Should work on any saw that has at least 3/16" of clearance between the LED and the saw carriage. Sorry but the SAW IS NOT INCLUDED. Each LED lamp assembly is precision machined and proudly made in Texas by an old retired veteran who knows what works because he made it for himself first and then decided to share it with others who are looking for the optimal solution at a great price.
The bench top saws have a compact yet ergonomic design. Thanks to their lightweight feature, more and more people prefer to use them in their workshops. Despite the fact that they are not equipped with wheels, they can be considered portable, because they are very small. As such, they can easily be carried and transported from a place to another by almost anyone. Also, in comparison to the jobsite saws, the benchtop saws have a very limited rip capacity.
When you need to change the blade, you’ll find that this saw comes with an arbor lock that you can unlock with one hand, which lets you change the blade without any special equipment. It uses a poly-v drive belt system that gives the motor extra power, but this belt system also reduces the noise of the motor, which makes it great those working around others.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.
Great match-up and informative… however I too noticed that “No Load” RPMs varied quite a bit from chart to chart – for the same saw. We would expect some variation of 50 RPM as you had mentioned, but not 500 to 800. See that the Hitachi changed from 4400 down to 3700, Delta jumped from 3700 to 4400, Rigid from 3650 to 4350. Upon closer scrutiny… the order of “No Load” RPMs used in first chart may have been used in all subsequent charts. When the “Load” results were ordered by hi-to-low ranking, is it possible that the “No Load” data was not kept with its saw? If so, that changes the %drop results slightly for most RPM No-Load/Load,Speed charts. No too terrible. Lots of data… Good overall presentation though for use to make informed decisions. Thank you!
According to the many reviews posted online, the JET 708675PK is an excellent table saw that features a finely ground and large cast iron table that measures twenty nine by forty two inches and provides plenty of work surface for even the most demanding projects. Also, taking a closer look at the front of the blade, you’ll notice it includes ten inches of clear table which is certainly going to be appreciated by a lot of users. Looking under the table, you’ll notice a wide stance, heavy duty cast iron trunnion mechanism which provides the remarkable performance, almost vibration free operation and incredible stability the JET 708675PK is known for.
It is an extremely durable and sturdy product. However, there are some drawbacks. First of all, it is expensive without quite backing up that price in all areas. It does not really have the elite safety feature of our top choice, and it also lacks high-end power. These are minor points (it is still safe and powerful), but you expect it to be perfect at this price.
But with top quality saws come features that some people may find well worth the extra investment, substantial though it may be, and thus our discussion starts with pricier models. At the top price range for table saws, you can often get a saw with safety technology that will automatically halt its blade the instant it encounters human flesh. (The process literally takes but a few milliseconds.) The knowledge that your fingers and hands are safe from major injury caused by a rapidly rotating, razor sharp blade is more than convincing enough for many people to invest in these technologically marvelous table saws.
The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.
Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.

Hitachi C10RJ 10 in. job site table saw features a powerful, industrial grade 15 A motor that operates at 4,500 RPM, giving you the ripping power to cut through even the toughest woods. This Hitachi table saw has a 0-45 degree bevel and height adjustments. One of the best features is its large work table which also has a telescoping extension, allowing rip cuts up to 35 in. wide! When you pair the power of this table saw with the bevel range and table size, you’ll be able to power through any project you throw at it! Other great features include: front mounted controls, oversized controls, integrated safety switch, and a soft start function that helps decrease recoil at startup.
This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.
Buying a table saw can cover a lot of bases. You have everything from DIY models to professional production level cabinet table saws. In this article, we’re looking what is arguably the most popular – jobsite table saws. They’re on the less expensive side and are highly portable compared to their shop counterparts. That makes them go-to tools for framers, jobsite carpenters, and Prosumers.
Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.
Ridgid seems to get mixed reviews from users, maybe due to its lower price point, but continues to impress us in head to head competitions. With this edition, Ridgid’s 15 amp motor powered through cuts better than any other saw we tested. Sure it was close, but it consistently beat out each competitor. That power does come with more vibration than some of the others though.
Often called benchtop, jobsite, or worksite saws, portable table saws are typically made of lightweight materials, such as an aluminum table top, so that they’re easy to move from place to place. Sometimes they’ll have wheels attached to make shifting them around even easier. The motors on portable saws are also much smaller than on other types of table saws, and are typically less powerful.
The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.
Still featuring the T-Glide Fence System for smooth, safe operation without compromising on precision measurements and secure locking for repeatable cutting, the TGP236 is still an exceptional cabinet saw in its own right Furthermore, the blade height and angle are still fully adjustable via the comfortably large hand wheels on the front and side of the cabinet itself.
Flesh Sensor: This is another very important safety measure. While it is possible that this might raise the cost of the saw, nothing is more important than your good health. Flesh sensors stop the blade immediately when they sense a finger on the blade. So instead of a severed finger, you get away with minor cuts. Always choose minor cuts over missing fingers! You do not want to be going to the emergency room with an ice box.

We cannot emphasize enough how important it is to think about safety at all times while using these tools. Even the slightest mistake can make a difference between life and death. The worst part is the fact that it usually happens in an instant, leaving you no time to react at all. Therefore, whatever you do, don’t forget that there’s a thin line between you having ten fingers at one moment and 8 in the next second.
Consequently, they’re going to be a bit heavier than benchtop models. However, their expanding frames mean that you’ll be able to use them even in places where you don’t have access to a table or bench. This is great for construction work, or situations where you’re going to be working outside. This type tends to be a little bit bigger than the benchtop variety, and often has more rip capacity as well.
Additionally, the bevel dial is accurate to within ¼ of a degree, making ultra-precise angle cuts easily repeatable. The base of the 36-L552 is also constructed of solid cast-iron, adding balance and stability even when cutting through the toughest hardwood. An aggressive blade guard and splitter design also helps prevent both accidental contact with the blade and pinching or kickback from the kerf even on extended cuts.
Stands are one of those features where the ends really do justify the means. Some made us wish the manual writers would take a cue from Lego—just make the *@#$! things easy enough for a 7 year old to understand. That aside, SawStop set itself aside brilliantly, taking just 10 minutes to setup. All we had to do was install the wheels and two handles. Even the packaging is designed to make the process easier and the instructions were super-easy to understand. Makita was nearly as simple only requiring us to install the handle and bolt the saw to the stand.
You have to know the amount of money you are willing to spend for the right saw. The truth is that the price will vary significantly depending on where you are buying the saw, the brand and the features it comes with. However, with a good budget, you can easily narrow down the options you may have. You will have a smaller range to work with and you will know what features to expect within that price range. Always be willing to spend a little more on the table saw you want in your workshop especially if you work on wood every day.
If you already own one or more power tool products in Bosch’s range, then you should find that your table saw works comfortably with that. It’s also worth mentioning that Bosch have clearly targeted their power tool products at the general audience, more so than Dewalt who as we’ve already mentioned have designed their products for professionals. Either way, you’ll find that both brands similarly and comfortably offer a good quality cutting experience through their ranges of table saws.
Just in time!!! My Sears Craftsmen portable saw died on me last week. It was only 12 years old with minimal use. It was a nice saw with a nice sized table, not heavy, and a stand that separated and folded like an accordion. Unfortunately, as it turned out, the gear teeth on the worm drive had worn down to the point where the saw started slip and whine. Now that Sears is defunct (Canada), I have no other option than to replace it due to no parts being available.

With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
This portable jobsite table saw head-to-head includes 8 saws from; Bosch, Delta, DEWALT, Hitachi, Makita, Ridgid, SawStop and Skilsaw. Originally, we had also to include Ryobi as a budget friendly option for DIY’ers or guys just starting in the trades. However, we were not able to adapt that saw to our testing rigs so we pulled it from the testing (you may see some photos with the saw but again we’re not including it in the results).
Durable Steel Design – With this being such a portable product from Bosch, you’d be forgiven for thinking that it’s pretty flimsy when it comes to design. However, that couldn’t be further from the case with the Bosch GTS1031’s durable and unique all-steel base. This is a design that’s clearly built to take on abuse. That’s definitely peace of mind that you’ll want to have when it comes to using this table saw in a working environment. Not that you shouldn’t be careful where possible when it comes to using your new table saw.
The thing you might not like about it is the non-flat table top. Many people find this downside as quite a burden, especially if you’re processing perfectly flat wood. Also, the protective coating on the top side of this model is pretty subpar. In fact, it barely protects anything. Consequently, it will peel off quite quickly. As far as the price goes, it’s okay, but it could have been a bit cheaper.
The advent of ever better motive power that came with 19th century developments led to ever more efficient and ever more compact power saws. The first recognizably modern table saws date to the latter decades of that century. With compact and powerful electric motors developed and refined throughout the 20th century, tables saws were widely available and were both compact enough for home use, yet powerful enough for nearly any lumber ripping task.
IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:

Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.
Different types of table saw rely on different motors. With the smaller and more portable saws, 120V direct drive motors can deliver up to 2HP. This is more than enough power if you’re working with less substantial sheets of material. The larger saws have belt drive motors running on 240V. These produce 3-5HP. Think carefully about the materials you’ll be working with. Get the right sized motor for your cutting needs.

To learn about how table saws perform in real people's homes, we consulted owner-written reviews at retail sites like Amazon, Home Depot, Lowe's, and Sears. User reviewers don't have the breadth of experience that many experts enjoy, but they can provide keen insights on the model they bought, including things that might not crop up in the relatively short time professional reviewers have to spend with a given saw.

One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.
Like most other product review sites, ConsumerSearch is supported by a combination of commissions on the sale of the products we recommend and ads that are placed on our site by Google. If you find something you like, you can help support us by clicking through and buying the products we pick. Our editorial process is independent and unbiased; we don’t accept product samples, requests for reviews or product mentions, or direct advertising.

I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.
×