One of the first things many Pros do is permanently (and intentionally) lose the blade guard and anti-kickback pawls. While they are a pain to install and store onboard, their ability to reduce the risk of injury is significant. Table saws are responsible for thousands of injuries every year and there are plenty of guys running around with stories of how they got injured. So practice installing them until it feels natural and then actually use them onsite.
Once you’ve gathered your materials, turn your attention to the plate in the middle of the table saw. It surrounds the blade and should have two screws that hold it in place (however some models will have four). Use your screwdriver to undo these screws and set them aside. Then take the plate off and set it to the side as well. Then check to make sure the blade is at its full height by going to the back of your table saw and winding the blade up to full height.

We made a few test cuts with ¾-inch plywood just to get a feel of the motors we were working with. It became clear pretty quickly that not all 15 amp motors are equal. Once we knew what to expect, we moved to pressure treated 2x pine material in 7-1/2 foot lengths. Why 7-1/2? Our test material started at 15 feet and it seemed silly to have some at 8 feet and others at 6.

You’ll also want to be sure to check that the teeth of the blade are facing towards you since this is the direction that the wood is cut. Once you’ve made sure that the new blade is on properly you can put on the stabilizing parts and nut again. You’ll tighten the nut by putting the spanners on the same way you did before, however, this time you’ll push the spanner in your left hand away from you to tighten the nut instead of towards you.


TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.
One drawback is because of the way the blade is stopped, you will want to have an extra blade brake on hand because once it’s used, it cannot be reused. So, if you don’t have another handy, you will have some downtime. Also, the stopping of a blade moving at thousands of RPM can understandably be very hard on the blade itself. Often, the blade may need to be replaced after it has been stopped in this way. Still better than losing a thumb.

Delta 36-L336 3 HP Motor Uni-saw with 36 Delta 36-L336 3 HP Motor Uni-saw with 36 in. Biesemeyer Fence System is ideal for woodworking cabinet making and boat building. It features speedometer style scales and a 36 in. Biesemeyer fence. The 3 HP 230-Volt motor cuts hardwoods and engineered products like MDF and melamine. The riving knife enables ...  More + Product Details Close

You’ll also want to make sure that you’re getting a model that doesn’t have a problem with internal dust collection. Some don’t do a great job of funneling the dust towards the port, so it ends up sitting inside the unit. This can affect performance, as sawdust is great at gumming up moving parts. So, if you get one of those models, know that you’re going to have to regularly open it up and clean it out to keep it in tip-top shape, which is a pain, but necessary if you want your unit to last a long time.
For homeowners without the luxury of a huge garage to fit their enormous table saw, DEWALT’s DWE7480 is a compact alternative to bulkier machines with the same wood slicing power. Measuring 25.8" x 26.5" x 13.9", the DWE7480 hosts a 15-amp motor that cuts at an unbelievable 4800 rpm with a ten-inch blade, meaning this small package packs big performance — and with adjustable rear feet that are designed to allow users to level their table saw on uneven surfaces, you’ll be sure to get a clean, precise cut every time, no matter how rugged the terrain. An additional dust port makes collecting your sawdust a breeze — especially if you attach an optional shop vac extension.
From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.
Table saw reviews take the guesswork, and considerable comparative research time-out of the buying equation. Table saw reviews are the result of consolidating the user feedback for the most effective and relevant input. After the data is analyzed, you receive the best of the best, in a condensed version. These streamlined recommendations enable you to spend less time trying to determine which table saw is ideal for your purposes, so that you have more time to use the one you do decide to buy.

That being said, because of their portability, you’ll find that this type of table saw tends to be less powerful than other more permanent saws. This is because they have less power and less noise muffling too, so you’ll find them to be louder. What’s more, because of that aforementioned lack of power, you might find that you’re unable to use the law to cut through certain materials. This shouldn’t put you entirely off a portable table saw though. For many users, they offer the best of both worlds and provide the complete sawing experience that they need from their table saw. Portable Table Saws
For the woodworking professional, the 3-horsepower SawStop Professional Cabinet Saw PCS31230-TGP236 is the top pick. Its superior safety features include an excellent riving knife and blade guard system and a unique flesh-sensing blade brake to prevent cuts. Reviewers also praise its performance, exceptional dust control, and overall ease of use. Less expensive versions with 1.75-hp motors are also available (Est. $2,300 and up). The warranty is two years for the saw and five for the motor.
Scott – I’m assuming you’re talking about the “flatness” of the table and not leveling the saw correct? I will tell you that all jobsite table saws use light weight tables that are NOT machined cast iron like shop saws. Most of the jobsite saws are a light weight cast aluminum top, and NOT machined flat. So there are tolerances in the manufacturing that make it impossible to get a really flat surface. The thing is, in my opinion, for this type of saw it’s not really important. Job site saws are set up for ripping framing lumber, trim, and details that are not as precise as “woodworking” projects. If you need a cut that precise on a job then there are other better approaches including track saws and even pre-cutting materials in the shop. The DEWALT is very similar to the other saws with regard to the table.
Paul – Good catch….I’ve updated that to say Skilsaw not SawStop…thank you! As you can imagine…all the data makes it tough to keep it all straight. I’m not even sure how you’d install that aftermarket fence on these saws. If you do I’d love to see how!! Those really look like they are made to install on cast-iron full size saws. I’d choose the DEWALT with a slight edge over the SKilsaw.
We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
If you’re going to have a quality product, you need a fence system that’s perfectly square to the table so your cut is perfectly parallel to the edge. Obviously, framers have a bit more leeway than jobsite carpenters and there’s plenty of variance in fence quality. Cheaper saws have fences that can easily move out of square as they slide along the surface of the table. Avoid these if you want quality results. The fence system needs to be easy to keep square to the blade.

As we said in the beginning of this section, many of these saws will be used, right out of the box, for rough cutting materials and the fine accuracy may not matter so much in that application. If this is the case for a saw, the quality of the cuts and more importantly, the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer. So, TBB wanted to see how the various saws compared right out of the box. The results are in and, as a group, these eight saws measured up quite well for out-of-the-box accuracy.
The SKILSAW SPT70WT-01 is one of the most efficient circulars saw on the market. It has everything you need. It is quality, durable and has a great price. It comes with a 15 amp dual-field motor that delivers 5300 rpm and 25 inches rip cutting capacity on the table top. The maximum depth of cut at 90 degrees is 3-1/2 inches while at 45 degrees is 2-1/4 inches. The SPT70WT-01 measures 19.9 x 23.4 x 13.4 inches and weighs 49 lbs.. It is a lightweight unit that comes with a compact design. Its lightweight feature makes it portable and easy to transport from a place to another. Thanks to its 10 in. 24 tooth carbide rip cutting blade, this SKILSAW model has the ability to rip any type of wood. As compared to other similar units, this one comes with a plethora of useful accessories, such as rip fence, table insert, barrier guard assembly, miter gauge, push stick, anti-kickback device, blade wrench, hex wrench and manual.
Table saws are pretty complicated pieces of kit and because of that, you can likely imagine that they’re also pretty dangerous at the same time. This is especially the case if you’re using a table saw for the first time. With that in mind, you’ll want to make sure that your table saw features appropriate safety features when buying. There’s nothing worse than falling victim to one of the many accidents that happen every single year as a result of using a table saw.

Lightweight: Typically, you want to choose a portable table saw that is relatively lightweight but sturdy. This will make sure that you are able to work faster and more efficiently compared to heavier options. It also cuts down the strain involved in using this tool as well in moving from one location to another. While looking for lightweight options, do not compromise on the stability element though. If your table saw is not sturdy, it can easily be wobbly while cutting the wood or other material. This is a safety risk but also will end up with junk projects and mistakes. Woodworking is all about precision, and that requires stability.

As accidents and injuries are common when using large power tools like this one, it’s important that you look for safety features such as a dust collection system. Inhaling the sawdust that comes off the wood can make you sick, but this system does a good job of removing the dust from your work area. The collection port itself has a convenient on the cabinet too.

The market for table saws is one that’s incredibly varied and that’s something that you’ve likely already noticed from just one look at the different table saw types. Reading on into our table saw reviews and you’ll notice that there’s also a range of different brands offering table saw products. But which brand is best for you? With so many of them available, it’s hard to understand the difference and make a choice over the best brand for you.


Another good table saw from Powermatic is its 1792006K Model PM2000 5 HP 3-Phase Table Saw with 50-Inch Accu-Fence System and Rout-R-Lift. The dust collection port moves much of the debris you produce away from your work area, but the cabinet itself has a sloped design that makes it easier to get under the cabinet cleaning. Its quick release riving knife not only reduces kickbacks but also reduces the risk of the knife binding.
This next factor to take into consideration when it comes to buying a table saw is more of a safety feature but one that you’ll want to look for in every table saw. It’s basically an automatic switch that turns of the table saw when you walk away. It’s often the case with some cheaper table saws that when you’ve finished using the table saw and forget to flick the power switch, the unit will remain on. This leaves anyone who goes near the table saw open to a considerable amount of danger.
Deciding on what portable saw to get is not an easy task. There is so much out there on the market and such a wide combination of options. You can use our top 5 picks to get a taste of what’s out there and maybe find your perfect portable power saw right off the bat. However, we feel that you should also be equipped with the knowledge to go out and make your own decisions on portable table saws. We are going to run through the most important factors and features to consider before you make your purchase. These are factors that have a direct impact on performance.
If you are just learning how to sharpen your table saw, you may wonder how to know when to sharpen your saw using your best table saw grinder. You do not want to end up sharpening it too much because that will damage your cutters. It is dangerous to work with a saw that is not sharp enough. Dull cutters tend to catch in the materials and propel the bar in the operator’s direction.
Some craftsmen are looking for a cabinet table saw that has both a small footprint but doesn’t sacrifice performance when it comes to cutting and shaping hardwood. If you are that craftsman, then the Grizzly G0690 was built with you in mind. With a 220-volt 3 horsepower motor, this smaller scale cabinet saw is built to rip and split some serious hardwood with minimal effort.
One of the most widely used power tools for carpenters is the table saw. For carpenters that don’t work exclusively in the shop a portable jobsite table saw is essential. For this Head-to-Head we’re focusing on corded portable 10″ jobsite table saws. We are not including cordless table saws in this test as we plan on doing another head-to-head exclusively for cordless table saws later this year as several are available now.
But with top quality saws come features that some people may find well worth the extra investment, substantial though it may be, and thus our discussion starts with pricier models. At the top price range for table saws, you can often get a saw with safety technology that will automatically halt its blade the instant it encounters human flesh. (The process literally takes but a few milliseconds.) The knowledge that your fingers and hands are safe from major injury caused by a rapidly rotating, razor sharp blade is more than convincing enough for many people to invest in these technologically marvelous table saws.
Whether you are a professional contractor who does a lot of work clients, or you just love working with wood, your workshop really needs a cabinet saw. Unlike job site and hybrid saws that are portable, these saws are much heavier and designed use in one location. Cabinet saws come with features like a dust collection port, accident prevention and safety features and fencing systems.
Paul – Good catch….I’ve updated that to say Skilsaw not SawStop…thank you! As you can imagine…all the data makes it tough to keep it all straight. I’m not even sure how you’d install that aftermarket fence on these saws. If you do I’d love to see how!! Those really look like they are made to install on cast-iron full size saws. I’d choose the DEWALT with a slight edge over the SKilsaw.
Now you’re ready to advance on to the next step. Take the spanners out and get ready to put them on the nut. You’ll want to make sure that they are the spanners that originally came with your table saw because they have been tested especially for your machine to make sure they won’t over tighten the nut or screws. Once you’ve made sure that you have the correct spanners, place them on the nut. Use the first spanner with your right hand and use it to stabilize your grip.
I really do like your site and being on Long Island there is a familiarity to the way y’all work. You are quick to respond to comments and put in a great effort but…. This review I feel you miss the mark. Out of box accuracy is important but. Ore important to a pro user is tool able to be adjusted to be near perfect and how does it hold this position. No comments on how solid the fences are, ie deflection movement, ease of micro adjust, etc. all the fancy self feed stuff etc, what saw feels the most powerful? Smoothest ? All theses kizmos are for the manufacturers to hype. Your strengths are that you actually use these machines, so your strengths are to BE MORE opinionated or biased not less because your opinion has meaning or weight. Let the know knowings use the kizmos and just give us your real opinions based on real use. Just my 2 cents.
Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.

In recent years, there has been a cloud of controversy surrounding the inherent safety issues surrounding the table saw. SawStop developed a flesh detection technology that pulls the blade below the table surface 3 milliseconds after coming into contact with skin. It really created a new class of table saw that, as of June 1st, finally has some competition in the form of Bosch’s REAXX.
That said, I have been looking for that ideal replacement saw that will hopefully take me further down the road than the Craftsmen, and a unit that will do what I need it to do. This review could not have been found at a better time. I will take the results that were achieved and use them as a measurement in purchasing a new one. Thanks for the time spent on conducting this testing and review. Very much appreciated!
The final key factor that you’ll want to take into consideration when picking the right table saw is just how easy that table saw is to use. Obviously for experienced table saw users, ease of use might not be something that is so much of a big deal, but if this is going to be your first table saw, it’s definitely something that you’ll want to look out for. The last thing you want is to purchase a brand new table saw and find that you can’t use it.

You have to know the amount of money you are willing to spend for the right saw. The truth is that the price will vary significantly depending on where you are buying the saw, the brand and the features it comes with. However, with a good budget, you can easily narrow down the options you may have. You will have a smaller range to work with and you will know what features to expect within that price range. Always be willing to spend a little more on the table saw you want in your workshop especially if you work on wood every day.
You’ll also find that the metal roll cage base will give you extra strength and durability to work with and the rear feet will enable you to adjust the height of the machine should you be faced with the challenge of working on an uneven surface. There’s nothing the DEWALT DW7480 Compact Job-Site Table Saw can’t handle. You’ll quickly be impressed by its ability to tackle any project you throw at it and learn to appreciate it for the great tool that it is.
You should test the cutting depth of a saw when it is not cutting a bevel. This aspect helps in determining accurate and maximum cutting at 0 degrees. In considering bevel cutting, you should ensure the base plate is adjustable. Look out for adjustment allowance that your saw offers you such as 45, 50 or 90 degrees. The table saw should also be a feature with the flush housing so as to allow the table saw to cut very close to the edge of the wall. It is necessary to look out for this feature as will allow you to cut flooring to size at ease
From the triple belt drive system, to the three-HP motor and the large cast iron table and wings, the Shop Fox W18193 s built like a tank. You’re also going to love the T-slot miter gauge that features a fence extension and flip stop, but also a four inch port for dust collection and camlock T-fence. There’s also a twenty nine and a half inch rip capacity.
The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.
IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:
The same fence system that comes on our number one choice, which lets you change the angle of the wood and make various cuts, also comes on this SawStop ICS31230-52 3HP 230V 60Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System. Designed use in any type of work space, it runs quietly to let you do your work without disrupting others, and it features the same safety system to shut down the saw when it touches any skin. Weighing more than 700 pounds, this is the type of cabinet saw that you can use in the same spot years.

When you need to change the blade, you’ll find that this saw comes with an arbor lock that you can unlock with one hand, which lets you change the blade without any special equipment. It uses a poly-v drive belt system that gives the motor extra power, but this belt system also reduces the noise of the motor, which makes it great those working around others.
Durable Steel Design – With this being such a portable product from Bosch, you’d be forgiven for thinking that it’s pretty flimsy when it comes to design. However, that couldn’t be further from the case with the Bosch GTS1031’s durable and unique all-steel base. This is a design that’s clearly built to take on abuse. That’s definitely peace of mind that you’ll want to have when it comes to using this table saw in a working environment. Not that you shouldn’t be careful where possible when it comes to using your new table saw.
One term you may hear when reading about table saw accuracy is blade runout. Runout is a term that describes whether or how much the outside edge of a saw blade wobbles while being held by the motor shaft. Sometimes, operators measure runout by using a saw blade. In that case, the very use of a saw blade presumes that the specific blade is perfect or nearly perfect in its flatness. Using a saw blade that has any warping will not give a clear indication of blade runout.
The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.
The ultimate safety feature though is the advanced sawstop system that can save users from severe injuries and accidental amputations. Here’s how it works: the blade of the TGP252 is charged with an electrical signal during operation. When human skin comes into contact with the blade, the signal is altered by the body’s natural conductivity. An aluminum brake immediately slams into the blade to bring it to a complete stop, and the stopped blade’s angular momentum drives it down below the surface of the table, preventing any potential secondary contact injuries. This entire sawstop process occurs in an astonishing 5 milliseconds. You simply cannot find a safer professional grade cabinet saw on the market today.
Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
Makita joins DeWalt with an external riving knife release so you don’t have to reach into the throat to loosen it. We actually ran into an issue with the design because of a slightly bent plate holding the knife in place. That aside, the intent of the design is sound and should make for an an easier experience. Because of the external release, Makita screws down the throat plate in place. You should only need to get in there for blade changes if everything functions properly.
A little unusual for Bosch’s larger tools, it comes in reasonably light weight at 60 pounds – only Skilsaw and Ryobi posted lighter weights. Like Milwaukee in our 18V impact driver shootout, the Bosch 4100 didn’t really stand out from the crowd in features and performance. It’s solid consistency in every area we tested earned it the top spot in the class.
While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.
The continuous-read, tape measure–type scale is ingenious and easy to read, and Ridgid’s lifetime warranty covers it against breakage. The Ridgid saw has the most versatile miter gauge with holes and slots for mounting extensions and accessories. The designers have cleverly fashioned the stand to also serve as a left-side outfeed support for ripping plywood.
×