Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.
The body of the blade is made from hardened steel, helping to extend the lifespan and keep up with the tooth quality. The kerf is a crazy-thin 0.098 inch—narrow to keep the cuts fast by reducing the amount of material that needs to be removed. Like most Diablo blades, you’ll pay a bit of a premium up front, but the blade lasts so much longer than others on the market that the cost per cut is much lower.
If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
DeWALT DWE7480 is an excellent table saw, especially if you consider its price. It’s a step up from the highly popular DW745 and slightly more expensive, but I think the larger rip capacity and higher RPM are well worth the extra money. The DWE7480 is still in the lower price region though, and unlike the DW745 you can also get this one with a stand: the DWE7480XA!

Among portable table saws, we saw the best feedback for the Bosch 4100-09 (Est. $600). This table saw is among the top performers in four separate professional tests and also earns strong feedback from owners. Professional reviewers consistently say it's powerful, accurate, and easy to set up and use. One feature that gets singled out for praise is the gravity rise stand, which lets users roll the saw around in both its folded and unfolded positions. All reviewers say this stand is very easy to set up and rolls smoothly. Professional testers also like the table saw's sturdy rip fence and its arbor lock, which allows you to change the blade with just one wrench while most saws require two.

We compiled this set of data and created a ranked set of results by assigning a 1-2-3 rating to the relative values of the test measurements. Then we ranked the saws for overall as-manufactured table flatness. As a point of interest, a typical sheet of copy paper is approximately .004 inches thick. Flatness measurements varied from 0.0 to .09 inches.

This is the smallest of all the table saws, typically weighing about 50 pounds or so and designed to sit on top of a table or workbench. Bench style table saws are usually made of steel, plastic and aluminum. They are good for light to medium duty cutting and would not be a good choice if you do a lot of cutting or if you have a professional business. Because it can be lifted by one person and moved around with relative ease, this type of saw is often called a portable table saw. Due to the size of these saws which measure approximately 19” x 27”, they are not designed to rip large pieces of wood. It is also not easy to make mitered cuts. You will notice that there might be more vibration when using this saw as compared to other, larger models. This is due to the lighter weight of the saw. Unfortunately, the vibration can affect the accuracy of the cuts you’re making.
It is a well known fact that table saws are one of the most hazardous tools in a woodworking shops. Seasoned professionals have been known to risk a finger or thumb when using a table saw even while paying close attention to the blade and the material they are cutting. To mitigate the risk to craftsmen, SawStop has created the PCS31230-TGP252 3-HP Professional Cabinet Saw with a unique failsafe to prevent accidents that result in lost time at work, lost wages and lost digits or limbs.
One of the biggest issues and potential hazards when working with table saws is kickback. Table saw kickback occurs when wood is ejected from the saw at extremely high speed. You can imagine the sort of injuries this can cause. Table splitters are effectively small vertical bits of metal or sometimes plastic that are designed to stop the wood flying back if there is a kickback.  Attached to the splitter are anti kickback pawls either side, they look like table saw blades themselves but they are in fact there to grip the wood at stick into it in case of kickback.
From the triple belt drive system, to the three-HP motor and the large cast iron table and wings, the Shop Fox W18193 s built like a tank. You’re also going to love the T-slot miter gauge that features a fence extension and flip stop, but also a four inch port for dust collection and camlock T-fence. There’s also a twenty nine and a half inch rip capacity.
When you need to change the blade, you’ll find that this saw comes with an arbor lock that you can unlock with one hand, which lets you change the blade without any special equipment. It uses a poly-v drive belt system that gives the motor extra power, but this belt system also reduces the noise of the motor, which makes it great those working around others.
A splitter is a piece of metal that keeps the blade from binding in whatever material you are cutting if the saw kerf starts to close up. The splitter is vertical and sits directly behind the blade. This plays a big part in preventing kickback and should be mounted on the motor assembly so it rises and falls with the saw blades movements. You can also get splitters that can be adjusted to fit the width of the kerf.

We found more than 1,000 reviews for this saw at Amazon, Home Depot, and Lowe's, with ratings averaging around 4.6 stars. Owners love the gravity-rise stand and accurate, easy-to-use controls. They also describe the saw as solidly built and easy to set up. Reviewers are mixed on the issue of dust collection; many users complain that the saw produces a lot of dust, but Woodworkers' Journal reports that most of the dust "routed neatly through a shroud that surrounds the blade" and out to a vacuum cleaner.

With a riving knife that has a quick release design that makes it easier to change, it’s no wonder that this Powermatic 1792017K Model PM2000 10-Inch 5 HP 1-Phase Table Saw with 50-Inch Accu-Fence and Workbench is so popular with shoppers. That knife also has built-in kickback prevention that will keep your hands safe and help you focus on your work. Though it’s just as sturdy as other cabinet saws, this one comes with a caster system that allows you to move the saw across your shop.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.

Ryobi’s RTS21G comes in as the only table saw in the group under $200. It’s lightweight, reasonably compact, and we got acceptable jobsite cuts with the upgraded Diablo blade. The throat plate uses magnets to hold it in place while leaving it easy to remove for blade access. Using a threaded rod to push the height adjustment up, you’ll notice it’s easier and smoother on the way down. The stand folds up and can be Velcro-strapped to the back, though it’s a bit wobbly compared to the others when ready for action.
The fence on a table saw is one of its defining features and allows for precise, square, and repeatable cuts. Not all fences are equal though and a poorly built fence is a deal-breaker, in my opinion. Not only will a poorly built and implemented fence affect the quality of your cuts, but a fence that moves or is not square to the blade can cause your material to bind and kickback.
Craftsman 10 table saw Craftsman Radial Arm saw 10Craftsman 16 direct drive scroll saw Chicago Electric 10 compound Slide Miter saw Wagner power painterBlack and Decker rotary saw and jig sawCraftsman corded drill. Craftsman 10 compound miter saw.Cleaning out my shed and am trying to downsize. $550 or best offer and its all yours. Ill help load but wont deliver. Great Christmas gift for that ha...

The price is okay. SawStop is a well-known manufacturer, and they have a pretty good quality control department. In simpler words, it may seem expensive to some, but it’s well-worth the money, especially if you’re a professional. A vast majority of DIY enthusiasts don’t want to make a huge investment in order to tackle a few minor projects; therefore, most of them tend to skip on buying a professional cabinet saw.
Measuring in at 19.9" x 23.4" x 13.4", the SPT70WT-01 is compact enough to fit into any aspiring handyman’s garage, but powerful enough to tackle anything you throw at it on the job site, meaning it’s an ideal entry-level table saw for the amateur hoping to turn his hobby into a career. Sturdiness, durability, and anti-kickback technology make the world’s first worm drive table saw a revolutionary machine. Satisfied buyers can’t get enough of this balanced wood-devouring behemoth.
If you don’t get a model with a flat table, you’re not going to be satisfied with your cut quality. It’s an overgeneralization to say that all good cuts start with a perfectly-flat table on a table saw, but there’s some truth to it. Even minor warping can result in huge changes to the final piece after you’ve made the cut. Unfortunately, it’s not always a problem that can be seen by the naked eye.
It’s best to avoid this issue entirely by making sure that there is no material that could catch on any of your work material and jeopardize your health or safety. Now that you’ve got the basics down for how to properly dress for working with your table saw, you’re ready to inspect your equipment. To start with, you’ll want to make sure the table saw is unplugged before examining it and making sure you’re good to go.
Dust collection can seem like an afterthought for jobsite table saws. The fact that you’re outside, often on an unoccupied site, negates the need to collect your dust. But breathing that stuff doesn’t do your lungs any favors. That’s why dust collection is so important. Of course, if you’re working inside or in an occupied structure, collecting all that dust will make the cleanup part of your day easier to deal with. Since we’re not talking about concrete dust regulations, even a standard shop vac will be a good bet to help contain the mess.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.
The Porter-Cable looks like a beefed-up version of the Craftsman, with the same blade guard and anti-kickback pawls. This is the only saw in our test with a blade-tilting handwheel, which makes it easier to dial in a precise bevel angle. The motor mount and blade controls on this saw are very sturdy, without much play, which translates to a good-quality cut. Extending the fence for a wide rip requires a bit of effort on this saw, since the rails are stiff. All in all, this is a great saw for the price.
The best portable table saw is going to depend largely on what you need the saw for, however, there are three main types of portable table saws; bench top, compact, and job site table saws. These machines vary in their capabilities, but they are all easy to maneuver and move around compared to their stationary counterparts. If you only need a small saw that will be good for your DIY projects, you can likely get by with just a benchtop table saw.
All the articles on this website are short and punchy without much filler, but because there is so much to learn about table saws it will still take you the better part of an afternoon to read through them all. For those who don’t have that kind of time, or those who already know a great deal about table saws, this is the section that will take you to the best table saw for your needs.
×