A gauge will allow you to make very detailed cross and angled cuts. This is a bit of kit that you need to research in great depth as it can make or break the accuracy of your cuts and angles. With a good gauge, you can check blade height, blade angles, miter angles and much more. For further reading checkout Wikipedia’s table saw page and for in-depth air compressor reviews.

Bosch’s 4100-10 work site table saw is a sure win. Bosch never fails to impress us, and this table saw is no exception. It’s a 10 in. saw with a 25 in (right) rip capacity and a 47 degree left bevel. This Bosch table saw is powered by a 15A motor that reaches top speeds up to 3,650 RPM. Another feature we appreciate: its constant response circuits which continuously adapt the speed under load, giving you a continuous blade speed.
Ryobi’s RTS21G comes in as the only table saw in the group under $200. It’s lightweight, reasonably compact, and we got acceptable jobsite cuts with the upgraded Diablo blade. The throat plate uses magnets to hold it in place while leaving it easy to remove for blade access. Using a threaded rod to push the height adjustment up, you’ll notice it’s easier and smoother on the way down. The stand folds up and can be Velcro-strapped to the back, though it’s a bit wobbly compared to the others when ready for action.
Robert Bosch Tool Corporation is aware of questions raised about the power of its REAXX™ Jobsite Table Saw. We are taking this feedback seriously and we’re working with product and engineering teams to answer these questions. Flesh-detecting Bosch Active Response Technology™, which comes on board every REAXX Job Site Table Saw, is unrelated to the questions raised about the saw. The REAXX table saw remains one of the safest and most-advanced table saws available today. 
Just used this saw for the first time today and I love it. Instructions for putting the stand together were not very clear. There's a lot of very detailed reviews here, so there isn't much I can add that hasn't already been said; but one thing I didn't know until using it is that the rear legs are angled further back than the front ones to provide more stability when pushing stock through the saw. Only used it a few times today, but it was a pleasure to use.
The only flaw might be the occasional false detection by the safety system. This will usually only happen if the lumber is wet or it is used primarily in the outdoors. You have to weigh the safety features against the type of work you do. If you are constantly working in wet or damp environments, it might not be worth the headache. If not, it’s 100% worth the benefits!
As you probably might think a quality model must have some safety feature. This is not a toy; this is a powerful tool which can cause serious injury. That’s why, safety features like splitters, anti-kickback or riving knives are there to minimize these risks. When you have your fingers inches away from the blades that spin with a power hard to imagine, you need to be very careful. Therefore, safety features like the ones above will help you keep your hand intact.
One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
Regarding reliability, Dewalt is a fairly dependable brand in the world of portable table saws. This latest offering from Dewalt comes with a big rolling stand that adds to the convenience element. It quickly cuts through over 3 inches depth at 90 degrees and nearly 2.25 inches at 45 degrees. This power is being driven by the powerful 15 amp motor. It cuts small and narrow strips of wood as well as large chunks.
A magnetic switch is also good from a safety standpoint but may not be necessary on these smaller versions. A magnetic switch prevents the saw from starting back up if it loses power during a power outage. Basically, the power outage will turn off the saw. This is good because if for some reason the power were to come back on when you were not near the machine, the material could be shot out of it or damage the saw.

The DEWALT DW745 is a smaller version of the DEWALT DWE7491RS. It’s still a good saw in its own right. It comes with a 15-amp motor, just like the larger unit, though it can only handle rips of up to 20”. You’ll experience the same power and consequently, the same speed as the larger model, though you can’t cut pieces as large. This model is also meant to be moved, and while it doesn’t have wheels, it has a metal roll cage that will help it survive travel without taking any damage.
One drawback is because of the way the blade is stopped, you will want to have an extra blade brake on hand because once it’s used, it cannot be reused. So, if you don’t have another handy, you will have some downtime. Also, the stopping of a blade moving at thousands of RPM can understandably be very hard on the blade itself. Often, the blade may need to be replaced after it has been stopped in this way. Still better than losing a thumb.
DEWALT® table saws are available in both cordless and corded. Our portable table saws are compact for easy transportation between jobsites. They offer a rack and pinion fence system for fast, accurate fence adjustments. Our table saws are lightweight and feature a metal roll cage to ensure they can stand up to a rough jobsite. Tool-free guarding component adjustments make it faster and simpler to adjust as needed. Since the World’s First FLEXVOLT® cordless table saw was introduced, DEWALT has revolutionized the world of cordless construction tools. Every aspect of our table saws are designed to make your job easier.
Is your blade angle taken care of! Good – that means you’re almost done with your safety check process. Now you need to check the material you’re working with. You can’t just pick up any random piece of wood and expect it to fit properly. You’ll have to use wood that is flat and straight. Wood that is curved or that is slightly bowed or cupped will cause issues for you when you try to cut it down – if you need to work with this sort of material you’ll need to find another cutting tool, like the reciprocating saw (click here for full guide).
From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.
Once again our team has put some serious time and effort into our Head-to-Head evaluation to bring you the most comprehensive information available. For this evaluation, we broke things into several categories including: Precision & Accuracy, Performance (power), Price, and Ergonomics. For each of these categories we’ll rank the saws and at the end we’ll name the Best Portable Jobsite Table Saw based on all the results combined.
However, some models with cheaper table surfaces still manage to get it consistently right. It’s always important to look for problems with table flatness when reading reviews of table saws you’re considering. If you see flatness as an issue repeatedly, you can save yourself a huge potential headache by just considering a different model. If you don’t see any complaints about table flatness, even on a cheaper model of table saw, then it’s probably going to work out just fine.
Other than that, this is a great portable saw. It is lightweight and easily moved from location to location. It also has a pro guarding system that basically allows quick and easy adjustments. It also has a metal roll cage to help with durability. Furthermore, it has built in storage which is always welcome. That is a lot of features at this price point!
Though this SawStop ICS53230-52 5 HP 230V 60 Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System is the most expensive model made by the company, we moved it to the bottom of our list because other cabinet saws received better reviews from customers. This saw comes with a 52-inch T-Glide fence system that helps you set the size and angle of each cut, and this system has a lockdown feature to keep the wood from moving.
I’m trying to replace some lost tools for a doctor inflicted, lawyer cowardice sustained injury. I’ve been a woodworker for more years than I might imagine I am comfortable with saying simply for it seems to have been bestowed upon me from birth. The only comment I have is a general comment. As I’ve noticed from about 20 years ago being introduced do officially being educated at a local community college, everyone there had prestige rights attached to it, a couple of cabinet makers I worked for did also that Porter Cable was the Cadilac of woodworking tools. Well, China… Read more »
Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.
It is equipped with plenty of important components and the motor is one of them. It differs from a model to another, but this depends on various circumstances. For example, the smaller models have direct-drive motors that run on 120V circuits. In comparison to all those powerful motors that produce up to 5 hp, the motors designed for smaller units can produce up to 2 hp. This power is enough for cutting thinner material sheets. Keep in mind that the 5hp motors operate on 240V.

Durable Steel Design – With this being such a portable product from Bosch, you’d be forgiven for thinking that it’s pretty flimsy when it comes to design. However, that couldn’t be further from the case with the Bosch GTS1031’s durable and unique all-steel base. This is a design that’s clearly built to take on abuse. That’s definitely peace of mind that you’ll want to have when it comes to using this table saw in a working environment. Not that you shouldn’t be careful where possible when it comes to using your new table saw.
When it comes to power tools, table saws provide convenience when tackling DIY jobs or larger commercial tasks. With their table surface, you are able to get more accurate cuts with the materials you are working with. Utilizing the miter gauge, you will find these power tools to provide the same accuracy as your favorite circular saws without the hassles.

The 50-inc rip fence that comes with this JET 708675PK XACTASAW Deluxe 3-Horsepower is perfect making rip cuts without worrying about your boards slipping out of the place. This fence system has a lock down feature that will actually lock the board down at the right angle and at the measurement that you choose. It comes with an arbor lock changing the blade and a poly-v drive belt system too.


When the blade touches flesh, a brake will stop the blade and the blade drops down below the surface of the table. The operator will presumably leave with only a small nick or no injury at all. These systems definitely bump up the price of the saw, but it’s a major safety feature and just might be able to save you some very expensive medical bills, along with your fingers.

However, some models with cheaper table surfaces still manage to get it consistently right. It’s always important to look for problems with table flatness when reading reviews of table saws you’re considering. If you see flatness as an issue repeatedly, you can save yourself a huge potential headache by just considering a different model. If you don’t see any complaints about table flatness, even on a cheaper model of table saw, then it’s probably going to work out just fine.
Once you’ve tightened the nut again, put on the plate and set both screws back into their original spots. Screw both of the screws back in and then wind your blade back down. Now, clear your work area of any miscellaneous tools and test your machine by plugging it in and hitting the start button. Once you’ve determined that the machine is working properly you can resume your woodwork again.
Bosch’s 4100-10 work site table saw is a sure win. Bosch never fails to impress us, and this table saw is no exception. It’s a 10 in. saw with a 25 in (right) rip capacity and a 47 degree left bevel. This Bosch table saw is powered by a 15A motor that reaches top speeds up to 3,650 RPM. Another feature we appreciate: its constant response circuits which continuously adapt the speed under load, giving you a continuous blade speed.
“The SPT99 table saw can accommodate dado cutting up to 13/16″ wide in a single pass. WARNING -To reduce the risk of injury, always disconnect plug from power source before changing blades. WARNING – To reduce the risk of injury, always use the Skilsaw SPTA70WT-DD 1/2 inch Dado Blade Table Insert or the Skilsaw SPT00A 13/16 inch Dado Blade Table Insert (both include dado accessory washer). Never make dado cuts without this insert. Do not use dado sets larger than 8″ diameter.”
These tests and evaluations are very difficult, take a lot of time, and ultimately limited in scope as we’re not a professional testing company and we’ve got limited time to evaluate the tools. We cannot do longer term testing that would shed light on durability and we can’t possibly test every application that you might use of one of these saws for. However, we feel comfortable that all the table saws in this Head-to-Head are good saws and our testing helps bring to light pros and cons for each saw.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
15 Amp Motor – You’ve likely noticed that the power of motor used by DEWALT in their table saws sits at a pretty consistent 15 amp. That’s no surprise though really, when you take into consideration exactly what a 15 amp motor is able to achieve. In all, we’d say that it provides pretty much as much power you’re going to need. What’s more, this power coupled with high precision allows the table saw to easily rip through just about any hardwood. You’d struggle to find a table saw that pumps out quite as much power.

Once again our team has put some serious time and effort into our Head-to-Head evaluation to bring you the most comprehensive information available. For this evaluation, we broke things into several categories including: Precision & Accuracy, Performance (power), Price, and Ergonomics. For each of these categories we’ll rank the saws and at the end we’ll name the Best Portable Jobsite Table Saw based on all the results combined.

One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.
The DEWALT DW745 is a smaller version of the DEWALT DWE7491RS. It’s still a good saw in its own right. It comes with a 15-amp motor, just like the larger unit, though it can only handle rips of up to 20”. You’ll experience the same power and consequently, the same speed as the larger model, though you can’t cut pieces as large. This model is also meant to be moved, and while it doesn’t have wheels, it has a metal roll cage that will help it survive travel without taking any damage.
I appreciate the helpful comparison of the best table saws. I’m fairly new to woodworking, and until recently I was using an old table saw that used to belong to my dad. Long story short, it’s no longer usable, and so I’m looking for a good table saw to buy that’s beginner-friendly. I have my eye on the DEWALT DW745 – evidently it’s really popular and does a great job. I’ve taken a look at some other sites for more ideas. Your guide here is great. What is your opinion on the DW745?

As with anything, it’s easy to get overwhelmed with the variety of types, sizes, features, colors, weights, what, when, why, where, who…(let me catch my breath). For now, let’s focus on what’s right for you with our Best Portable Table Saw Guide. We’ll start by identifying quality brands that align with your needs. Besides, who wants to buy something that won’t work?

Electric brakes in the saw is an important feature as helps the saw in reversing electricity in the motor, thus contributing to a precise cut. It is highly recommended that when you are buying a saw choose the one with on and off switch. The switch should be easily accessible to make work better and more efficient. In addition, the switch should have a cover. This will keep you from accidentally turning the saw on and damaging your work area or cutting yourself.


The DEWALT DWE7490x 10 Inch Table Saw is an excellent tool for anyone, whether they need it for carpentry work or DIY projects. You’ll be able to complete your tasks with ease thanks to the superb technology and easy transportation. The device comes with powerful 15 amp motor and has impressive maximum depth capabilities. You’ll also be pleased with the 2 inch dust storage port that has a vacuum connection.

The DeWalt, Bosch and Ridgid saws have strong stands that are easier to set up, sturdy fences that lock down parallel to the blade every time, and smooth-operating blade controls. If you’re a contractor or an avid DIYer who just likes top-quality tools that feel good and last a long time, we think the extra few hundred dollars is a good investment.
×