Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.
Other features include two handwheels with measurements around each one that you can use to set up your cuts or as you cut and an emergency button that acts like a kill switch to pull power from the motor during an emergency. This cabinet saw comes with an easy change system changing the blade and a warranty that covers the saw two years and the motor five years.
​The saw does not easily detach from the stand. Sometimes it’s beneficial to set the saw up as a bench-top saw, but the DeWALT 7491RS doesn’t come with quick release levers to accomplish this easily. In this case, you would have to use a drill to remove four screws to detach it from the stand. I wouldn’t recommend doing this unless you have to because over time the screw holes will strip.
Below we’ve included the current pricing (at the time of publishing this article). Pricing includes the cost of the stand and ranges from a low of $349 for the Hitachi to a high of $1,299 for the SawStop. The lowest price isn’t always the best in our opinion, we’re looking for the best value.  The Hitachi is an incredible deal at $349 and our top pick for price and value for a saw that has lots of power, a rack & pinion fence, and a solid stand.

Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.
TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.
Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.

The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.
We spent 42 hours on research, videography, and editing, to review the top options for this wiki. Regardless of whether you're a construction professional, a precision woodworker, or a DIY hobbyist tackling your next home-based shelving project, one of these handy table saws will help you get the job done fast. Our selections include models with durable cabinets, powerful motors, integrated fence rails, and even patented safety systems to protect you from on-the-job injuries. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best table saw on Amazon.
If you’re looking for one of the most powerful products on the market, you’ll find those such options within the 3-5 horsepower range. As you can likely imagine, these are products largely targeted at professionals looking to use their table saw on a day to day basis. If you’re a hobbyist or occasional contractor who doesn’t necessarily want to shell out a fortune on a table saw, you should find that between 1-2 horsepower does the job.
What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.
This article is the place to start, and then you can take it from there. My table saw buying guide has all the essential information on table saws you will need, like their classification based on size, portability, motor type, blade size, and the features they come with. You will encounter each of these terms in all the product reviews, which is why you shouldn’t skip reading it.
×