSaw, and 24% for the Delta.
One term you may hear when reading about table saw accuracy is blade runout. Runout is a term that describes whether or how much the outside edge of a saw blade wobbles while being held by the motor shaft. Sometimes, operators measure runout by using a saw blade. In that case, the very use of a saw blade presumes that the specific blade is perfect or nearly perfect in its flatness. Using a saw blade that has any warping will not give a clear indication of blade runout.
Patrick – Thanks for the feedback. Trust me, I wish we could spend more time on every aspect but we spent hundreds of hours as it was. I can tell you that the rack and pinion fences are much better than the standard fences of the past. Our entire group felt strongly that we’d prefer the rack and pinion on all the saws. We felt the Ridgid and Delta fences were the least impressive of the standard type.
I have another post for Woodsmith magazines. ShopNotes 2.00 each copyIssue 1 Premiere Issue Shop -- Built Router TableTable Saw AccessoriesTips for Accurate CrosscuttingElu Router ReviewIssue 2Wooden Joiners MalletStorage Bin SystemHand-Cut MortisesRadial Arm Saw FenceIssue 3Handy Tool Carry-AllShop-Built Cling StationPlate Joinery TechniquesAdjustable Grinding JigIssue 4Shop-Built Panel SawThi...
While your table saw is unplugged, take the time to clear and clean the work surface, removing any debris that could negatively impact the smooth path of the wood you will be cutting. Then, lower or raise the blade to where the blade gullet (the curved section between each blade tooth) is equal with the top of the piece of wood to be cut. Also, make sure that your saw's dust exhaust port is clear and open and that a bag is in place to catch any excess sawdust.
I recently brought the Ryobi RTS21G after my dwe745 got stolen and actually couldn’t believe the quality! You guys were definitely right about using the Diablo blade, makes a big difference as it’s not the most powerful table saw in the world, but really didn’t expect much for $200 but i was very surprised. Anyway just wanted to say thanks for the great review and recommendation!
The table measures up at 29 inches by 21.5 inches. The 4100-09 is not suitable for dealing with large stock or sheets of wood. Made from aluminum, you’ll meet with no resistance as you slide the timber toward the blade. The only negative with the table is the way it’s finished with an anodized coating. This is fine to start with but tends to wear over time, something that doesn’t just look unsightly but can ultimately affect accuracy. This is a surprising oversight from Bosch and one we hope they rectify in future iterations of this fine table saw.
One of my favorite features is the folding fence which essentially increases the surface area of the table to be able to handle larger projects. For instance, I ripped full size 4ft x 8ft sheets of plywood for a home remodel project and the Rockwell Table Saw performed flawlessly. I couldn’t have completed that particular project without the foldable fence extensions.
Hitachi C10RJ 10 in. job site table saw features a powerful, industrial grade 15 A motor that operates at 4,500 RPM, giving you the ripping power to cut through even the toughest woods. This Hitachi table saw has a 0-45 degree bevel and height adjustments. One of the best features is its large work table which also has a telescoping extension, allowing rip cuts up to 35 in. wide! When you pair the power of this table saw with the bevel range and table size, you’ll be able to power through any project you throw at it! Other great features include: front mounted controls, oversized controls, integrated safety switch, and a soft start function that helps decrease recoil at startup.
Ridgid notches a third place finish as the only saw to include an independent blade height lock. The adjustment wheel raises and lowers with multiple full turns like most saws, but integrates a lock into the center. For the bevel adjustment, the outside of the height adjustment wheel turns a rack and pinion style system to accurately change the blade angle – a feature Makita shares.
The 15-amp motor is outstanding, developing up to 4HP and operating at a speed of 3650RPM. This is not quite as pacey as the DeWalt but still more than respectable. The other advantage to this motor is that – for a table saw, at least – it’s pretty quiet. Noise isn’t such an issue out on the job site but if you’re woodworking at home, the quiet motor is a real boon.
Delta has also improved the tabletop geometry on this model which means that you’re going to get more surface area stabilization. The base is also made of durable cast iron and since it offers easy access to the off/on switch, using the Delta UNISAW is a breeze. Other user friendly features include the convenient dust extraction system, large blade opening for easily changing the blade and fine-tuning the riving knife, smart storage for simple organization and fast access.

Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.
×