Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.
Though this Jet 708674PK XACTASAW Deluxe 3HP Cabinet Saw comes with the same three-horsepower motor found on the last cabinet saw, it comes with a shorter 30-inch rip fence that may be a little too short some of your projects. It features all the same great features that made Jet so popular with contractors, including a cast-iron enclosed cabinet that stops dust from entering the motor and a poly-v drive belt system that runs more quietly than other belt systems.
Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.
Additionally, the bevel dial is accurate to within ¼ of a degree, making ultra-precise angle cuts easily repeatable. The base of the 36-L552 is also constructed of solid cast-iron, adding balance and stability even when cutting through the toughest hardwood. An aggressive blade guard and splitter design also helps prevent both accidental contact with the blade and pinching or kickback from the kerf even on extended cuts.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
If you’re looking to squeeze the most possible power out of your table in terms of both strength and precision, it’s a cabinet table saw that you’re looking for. They’re what’s seen as a traditional table saw and the variety that most professional wood cutters use on a day to day basis. However, as the name suggests, this raw power and precision comes at the cost of portability. It’s pretty clear that cabinet table saws are designed to sit in one place and be used as a tool within a workshop environment.
Best of all though, the precision fence and locking miter gauge allow you to dial in the exact angles of bevel and compound miter cuts for complex trim and finishing work. You never have to worry about setting up multiple times for the same cut because the PM2000 is designed to let you “set and forget” while you get your multiple precision cuts made without needing to fiddle with the controls every time. While it is large and extremely heavy, this is definitely the tool of a professional woodworker that will provide performance that meets or exceeds even the most demanding tasks in your woodshop.

To provide the ultimate vibration control and stability, the entire cabinet rests on the heaviest cast iron base in the industry, and all steel cabinet components and the cast iron table top are factory fitted to prevent slippage and rattle. Speaking of the table top, the capacious workspace makes shaping and fitting even the longest workpieces quick and easy thanks to its rock-solid support. Dust collection is accomplished via the blade shroud below the table, and can be connected directly to a shop vac thanks to the standard 4-inch diameter power in the rear section of the cabinet.


High RPM: Rotations per minute are an important consideration when you are looking to buy the ideal portable table saw. It ensures that you can cut the wood/material a lot more efficiently and accurately. It also means that the thickness can be adjusted easily, and you can get a plank to the thickness that you would like. The high RPM also makes sure that the cut is relatively smooth and the rips do not show up in the form of uneven edges. On an average, most table saws have a 15 amps motor. It is the RPM that makes a big difference in performance. Anything above 4500 is fantastic.
If you need to move your saw around, it comes with a table saw stand that you can put up and down with ease. Fashioned from aluminum pipes with wheels that can handle uneven terrain, move around site without breaking your back. As well as its user-friendly nature, the stand can be stored away vertically so it’s a real space-saver whether at home or on the jobsite.
Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.
Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.
You often find that many contractors have a love hate relationship with blade guards. Many contractors and woodworkers simply find they often get in the way and can often get wood stuck in them. But many manufacturers are improving these guard’s year on year and now many of them are very advanced and will help keep your fingers from getting hurt, we always advise you to consider the table saw blade feature on any table saw in detail as it could one day help saw you.

The Porter-Cable looks like a beefed-up version of the Craftsman, with the same blade guard and anti-kickback pawls. This is the only saw in our test with a blade-tilting handwheel, which makes it easier to dial in a precise bevel angle. The motor mount and blade controls on this saw are very sturdy, without much play, which translates to a good-quality cut. Extending the fence for a wide rip requires a bit of effort on this saw, since the rails are stiff. All in all, this is a great saw for the price.
Jet also gives you different choices when it comes to the extension wings. Some customers prefer the cast iron wings because they add more weight and keep the table from shifting, but others prefer the stainless steel wings that are durable and easier to use. No matter which wings you choose, you’ll find that you can quickly and easily attach them to the table’s surface to extend the total amount of workspace you have.

As the name indicates, it has a V-belt and a pulley system through which the power is transferred. Given the much higher torque and power, these drives are more suited for heavy-duty sawing jobs, providing better efficiency when cutting thicker wood variants. Additionally, a belt drive throws up much less dust as the motors are mounted far away from the blade. I would say other than that; they are less safe and more costly.


A table saw has two main ways it can seriously hurt you. One is obvious and that is having any part of your body come into contact with the blade. Any table saw you are seriously considering should have a blade guard installed. The clearer the better. And make sure you leave it on. The blade guard can’t do its intended job from a workbench or shelf.
These are only a few of the products that you’ll find we’ve reviewed across the website. If you still haven’t found your perfect table saw, we can guarantee that you’ll find a product that works for you by exploring our table saw reviews. We know that everybody’s needs are different when it comes to table saws, which is why we’ve reviewed a range of products.
While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.
×