In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.
Contractors who do a lot of finishing work and interior/exterior trim work know the value of a good portable table saw. DeWalt has built the DWE7490X from the ground up as a stable and safe job site cabinet saw that can be used to make those precision cuts quickly and easily without the need to pre-fabricate materials and then bring them to the job site for final fitting.
We took all of the data from the RPM and AMP measurements and added them to come up with the final performance rankings. For each saw we added up the total percentage decrease in RPM’s (for each material type) and added that to the total percentage increase in AMP’s (for each material type). This gives us a relative comparison of each saw over all 6 sets of data.
Every woodworker knows the plague of working in a dusty environment. The SawStop has a fantastic dust collection system so you can enjoy your cutting without your eyes being strained. Almost all of the dust is wicked away both above and below the table. Up above, the blade does all the legwork and there’s a neatly designed shroud which pulls all this dust away from the blade. The 4-inch port means you can slip your shop vac on with no issues.        
As we said in the beginning of this section, many of these saws will be used, right out of the box, for rough cutting materials and the fine accuracy may not matter so much in that application. If this is the case for a saw, the quality of the cuts and more importantly, the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer. So, TBB wanted to see how the various saws compared right out of the box. The results are in and, as a group, these eight saws measured up quite well for out-of-the-box accuracy.

The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.


Choosing a circular saw is a daunting task because the market is overflowing with powerful tools designed to help you cut different hard materials. As it was mentioned above, there are plenty of factors you need to consider when making a purchase and the size of the unit is one of them. As compared to small tables, a large unit provides you with more space where to cut a large sheet of plywood. However, if you don’t have enough space to place the table, you can add an extension table to a smaller unit. It can be mounted to the side of the unit and removed after use.
With a three-horsepower motor inside, this SawStop ICS31230-36 3HP 230V 60Hz Cabinet Saw Assembly with 36-Inch Industrial T-Glide Fence System is suitable most of the jobs you have in mind. Its industrial T-Glide fence system lets you make all the cuts you need, and the extension table gives you more room to work too. It also features a system that locks the wood in place to ensure that you make the accurate and completely straight cuts that you need.
Jet has a strong reputation for providing customers with durable power tools that operate just like professional models but cost less, and that is definitely true of this 10-inch table saw that comes with a riving knife. You’ll like the basic design of this model, which has an intuitive design that allows you to set it up and start cutting faster. It features both a solid cabinet as well as an extension table that stretches out from one end.
The power transfer system is neatly done. The model features a serpentine belt which is quiet and smooth during operation. Therefore, the level of noise is satisfactory. Precision is something that makes this model worth checking out. Whether you’re a professional or a beginner, you’ll definitely appreciate the accuracy of this model. On the other hand, with great things come great responsibilities. Don’t forget to wear safety equipment!

Some craftsmen are looking for a cabinet table saw that has both a small footprint but doesn’t sacrifice performance when it comes to cutting and shaping hardwood. If you are that craftsman, then the Grizzly G0690 was built with you in mind. With a 220-volt 3 horsepower motor, this smaller scale cabinet saw is built to rip and split some serious hardwood with minimal effort.

You’ll also find that the metal roll cage base will give you extra strength and durability to work with and the rear feet will enable you to adjust the height of the machine should you be faced with the challenge of working on an uneven surface. There’s nothing the DEWALT DW7480 Compact Job-Site Table Saw can’t handle. You’ll quickly be impressed by its ability to tackle any project you throw at it and learn to appreciate it for the great tool that it is.
Outfeed capacity is almost always the depth of the table. Pros using a jobsite table saw can opt to put a sawhorse or other support to hold the material after it passes the blade. There are a few models running around that give you some extra outfeed support, though. Most of the time, you’ll just have a buddy help guide the cut through from a safe stance on the behind the saw.
The bench top saws have a compact yet ergonomic design. Thanks to their lightweight feature, more and more people prefer to use them in their workshops. Despite the fact that they are not equipped with wheels, they can be considered portable, because they are very small. As such, they can easily be carried and transported from a place to another by almost anyone. Also, in comparison to the jobsite saws, the benchtop saws have a very limited rip capacity.
New, unopened in boxTraditional guard and riving knife system allows unlimited capacity for cross and rip cutsLightweight and compact design makes it easy to carry anywhere and sets up in seconds to cut wood, tile, plastic, metal, and aluminum Adjustable Miter Gauge for 0to 60angled cuts, right or leftSafety switch with key prevents accidental startAccessories included 1-miter gauge, 1-rip fenc...
To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.

And finally, they all include a blade guard that can be removed and reinstalled without tools. Because a few sawing operations, such as non-through cuts, require you to remove the blade guard, we like saws that make this task easy. The Bosch, DeWalt and Ridgid saws have well-designed blade guards that are easy to remove and reinstall. The blade guards on all but the Porter-Cable and Craftsman also have a feature that holds the blade guard in the raised position to allow better blade visibility for setting up cuts.
I just purchased this saw last week. It took several hours to assemble. everything was there and I had no problems putting it together. Not hard but time consuming. The first job was to rework some vertical drawers. It did a good job fence worked great as did the riving knife. Saw was quitter than I expected. overall I am very happy. The only problem was that I had to weight a couple of extra days for delivery due to all parts not arriving at the same time.
The blades are the primary factor to consider when shopping for a saw as they hugely determine the performance of your table saw. The blades will only be effective if they are set at a correct depth of cut. The table saw will also perform best if only the correct blade for the cut is fitted, as a proper blade will enable you to achieve a precise and smooth cut. When purchasing a blade, go for the one with a correct setting blade. Consider the cutting depth also as this will determine its suitability for the job. You should also ensure that the table saw is equipped with splinter guard as this will help in minimizing splintering of the board’s top surface. Splinter guard also enhances accuracy because when it is lined up at the start and finish mark the saw will cut with precision. A suitable table saw should also have a 20mm arbor as this guarantees the stability of the blade and hence, safety in the workplace.

While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
“The SPT99 table saw can accommodate dado cutting up to 13/16″ wide in a single pass. WARNING -To reduce the risk of injury, always disconnect plug from power source before changing blades. WARNING – To reduce the risk of injury, always use the Skilsaw SPTA70WT-DD 1/2 inch Dado Blade Table Insert or the Skilsaw SPT00A 13/16 inch Dado Blade Table Insert (both include dado accessory washer). Never make dado cuts without this insert. Do not use dado sets larger than 8″ diameter.”

This “review” is a giant nothingBurger. There is not one scrap of objective comparison between these saws. Because you sell them, they’re all great and will all zip right through “the hardest woods”. Bulll$hit. You did not test, compare, analyze, or use ANY of these saws. Re-hashinf manufacturer specs is a “Roundup” but it certainly is not a review. Typical sales pablum.


The DEWALT DWE7480 Compact Job-Site Table Saw is obviously a very impressive tool and in our opinion, it’s the best on the market. That’s why we’ve chosen it as our top pick. The design is built with the contractor in mind and helps to ensure that you’ll never have to worry about the machine breaking down on you in the middle of a job or not being able to meet your demands. The saw is fairly light weight (coming in at only 53 pounds) and is powered by an impressive 15 amp motor that has a 20 inch rip capacity.
With a single cast iron trunnion system, the Delta UNISAW offers dependable accuracy, smooth and continuous operation, but also vibration free control. Thanks to the fact that it features a fifty-two inch fence system, it’s the perfect choice for woodworking pros, but also people who are just starting out in the woodworking industry, such as hobbyists. Since it also comes with an upfront bevel dial to easily fine tune the blade level, you get a striking accuracy within a quarter of a degree, ensuring precision setups cut after cut.

Choosing the best portable jobsite table saw wasn’t an easy task but we’re confident we’ve done a thorough evaluation. In a very close race for the best table saw Hitachi beat out the DEWALT which came in second place followed by Skilsaw in third and Makita in fourth. It’s very interesting that the Hitachi and DEWALT look extremely similar. Hitachi edged out the DEWALT in performance and price resulting in the final scores. Skilsaw beat out Makita for the 3rd place only slightly and that result is really a function of pricing.
When you need a full size cabinet saw that can handle just about any woodworking job you can throw at it, the Powermatic PM2000 is the one for you. As with all high end cabinet saws, the PM2000 features box-style cast iron trunnions for that refined, precise feel when adjusting the blade angle and height. Front control wheels are user-friendly cast iron hand wheels that feature precision-machined center locking pins for making every cut consistent and repeatable.
It is safe to say that we live in a DIY era. Think about it. When was the last time you went on YouTube or anywhere else online and looked for something that tickled your fancy, a guide on how something is made or done, or maybe a tutorial. Indeed, we do it very often, so why should woodworking and home improvement be any different? With the prices of table saws constantly dipping and the insane number of choices on the market, you can get one for yourself and save thousands of dollars by doing things yourself instead of hiring contractors.
×