The DEWALT DW745 is a smaller version of the DEWALT DWE7491RS. It’s still a good saw in its own right. It comes with a 15-amp motor, just like the larger unit, though it can only handle rips of up to 20”. You’ll experience the same power and consequently, the same speed as the larger model, though you can’t cut pieces as large. This model is also meant to be moved, and while it doesn’t have wheels, it has a metal roll cage that will help it survive travel without taking any damage.
Great job with this testing. As far as the Hitachi. Many sources online point to minimal startups of the Hitachi c10rj before becoming unusable (not starting). The soft start module apparently doesn’t hold up. If it happens in 30 days it can go back to the store but after 30 days you call Hitachi (most described as unpleasant) drive to your closet Hitachi Service center and wait (up to months). I really like the Hitachi myself but am afraid of the soft start module error. THANKS FOR ALL THE GREAT WORK AND CONTENT. Please forgive any punctuation etc. This is tough on phone.
It’s worth remembering that contractor table saws are still going to be pretty portable because they’re designed to be used by contractors. That being said, unlike portable table saws, they don’t necessarily fold up into a compact position. This is largely because contractors tend to have the facilities needed in order to transport a larger bit of kit. The extra space that they take up in comparison to a portable table saw means that contractor table saws are able to offer a greater level of power and precision. Both of these points further support the fact that contractor table saws sit in the middle ground.
Lack of mobility is the cabinet saws major drawback. Some cabinet saws need proper electrical wiring set up and often weigh a huge amount because of cast iron table tops and full cabinet like stands. But if your setting up a new wood shop or have a work space or wood shop of your own then there is no better investment you can make other than purchasing a cabinet table saw.
Lack of mobility is the cabinet saws major drawback. Some cabinet saws need proper electrical wiring set up and often weigh a huge amount because of cast iron table tops and full cabinet like stands. But if your setting up a new wood shop or have a work space or wood shop of your own then there is no better investment you can make other than purchasing a cabinet table saw.

The fence on this system is easily the winner. With clamping on just the front side, it self-aligns better than any other in the group and offers excellent stability. While SawStop didn’t have the most powerful feel to the cuts, it was very smooth with little vibration. Feature preferences aside, the only (slight) negative we agreed on was that the bevel lock stuck a little bit compared to others.
This versatile option from Powermatic doesn’t require a 220 volt outlet in to provide sufficient power, making it unique compared to its heftier and more power hungry counterparts. Furthermore, it also features a full 60-degree range of movement for the blade bevel, allowing users to make clean compound miter cuts with minimal effort. Blade height and depth are controlled via the stainless steel wheels on the front and side of the main cabinet assembly, and the riving knife and anti-kickback guards and pawls can all be installed and adjusted without the need for tools.
The DEWALT DWE7490x 10 Inch Table Saw is an excellent tool for anyone, whether they need it for carpentry work or DIY projects. You’ll be able to complete your tasks with ease thanks to the superb technology and easy transportation. The device comes with powerful 15 amp motor and has impressive maximum depth capabilities. You’ll also be pleased with the 2 inch dust storage port that has a vacuum connection.
Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.
Some table saws come with a miter gauge, though the quality tends to be uneven. Some are great, and will serve you well for a long time, while others are flimsy or struggle to hold the correct angle or both. This is something that can most easily be determined by reading online reviews, though it’s always great to get your hands on a demonstration model, if possible.
When you purchase your table saw, more than likely it will have standard 10” carbide tipped blade that is good for general purpose use. This blade is capable of cross cutting a 4 x 4. If you replace it with a 40 tooth combination blade you will improve the quality of your cuts significantly and more than likely be much happier with the blade overall. You can get specialty blades also if you are going to be cutting other materials as well.
That being said, because of their portability, you’ll find that this type of table saw tends to be less powerful than other more permanent saws. This is because they have less power and less noise muffling too, so you’ll find them to be louder. What’s more, because of that aforementioned lack of power, you might find that you’re unable to use the law to cut through certain materials. This shouldn’t put you entirely off a portable table saw though. For many users, they offer the best of both worlds and provide the complete sawing experience that they need from their table saw. Portable Table Saws
2. The two models I mentioned above appear to only differ in the type of blade included. Your team tested the second model, which I think comes with a premium Freud Diablo blade . . . but what is its model # or exact description? Also, the model you did not test comes with a Skil blade, but again, I cannot find its description anywhere. Can you help by supplying its model #. ??
You’ll also want to be sure to check that the teeth of the blade are facing towards you since this is the direction that the wood is cut. Once you’ve made sure that the new blade is on properly you can put on the stabilizing parts and nut again. You’ll tighten the nut by putting the spanners on the same way you did before, however, this time you’ll push the spanner in your left hand away from you to tighten the nut instead of towards you.
One of the biggest issues and potential hazards when working with table saws is kickback. Table saw kickback occurs when wood is ejected from the saw at extremely high speed. You can imagine the sort of injuries this can cause. Table splitters are effectively small vertical bits of metal or sometimes plastic that are designed to stop the wood flying back if there is a kickback.  Attached to the splitter are anti kickback pawls either side, they look like table saw blades themselves but they are in fact there to grip the wood at stick into it in case of kickback.
One of the first and most important things to consider is what type of table saw you require. When considering the type make sure you consider things like, where will be using the saw, will it need to be portable and move from job to job or can it be stationary like in a work shop. Also, what will be the largest size bits of timber I will be cutting, what sort of power will I require and budget, below we’ve listed the main types so we hope it helps you find the right type for you.
We made a few test cuts with ¾-inch plywood just to get a feel of the motors we were working with. It became clear pretty quickly that not all 15 amp motors are equal. Once we knew what to expect, we moved to pressure treated 2x pine material in 7-1/2 foot lengths. Why 7-1/2? Our test material started at 15 feet and it seemed silly to have some at 8 feet and others at 6.

With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
Since this is a high end cabinet table saw, its features are on par with your expectations. This model comes with your choice of cast iron or stamped steel wings. Kickback is also greatly reduced thanks to the quick release riving knife, while the transparent blade guard comes with independent leaves to complete the set of features you’d expect from a Jet Proshop table saw. If you want, you can also get the Jet Proshop table saw in either a thirty inch or a fifty two inch rip capacity. No matter if you’re a professional or if this is the first cabinet table saw you’re planning to get, the 708494K JPS-10TS won’t disappoint. Its rugged build quality and ease of use qualify it as one of the best table saws you’ve ever used.

Safety is at a pretty high level, to say the least. There are a few integrated mechanisms that prevent accidents from happening, but that doesn’t mean you shouldn’t handle it with care. Also, don’t forget to wear safety equipment at all times. Whether you’re a professional or a beginner, you’ll definitely like this particular model due to its versatility and a wide array of potential.


If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
These tools can be classified into three types, such as the compact, bench top and job site saw. As compared to the stationary models they are smaller and more lightweight. Furthermore, the heavier materials used in their construction are seriously reduced to keep their weight down. Most units are equipped with a 15 amp 120V motor which delivers no more than 2 hp. As it was mentioned before, the size matters and it is an important factor to consider when purchasing a woodworking machine.
This “review” is a giant nothingBurger. There is not one scrap of objective comparison between these saws. Because you sell them, they’re all great and will all zip right through “the hardest woods”. Bulll$hit. You did not test, compare, analyze, or use ANY of these saws. Re-hashinf manufacturer specs is a “Roundup” but it certainly is not a review. Typical sales pablum.
I have a couple questions about your methods and precision. The no-load rpms for the different saws were very different from replicate to replicate for the three different materials. Wouldn’t you expect the no-load speed to be fairly consistent for each saw regardless of which material was going to be used to add load? With that amount of variability in the no-load speed, I wonder how precise any of the measurements were under load?
DIY-ers love this type due to its simplistic yet effective operation. However, it’s not unusual for professionals to invest in these in order to avoid investing in cabinet models and save some money. Speaking of money, you should prepare yourself for a hefty investment if you opt for this particular type. However, most models are well-worth the money. These things last for years and don’t require a lot of maintenance apart from occasional blade replacements and minor adjustments.  They are not as easy to use as portable models, but you’ll learn how to use them in a matter of hours or days, as long as you follow the rules written in the user manual.
Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.

These tools can be classified into three types, such as the compact, bench top and job site saw. As compared to the stationary models they are smaller and more lightweight. Furthermore, the heavier materials used in their construction are seriously reduced to keep their weight down. Most units are equipped with a 15 amp 120V motor which delivers no more than 2 hp. As it was mentioned before, the size matters and it is an important factor to consider when purchasing a woodworking machine.

When it comes to Japanese engineering, Makita are known as a name to be trusted. With that in mind, you can likely imagine what the Makita names in the eastern world, but that doesn’t mean that their products aren’t well suited for use in the United States and other western countries too. The company was formed from a small shop in Nagoya, back in 1915 and since then has expanded across the globe, selling their products in over 150 countries, but still managing to maintain their ethos of good quality.


The Shop Fox W1819 also comes with a miter fence with flip stop which provides excellent workpiece support and is great for longer workpieces. As for the flip stop, it’s going to be very useful especially when wanting to make several cuts of the same width. If you want to cut longer workpieces, you can also flip it out of the way and then pivot it back down in order to make more cuts at the cutting width of your choice.

Among portable table saws, we saw the best feedback for the Bosch 4100-09 (Est. $600). This table saw is among the top performers in four separate professional tests and also earns strong feedback from owners. Professional reviewers consistently say it's powerful, accurate, and easy to set up and use. One feature that gets singled out for praise is the gravity rise stand, which lets users roll the saw around in both its folded and unfolded positions. All reviewers say this stand is very easy to set up and rolls smoothly. Professional testers also like the table saw's sturdy rip fence and its arbor lock, which allows you to change the blade with just one wrench while most saws require two.

It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.
One of the first and most important things to consider is what type of table saw you require. When considering the type make sure you consider things like, where will be using the saw, will it need to be portable and move from job to job or can it be stationary like in a work shop. Also, what will be the largest size bits of timber I will be cutting, what sort of power will I require and budget, below we’ve listed the main types so we hope it helps you find the right type for you.
First, this is not a precise table saw.  This is due to a mix of design flaws and poor manufacturing choices. The placement of the blade guard makes it impossible to see the blade during the cut, which is going to make you less precise and frustrated to boot. The fence is cheap, and may or may not be straight, but even if it is, you have to deal with the fact that flaws in the table itself may result in it not clamping down straight.
Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.
Best of all though, the precision fence and locking miter gauge allow you to dial in the exact angles of bevel and compound miter cuts for complex trim and finishing work. You never have to worry about setting up multiple times for the same cut because the PM2000 is designed to let you “set and forget” while you get your multiple precision cuts made without needing to fiddle with the controls every time. While it is large and extremely heavy, this is definitely the tool of a professional woodworker that will provide performance that meets or exceeds even the most demanding tasks in your woodshop.

I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.
×