A magnetic switch is also good from a safety standpoint but may not be necessary on these smaller versions. A magnetic switch prevents the saw from starting back up if it loses power during a power outage. Basically, the power outage will turn off the saw. This is good because if for some reason the power were to come back on when you were not near the machine, the material could be shot out of it or damage the saw.

The DeWalt, Bosch and Ridgid saws have strong stands that are easier to set up, sturdy fences that lock down parallel to the blade every time, and smooth-operating blade controls. If you’re a contractor or an avid DIYer who just likes top-quality tools that feel good and last a long time, we think the extra few hundred dollars is a good investment.

If you don't need a stand, a benchtop table saw can be an economical and practical choice. The DeWalt DW745 (Est. $300) isn't covered in any professional tests, but it gets excellent reviews from users. This saw is limited somewhat by its small size, as it has only a 20-inch rip capacity and can't make dado cuts. Nonetheless, it earns very high ratings at Amazon with an overall rating of 4.6 stars based on nearly 2,000 reviews. Meanwhile, the more than 600 that weigh in at Home Depot like it even a touch more, granting it a rating of 4.8 stars, with recommendations from 98 percent of users. Owners like its rack-and-pinion fence – the same design found on the larger DeWalt – which they say is accurate and very easy to adjust. Its light, portable size (just 45 pounds) is also a plus. However, like the DeWalt DWE7491RS, it gets a thumbs-down for its flimsy, awkward miter gauge and occasional quality-control problems.
Miter gauges are one of those accessories that you may forget about in daily use, but then desperately need if you don’t have one. They’re used with table saws in order to cut angles that aren’t 90 degrees. The best miter gauges include hard stops at 90 degrees and 45 degrees, which are the angles that you’re most often going to be cutting at. The hard stops make it easy to set the miter gauge to those angles and cut away with confidence.
I have many bundles of old barn boards for sale. These boards are close to 100 years old if not older and they have all had the square and round nails removed from them. This lumber is completely dry and I am selling them in different sized bundles for those who need different amounts of lumber. The old circle saw marks are clearly visible on each board as seen in the pics. Many people use old ...
It’s best to avoid this issue entirely by making sure that there is no material that could catch on any of your work material and jeopardize your health or safety. Now that you’ve got the basics down for how to properly dress for working with your table saw, you’re ready to inspect your equipment. To start with, you’ll want to make sure the table saw is unplugged before examining it and making sure you’re good to go.
Self-Aligning Accuracy – As well as power in your table saw, you’re also going to want it to be as accurate as possible. We can comfortably say that this table saw from Bosch achieves that formidably with its self-aligning accuracy. This basically means that the square lock rip fence aligns itself for accurate performance. If you’re going to be using your table saw regularly and know that you need to get the job done correctly, this will provide it.
More Power: Well, the mathematics of it is fairly simple. When you decide to look for the best table saws, it is always better to go for the one with the maximum horsepower. A saw that is underpowered won’t be of much help in any case. On an average, a motor with 1-2 hp can easily cut through 2-inch thick wood. For greater thickness, you need to opt for table saws with higher horsepower. For example, if you are focusing primarily on wood that is nearly 3 inches thicker, you need a 3-5 hp motor that would run on 240 Volts.
Hitachi C10RJ 10 in. job site table saw features a powerful, industrial grade 15 A motor that operates at 4,500 RPM, giving you the ripping power to cut through even the toughest woods. This Hitachi table saw has a 0-45 degree bevel and height adjustments. One of the best features is its large work table which also has a telescoping extension, allowing rip cuts up to 35 in. wide! When you pair the power of this table saw with the bevel range and table size, you’ll be able to power through any project you throw at it! Other great features include: front mounted controls, oversized controls, integrated safety switch, and a soft start function that helps decrease recoil at startup.
With that in mind, you can likely imagine that hybrid table saws are perfect for those looking for greater power than that offered by a contractor table saw, but don’t fancy paying anything around the price of a cabinet table saw. At the same time, whilst hybrid table saws are nowhere near as portable as some of the aforementioned options, you should still be able to find that they can be transported when necessary. When it comes to the middleman of table saws, that’s a title truly deserved by the hybrid variety. In all, if you’re looking for a bit more power than that offered by a contractor table saw but don’t fancy paying the price of a cabinet variety, this is an option well worth your looking at.
After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
Hitachi C10RJ 10 in. job site table saw features a powerful, industrial grade 15 A motor that operates at 4,500 RPM, giving you the ripping power to cut through even the toughest woods. This Hitachi table saw has a 0-45 degree bevel and height adjustments. One of the best features is its large work table which also has a telescoping extension, allowing rip cuts up to 35 in. wide! When you pair the power of this table saw with the bevel range and table size, you’ll be able to power through any project you throw at it! Other great features include: front mounted controls, oversized controls, integrated safety switch, and a soft start function that helps decrease recoil at startup.
It’s best to avoid this issue entirely by making sure that there is no material that could catch on any of your work material and jeopardize your health or safety. Now that you’ve got the basics down for how to properly dress for working with your table saw, you’re ready to inspect your equipment. To start with, you’ll want to make sure the table saw is unplugged before examining it and making sure you’re good to go.

All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.

Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
And finally, they all include a blade guard that can be removed and reinstalled without tools. Because a few sawing operations, such as non-through cuts, require you to remove the blade guard, we like saws that make this task easy. The Bosch, DeWalt and Ridgid saws have well-designed blade guards that are easy to remove and reinstall. The blade guards on all but the Porter-Cable and Craftsman also have a feature that holds the blade guard in the raised position to allow better blade visibility for setting up cuts.
Whether you’re using your table saw on the go or in the workshop at the back of your house, the last thing you want is for dust to get everywhere when you’re using it. With that in mind, you’re going to want to look for a product that features appropriate dust collection functionality. This might sound like a pretty basic ask out of your table saw, but you’d be amazed to see just how much dust they can generate.
I really enjoyed your review and appreciate the significant time and effort put into it. How did you acquire the machines? Were they evaluation units provided by the manufacturers or did you buy them (randomly, like Consumer Reports)? If they were provided to you the cynic in me says you probably got cherry picked units. In looking at the various machines on line and checking out their comments, it’s quite clear pretty much all of them have a manufacturing distribution of performance and metrics e.g. for accuracy all the units you tested have comments ranging from great to truly awful. Same thing for build quality. I spent quite a while looking at the Dewalt but all the negative reviews on quality and accuracy turned me off it. I certainly do see many more positive reviews than negative reviews for the Dewalt, but it does leave you with the feeling that a dice roll is partly involved in buying a recommended table saw.

Above are the results for RPM Blade Speed while cutting 3/4″ plywood. In the left column is the no-load blade speed and the right column is the lowest recorded blade speed during the cut. The drop in blade speed is fairly small ranging from 6% for Hitachi and Ridgid, 7% for Makita and SawStop, 9% Bosch, 11% DEWALT, 14% SkilSaw, and 24% for the Delta.

Changing a table saw blade may seem daunting, but it’s actually fairly simple and straightforward. You just need to keep a few safety precautions in mind and have the right tools You’ll need to start by making sure your table saw is off. Unplug the device and make sure that when you press the ‘on’ button the blade doesn’t spin. Now that you’re certain the area is safe, it’s time to start. You’ll want to find a screwdriver set and the spanners that came with your table saw before you get going.

All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.
Being concentrated is extremely important. A big percentage of injuries happen due to the lack of focus at any given moment. Remember, if anything happens, it will happen in under a second. Naturally, you won’t have any time to react properly. Music is something that can be dangerous and relaxing at the same time. Some people love working while listening to their favorite tracks, but it significantly lowers your concentration level. Therefore, you should avoid listening to music while operating a heavy-duty piece of equipment.
Contractors who do a lot of finishing work and interior/exterior trim work know the value of a good portable table saw. DeWalt has built the DWE7490X from the ground up as a stable and safe job site cabinet saw that can be used to make those precision cuts quickly and easily without the need to pre-fabricate materials and then bring them to the job site for final fitting.
Great match-up and informative… however I too noticed that “No Load” RPMs varied quite a bit from chart to chart – for the same saw. We would expect some variation of 50 RPM as you had mentioned, but not 500 to 800. See that the Hitachi changed from 4400 down to 3700, Delta jumped from 3700 to 4400, Rigid from 3650 to 4350. Upon closer scrutiny… the order of “No Load” RPMs used in first chart may have been used in all subsequent charts. When the “Load” results were ordered by hi-to-low ranking, is it possible that the “No Load” data was not kept with its saw? If so, that changes the %drop results slightly for most RPM No-Load/Load,Speed charts. No too terrible. Lots of data… Good overall presentation though for use to make informed decisions. Thank you!
A 50 rpm deviation at those speeds is approximately 1% variance which is well within the tolerance we should expect from taking the readings at a precise instant of time. The meters were in constant motion and we took the reading off of a single video frame that represented our determination of no-load speeds. We report them as our instruments showed them. 1% is acceptable.

Table saws can pose a serious risk of injury, since part of the spinning blade comes up above the surface of the table where it can come into contact with the user's hand as it guides the wood. Thanks to voluntary safety standards introduced by Underwriters Laboratories (UL) in 2007, pretty much all table saws now come with blade guards that minimize the risk. Modern guard systems are easier to remove and replace as needed – an important feature because inconvenient blade guards are apt to be left off the saw.
Still featuring the T-Glide Fence System for smooth, safe operation without compromising on precision measurements and secure locking for repeatable cutting, the TGP236 is still an exceptional cabinet saw in its own right Furthermore, the blade height and angle are still fully adjustable via the comfortably large hand wheels on the front and side of the cabinet itself.

We spent over 30 hours researching and testing 10 different brands of table saws and found that maximum speed, cord length, and cut depth were most important. The DEWALT DW7480 table saw scored high marks in every category and is our top pick. This 48 pound table saw is perfect for using at home or taking with you to the job site. It has a powerful 15 amp motor and 24” rip capacity that makes it a favorite with everyone. The 2 ½” dust collection port allowed us to connect the saw to a shop vac and reduce the amount of dust that was in the garage.
Purchasing a quality model is one of the most important investments of a wood-worker. It is a necessary item that is seen in every woodcutter shop. Without this equipment, you won’t be able to complete all your projects based on the hardwood. We all agree that this is a dangerous tool. Also, after doing some research we can truly say that it causes several injuries to the user. However, it also has a lot of advantages besides this drawback. Therefore, in you are interested in finding out more about the advantages of using such a tool, take a look below.
You want to rip down lumber with your table saw. For this you’ll need a fence. You just can’t make an accurate rip cut without one. Check the fence sits on the rails firmly. You should be able to adjust it easily in both directions. A T-square fence is the most common type. Made from welded steel, it’s precise, user-friendly and durable. Some fences are mounted with bolts. Others are welded onto the head of the T-square. Miter gauges are priceless for making cross-cuts and other more advanced cuts. This gauge acts as a guiding device. It moves in the miter slot. You can angle between 45 degrees and -45 degrees. For angled or square cross-cuts or other specialty cuts, a miter gauge fully delivers.
Best of all, this cabinet saw features a cast iron base and trunnions, eliminating vibration while cutting. Combined with the tool-free riving knife, splitter guard and anti-kickback pawls, this is a formidable cabinet saw that doesn’t take up much floor space in the shop. It’s a great value option for the craftsman who is looking to conserve floor space and still have a powerful, high quality cabinet table saw in their shop.
You want to rip down lumber with your table saw. For this you’ll need a fence. You just can’t make an accurate rip cut without one. Check the fence sits on the rails firmly. You should be able to adjust it easily in both directions. A T-square fence is the most common type. Made from welded steel, it’s precise, user-friendly and durable. Some fences are mounted with bolts. Others are welded onto the head of the T-square. Miter gauges are priceless for making cross-cuts and other more advanced cuts. This gauge acts as a guiding device. It moves in the miter slot. You can angle between 45 degrees and -45 degrees. For angled or square cross-cuts or other specialty cuts, a miter gauge fully delivers.
If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  
TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.
First, this is not a precise table saw.  This is due to a mix of design flaws and poor manufacturing choices. The placement of the blade guard makes it impossible to see the blade during the cut, which is going to make you less precise and frustrated to boot. The fence is cheap, and may or may not be straight, but even if it is, you have to deal with the fact that flaws in the table itself may result in it not clamping down straight.

That being said, because of their portability, you’ll find that this type of table saw tends to be less powerful than other more permanent saws. This is because they have less power and less noise muffling too, so you’ll find them to be louder. What’s more, because of that aforementioned lack of power, you might find that you’re unable to use the law to cut through certain materials. This shouldn’t put you entirely off a portable table saw though. For many users, they offer the best of both worlds and provide the complete sawing experience that they need from their table saw. Portable Table Saws
In addition, a top-quality fence should move smoothly and have a scale that’s accurate and easy to read. Our favorite is the DeWalt fence. The rack-and-pinion system keeps the fence parallel to the blade, and the micro-adjusting knob allows easy and precise fence positioning. Runners-up in this category for best table saw are the Ridgid and Bosch saws. They both have superb fences, with the added advantage of T-slots for attaching accessories like featherboards.
×