Bosch’s Gravity Rise Stand was the best portable design of the group. While several stands share the basic principles, Bosch stood out with large diameter tubing that improves durability, the ease of set up/take down, and the larger pneumatic wheels that helps over less than ideal terrain. SawStop was right behind with slightly narrower wheels while Ridgid wrapped up the top 3 most impressive.


A table saw has two main ways it can seriously hurt you. One is obvious and that is having any part of your body come into contact with the blade. Any table saw you are seriously considering should have a blade guard installed. The clearer the better. And make sure you leave it on. The blade guard can’t do its intended job from a workbench or shelf.
For this portion of the testing and evaluation we used three different materials (3/4″ AC Plywood, 5/4 Mahogany Decking, and 5/4 Pressure Treated Southern Yellow Pine Decking) while measuring the saw blade RPM, and the saw motor AMP draw. To compare the saws we’re looking for how much blade speed each saw has under load, and also how much the amp draw increases under load. Think about it like driving a car, a more powerful car will not drop as much speed going up a hill and the engine won’t work as hard.
First, this is not a precise table saw.  This is due to a mix of design flaws and poor manufacturing choices. The placement of the blade guard makes it impossible to see the blade during the cut, which is going to make you less precise and frustrated to boot. The fence is cheap, and may or may not be straight, but even if it is, you have to deal with the fact that flaws in the table itself may result in it not clamping down straight.
By the late 18th century, a new tool had been created that would eventually have the sawyers out of work: the circular saw. These early rotating saws were powered by a range of different forces, often including running water or wind, and sometimes driven by animal power. By the early 1800s, the sawmill was replacing the saw pit and its hardworking manual sawyers.
As we said in the beginning of this section, many of these saws will be used, right out of the box, for rough cutting materials and the fine accuracy may not matter so much in that application. If this is the case for a saw, the quality of the cuts and more importantly, the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer. So, TBB wanted to see how the various saws compared right out of the box. The results are in and, as a group, these eight saws measured up quite well for out-of-the-box accuracy.
Safety is at a pretty high level, to say the least. There are a few integrated mechanisms that prevent accidents from happening, but that doesn’t mean you shouldn’t handle it with care. Also, don’t forget to wear safety equipment at all times. Whether you’re a professional or a beginner, you’ll definitely like this particular model due to its versatility and a wide array of potential.

One of my favorite features is the folding fence which essentially increases the surface area of the table to be able to handle larger projects. For instance, I ripped full size 4ft x 8ft sheets of plywood for a home remodel project and the Rockwell Table Saw performed flawlessly. I couldn’t have completed that particular project without the foldable fence extensions.
For this portion of the testing and evaluation we used three different materials (3/4″ AC Plywood, 5/4 Mahogany Decking, and 5/4 Pressure Treated Southern Yellow Pine Decking) while measuring the saw blade RPM, and the saw motor AMP draw. To compare the saws we’re looking for how much blade speed each saw has under load, and also how much the amp draw increases under load. Think about it like driving a car, a more powerful car will not drop as much speed going up a hill and the engine won’t work as hard.

You’ll also want to be sure to check that the teeth of the blade are facing towards you since this is the direction that the wood is cut. Once you’ve made sure that the new blade is on properly you can put on the stabilizing parts and nut again. You’ll tighten the nut by putting the spanners on the same way you did before, however, this time you’ll push the spanner in your left hand away from you to tighten the nut instead of towards you.
Next, you’ll want to focus on protecting your eyes. You’ll need a sturdy pair of safety goggles to make sure you keep your eyes covered at all times. If you don’t take precaution with your eyes they could become injured or irritated by debris that is kicked back from the machine or sawdust that floats in the air. Having itchy, irritated, or otherwise injured eyes is a work hazard that is best to avoid – not having clear eyesight complicates things greatly and puts you at risk for other injuries.

Balancing heavy-duty durability and lightweight design, this machine proves that good things can come in small packages. While buyers are overall happy with their purchases, they do seem to all agree on one thing: the DEWALT DWE7480 may be an overall investment, but it could seriously do with a miter gauge replacement. Buyers report replacing its inaccurate, plastic gauge for a solid, more detailed one.

DEWALT® table saws are available in both cordless and corded. Our portable table saws are compact for easy transportation between jobsites. They offer a rack and pinion fence system for fast, accurate fence adjustments. Our table saws are lightweight and feature a metal roll cage to ensure they can stand up to a rough jobsite. Tool-free guarding component adjustments make it faster and simpler to adjust as needed. Since the World’s First FLEXVOLT® cordless table saw was introduced, DEWALT has revolutionized the world of cordless construction tools. Every aspect of our table saws are designed to make your job easier.
For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.
The table itself is made of heavy cast iron, as are the control wheels for blade depth and angle on the front of the cabinet itself. Unlike many cabinet saws in its class, the G0690 provides up to a 90 degree left tilt bevel, and both blade height and angle can be locked into place for easily repeatable cuts. Better still, the fence is constructed from heavy duty steel, and is cam-locking to keep it stable regardless of vibration or weight of the workpiece.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.

Affordable Price Point – The price of the product is something that you’ll want to carefully consider when it comes to buying a table saw. This is largely because different people have different budgets to work with. Coming in at well under $100, you can likely imagine that this table saw from Ryobi comes in at the lower end of the market and for that low price point, you are going to have to make some compromises in terms of power and speed. However, occasional hobbyists should find that this table saw still gets the job done well.
We really should point out a big deal here and that’s the SawStop. It’s hard to put a price on safety and while the SawStop costs more than 3 times what the Hitachi costs it does offer safety that no other saw in test can offer. For those that can afford the additional cost that feature alone may tip the scales for you. Regardless of price SawStop came in 5th place for the categories we evaluated.

I was hoping to see the JET in there. But glad you didn’t waste your time with it. I bought it a year and a half ago and it’s a piece of crap. It has not held up at all, I keep it in my construction trailer and it has its own cubby hole and is secured with straps. It has fallen apart. The fence has no adjustments and is off 1/4” front to back, From the factory. I have to spend so much time trying to adjust rip fence, and then I can’t turn my guys loose with it because they won’t take the time to adjust and check for accuracy. Just really disappointed in the product. I am waiting for the testing done on the cordless saws because I am upgrading.
A table saw has two main ways it can seriously hurt you. One is obvious and that is having any part of your body come into contact with the blade. Any table saw you are seriously considering should have a blade guard installed. The clearer the better. And make sure you leave it on. The blade guard can’t do its intended job from a workbench or shelf.
By the late 18th century, a new tool had been created that would eventually have the sawyers out of work: the circular saw. These early rotating saws were powered by a range of different forces, often including running water or wind, and sometimes driven by animal power. By the early 1800s, the sawmill was replacing the saw pit and its hardworking manual sawyers.
In the commercial construction business, we typically buy a job site saw for each project and use it up during the course of an 18-month job. When these saws hit the site, they are unboxed, assembled and immediately put into use. We rip stacks and stacks of sheet goods with these saws and the tolerances of the cut materials are not very critical. However, that example represents the portable saw use within our commercial crews’ business.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.
If you need a table saw that can travel, the Bosch 4100-09 consistently earns high marks. Reviewers praise its power, accuracy, easy setup, and easy blade changes. They also love the gravity-rise wheeled stand, which rolls smoothly and snaps open or folds flat in a single lever-activated motion. Finally, they appreciate the convenience of the blade guard system, complete with riving knife and anti-kickback pawls.
Dewalt designed an excellent table saw when they created the DW745 and we consider it to be the best buy on the market from our review. The design is fairly lightweight and easy to transport as it only weighs about 45 pounds. Additionally, the device is full of great features that enable it to work with speed and efficiency that you typically don’t see in a portable saw.
This portable jobsite table saw head-to-head includes 8 saws from; Bosch, Delta, DEWALT, Hitachi, Makita, Ridgid, SawStop and Skilsaw. Originally, we had also to include Ryobi as a budget friendly option for DIY’ers or guys just starting in the trades. However, we were not able to adapt that saw to our testing rigs so we pulled it from the testing (you may see some photos with the saw but again we’re not including it in the results).
Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
Bengt – We appreciate the feedback as it always helps us get better. Having said that I think some of your concerns were evaluated and included in the results in ways that may not be entirely clear. We adjusted each saw after checking the blade/fence measurements and had no issues getting them adjusted (I may add some text to reinforce that in the article). We don’t do long term testing in this type of article as it’s simply not feasible…so making a statement about whether the saw holds those adjustments isn’t feasible. We evaluated the fences and ranked them in the ergonomics section, we even did lateral load testing on them as part of that ranking.
Bosch’s Gravity Rise Stand was the best portable design of the group. While several stands share the basic principles, Bosch stood out with large diameter tubing that improves durability, the ease of set up/take down, and the larger pneumatic wheels that helps over less than ideal terrain. SawStop was right behind with slightly narrower wheels while Ridgid wrapped up the top 3 most impressive.
The blades are categorized according to number of teeth, diameter, arbor size, kerf size, application and speed. They can also be divided by material. Regular commercial table saws are 10-inch or 12-inch. Teeth usually number from 24-80. Many blades are tipped with diamond, carbon or carbide. This lets you cut through more than just wood. You will also need to think about the tilt of the blade. They are available in left tilt or right tilt. With a left-tilting hybrid or cabinet saw, the motor cover can get in the way of the sliding table. Router table extensions don’t work well on left-tilting saws. 
Deciding on what portable saw to get is not an easy task. There is so much out there on the market and such a wide combination of options. You can use our top 5 picks to get a taste of what’s out there and maybe find your perfect portable power saw right off the bat. However, we feel that you should also be equipped with the knowledge to go out and make your own decisions on portable table saws. We are going to run through the most important factors and features to consider before you make your purchase. These are factors that have a direct impact on performance.
We compiled this set of data and created a ranked set of results by assigning a 1-2-3 rating to the relative values of the test measurements. Then we ranked the saws for overall as-manufactured table flatness. As a point of interest, a typical sheet of copy paper is approximately .004 inches thick. Flatness measurements varied from 0.0 to .09 inches.
For the woodworking professional, the 3-horsepower SawStop Professional Cabinet Saw PCS31230-TGP236 is the top pick. Its superior safety features include an excellent riving knife and blade guard system and a unique flesh-sensing blade brake to prevent cuts. Reviewers also praise its performance, exceptional dust control, and overall ease of use. Less expensive versions with 1.75-hp motors are also available (Est. $2,300 and up). The warranty is two years for the saw and five for the motor.
Ridgid’s fence is outstanding for its design. Its large front plate helps stabilize it and the whole thing just feels solid. There’s very little play compared to some of the others and we were consistently able to lock it down perfectly square. We like the pinion style bevel adjustment. It’s not quite a good as a separate adjustment wheel, but a great improvement over simple sliding. We also like the independent locks for both height and bevel. It’s not often that a height lock would be required, but there’s an element of confidence that comes from knowing it won’t be going anywhere.
The cabinet saws are the most powerful woodworking machines. They are durable and strong enough to resist for a long period of time. Most people prefer them because of their impressive features which make them precise and extremely accurate. The motors of these units usually run on 240V and produce from 3 to 5 hp. As mentioned before they are very heavy. Most models weight more than 500 pounds, however, this makes them very stable.
It features an 1850W motor which delivers more than enough power for any heavy-duty task and DIY project. Dewalt is well-known for designing quality tools, and they didn’t disappoint with this particular model either. The fence system offers 610mm of rip capacity. As you may assume, even though it’s a portable unit, you can easily cut large pieces of wood to a particular size.
If you don’t get a model with a flat table, you’re not going to be satisfied with your cut quality. It’s an overgeneralization to say that all good cuts start with a perfectly-flat table on a table saw, but there’s some truth to it. Even minor warping can result in huge changes to the final piece after you’ve made the cut. Unfortunately, it’s not always a problem that can be seen by the naked eye.
Bengt – We appreciate the feedback as it always helps us get better. Having said that I think some of your concerns were evaluated and included in the results in ways that may not be entirely clear. We adjusted each saw after checking the blade/fence measurements and had no issues getting them adjusted (I may add some text to reinforce that in the article). We don’t do long term testing in this type of article as it’s simply not feasible…so making a statement about whether the saw holds those adjustments isn’t feasible. We evaluated the fences and ranked them in the ergonomics section, we even did lateral load testing on them as part of that ranking.

With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.

As you probably might think a quality model must have some safety feature. This is not a toy; this is a powerful tool which can cause serious injury. That’s why, safety features like splitters, anti-kickback or riving knives are there to minimize these risks. When you have your fingers inches away from the blades that spin with a power hard to imagine, you need to be very careful. Therefore, safety features like the ones above will help you keep your hand intact.

The blades of a circular saw are usually divided based on several factors, including diameter, arbor size, speed, application, and well as number f teeth and materials used in their construction. Most tools are equipped with 10 or 12 inches blades. This is the medium size, but there are also models that come with blades as small as 5 inches or as large as one hand. Since they are able to cut various different materials, including the most solid ones, most models have carbide or carbon blades. You may also find diamond-tipped teeth blades, but they are a bit more expensive. The number of teeth is usually between 24 and 80 and you need to decide whether you want a saw with left or right tilt. The direction in which the blade tilt is very important and it can provide plenty of advantages.

We love the  DEWALT DWE749RS 10 Inch Table Saw for it’s great design and easy function . The machine is fairly easy to transport from jobsite to jobsite and we’ve found it to be one of the best portable table saws available to contractors today. The  DEWALT DWE749RS 10 Inch Table Saw helps to keep workspace clean and efficient by incorporating a 2 inch dust collection port into its design. The dust collection port also has a vacuum connection port so you’ll easily be able to suction out all of the dust that comes off the machine blade while you’re hard at work.
When it comes to both appliances and power tools, Bosch is one of the most recognized brands out there. It is equipped with a 15-amp electric motor which has 3650 rpm. Moreover, the diameter of its blade is 10 inches, while the rip capacity is about 25 inches. As compared to other similar units, the Bosch 4100-09 comes with a plethora of safety features, including an arbor lock mechanism which helps you change the blade with ease. In what regards the design of this unit, it’s important to know that it is pretty compact. It measures 39.13 x 30 x 20.9 inches and weighs no more than 60 pounds. Also, keep in mind that the distance between the work surface and the floor is only 37.5 inches. Thanks to the unique properties of the carbide material, the unit is considered to be one of the most durable tools on the market. It is able to cut through pine and plywood which are the softer types of wood out there. Considering its impressive features and powerful motor, the Bosch 4100-09 will certainly be a welcome addition to any workshop.

The DEWALT DWE7490x 10 Inch Table Saw is an excellent tool for anyone, whether they need it for carpentry work or DIY projects. You’ll be able to complete your tasks with ease thanks to the superb technology and easy transportation. The device comes with powerful 15 amp motor and has impressive maximum depth capabilities. You’ll also be pleased with the 2 inch dust storage port that has a vacuum connection.

You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
If you need to move your saw around, it comes with a table saw stand that you can put up and down with ease. Fashioned from aluminum pipes with wheels that can handle uneven terrain, move around site without breaking your back. As well as its user-friendly nature, the stand can be stored away vertically so it’s a real space-saver whether at home or on the jobsite.

In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.
One of my favorite features is the folding fence which essentially increases the surface area of the table to be able to handle larger projects. For instance, I ripped full size 4ft x 8ft sheets of plywood for a home remodel project and the Rockwell Table Saw performed flawlessly. I couldn’t have completed that particular project without the foldable fence extensions.
As you would expect, the most expensive saws made slightly smoother cuts. But the difference was negligible. The only saw that struggled to make smooth cuts in the super-thick oak was the Ryobi. In more common situations, like cutting 3/4-in.-thick material, Ryobi’s cut quality was fine. We found the blades included with all the saws to be adequate for most ripping tasks. But if you want cuts smooth enough for glue joints, you’ll have to invest in a better blade.
×