The best overall performance in our testing was the Skilsaw SPT99-12. The Skilsaw was described by many of the TBB crew as a beast and the data reinforces that. Regardless of the type of material the Skilsaw SPT99-12 offered the lowest drop in RPM’s and the lowest increase in AMP draw. Following in second place is the Hitachi C10RJ and the DEWALT DWE7491RS in third place.
Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.
Great job with this testing. As far as the Hitachi. Many sources online point to minimal startups of the Hitachi c10rj before becoming unusable (not starting). The soft start module apparently doesn’t hold up. If it happens in 30 days it can go back to the store but after 30 days you call Hitachi (most described as unpleasant) drive to your closet Hitachi Service center and wait (up to months). I really like the Hitachi myself but am afraid of the soft start module error. THANKS FOR ALL THE GREAT WORK AND CONTENT. Please forgive any punctuation etc. This is tough on phone.

We cannot emphasize enough how important it is to think about safety at all times while using these tools. Even the slightest mistake can make a difference between life and death. The worst part is the fact that it usually happens in an instant, leaving you no time to react at all. Therefore, whatever you do, don’t forget that there’s a thin line between you having ten fingers at one moment and 8 in the next second.


If you’ve purchased a power tool in the past, Dewalt are a name that you’ve likely already heard of and that’s no surprise considering the standard of their products. They’ve been designing and manufacturing some of the world’s best power tools for well over 90 years, so you can likely imagine that you’re going to be in safe hands buying a table saw of any kind from Dewalt. It is worth mentioning though that Dewalt’s products are largely targeted at professional contractors and those within the building industry. However, that doesn’t mean that you can’t find a product in their range that’s suited to your needs.
Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.
Obviously, given its size, the TruePower 01-0819 isn’t the kind of table saw you’d spring for to take on larger projects that require greater motor power — after all, it’s by no means revolutionary in the torque department. But for those who work with smaller materials or softer wood, the Gino Development TruePower 01-0819 Mini Electric Table Saw is a worthwhile, no-frills buy that’s easy on the wallet and can fit in virtually any space with plenty of room to spare.
These saws are extremely lightweight thanks to the materials they tend to be built with (plastic and aluminum) but they are more than capable of getting the job done for small and soft woods like plywood or pine. They typically come at a very affordable price and are perfect for light duty wood cutting work. However, if you need the table saw for contracting, you’re going to want a job site saw. Jobsite table saws are much bigger than either of the other two models, but they are still fairly easy to transport.
And finally, there are a couple of jobsite table saws running around with flesh detection to drop the blade out of the way if it detects a strike. There’s a significant premium in cost for these saws and there has also been plenty of litigation regarding whether it should be required on every table saw and whether more than one company has the right to manufacturer the mechanism. But they’ll save you a much worse injury in the event of an accident.
Delta 36-L352 10 in. contractor table saw is a heavy duty table saw. This big guy is no joke! Its 15 A, 3 HP motor is not only powerful but smooth. This Delta table saw also has a HUGE rip capacity of 50-52 in. and an 82 in. table, so there won’t be much this table saw can’t handle. Its integrated BIESEMEYER fence system, precision bevel gauge, and bevel dial work together to help you get highly accurate cuts down to the nearest 1/4 degree and 1/64 in. Now that’s accurate! Other notable features are its bi-level dust extraction system which helps you keep your workspace clean, large blade opening, and SURE-LOCK dual front cranks for easy access. This table saw is ideal for the pros.
From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.
The design is quite good. The SawStop safety system ensures smooth and flawless operation while protecting you from a variety of hazards. However, regardless of the safety aspects, you should always wear protective equipment, especially gloves and goggles. One of the most notable things about the design is the fact that it provides 99 percent dust collection both below and above the table. The riving knife maximizes kickback and also offers protection.

While your table saw is unplugged, take the time to clear and clean the work surface, removing any debris that could negatively impact the smooth path of the wood you will be cutting. Then, lower or raise the blade to where the blade gullet (the curved section between each blade tooth) is equal with the top of the piece of wood to be cut. Also, make sure that your saw's dust exhaust port is clear and open and that a bag is in place to catch any excess sawdust.

The same fence system that comes on our number one choice, which lets you change the angle of the wood and make various cuts, also comes on this SawStop ICS31230-52 3HP 230V 60Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System. Designed use in any type of work space, it runs quietly to let you do your work without disrupting others, and it features the same safety system to shut down the saw when it touches any skin. Weighing more than 700 pounds, this is the type of cabinet saw that you can use in the same spot years.
On the other end of the handyman spectrum, you’ve got the seasoned professional with years of experience under his belt. We all know the type: he’s the guy that expects only the best, and DEWALT more than delivers with their patented DWE7491RS. This wood-slicing machine is the cream of the crop when it comes to cutting through even the toughest materials. The DWE7491RS measures 26¼" x 22", so it’s a relatively large apparatus — you’re going to want to make sure that you have plenty of space in your garage for this table saw.
So what should you do? The good news is, you don’t need to rely on budget tools to get you through your projects anymore. All you need to do is set aside some time to do some research and investigating so you can find a tool that truly fits your needs. And luckily for you, we’ve taken the time to compile a list of the top 10 best table saws that you can invest in for your woodworking projects.

While we rotated the plate, we recorded the maximum reading on the dial indicator. We validated each maximum reading by running the test for a second time and noting that the readings were consistent. TBB also noted that as we performed these tests on all eight saws, the maximum readings occurred at different parts of the plate along its rotation. Because the max readings were in different and discrete parts of the calibration plate, TBB had a very high level of confidence in the flatness of the calibration plate, itself.

If you’ve read through those reviews and still feel a little overwhelmed, don’t worry. We’ve created a buyer’s guide because we know it can be very hard just by reading reviews. After all, some models are going to work better for some people than for others, and the only way that you’ll know which one is right for you is by understanding your options when it comes to table saws. By reading this general information about table saws, you should gain the knowledge you need to make a well-informed decision about your future table saw.
I agree that these are the most popular TVs as a blend of technology and cost. But to say they are THE BEST TVs for watching footballs is way off. The 85 SONY XBR 900X blows all of these off the map for football, and it is still not the THE BEST. But it's the best under $10,000. Btw - there is no end to the discussion about what is the best. The results will always be spread across the different segments of buyers. I just think this article should say THE MOST POPULAR .. not the BEST.
×