Some table saws go one better than a splitter. Splitters are fixed. They do not move along with the blade. It also needs to be removed if you’re making cross-cuts or dado cuts. A riving knife, on the other hand, is fixed to the same part as the blade. This means it can move along with the blade. Riving knives don’t get in the way either so this is the best option.
The body of the blade is made from hardened steel, helping to extend the lifespan and keep up with the tooth quality. The kerf is a crazy-thin 0.098 inch—narrow to keep the cuts fast by reducing the amount of material that needs to be removed. Like most Diablo blades, you’ll pay a bit of a premium up front, but the blade lasts so much longer than others on the market that the cost per cut is much lower.
The first contractor saws were made to be portable so they could be taken to job sites. These are also lightweight and priced low enough that the handy homeowner can use them. When purchasing the contractor saw there, you will have to make a few concessions. The table is not made of the cast iron top and the extensions are usually made of stamped medal. It is not made as burly as more costly saws. The motor also hangs off the back, which makes it easier to remove when moving the saw to another job site. Bosch table saws are reported to be one of the best budget saws available.

The first thing people notice about this unit is its design. The rolling stand is specially designed to mitigate the transport of this saw. In simpler words, whenever you need to move it, you can do it by simply rolling the unit on its wheels. One more notable thing is the 2-inch dust collector port. You can easily connect it to a vacuum and extract the dust efficiently and without much hassle.


If you are a woodworking professional, you'll want a cabinet saw in your workshop. These are the heaviest, sturdiest and most precise table saws, with powerful motors that require a 220-volt electrical outlet. Cabinet saws require a large, dedicated space because of their guide rails and large tables (often with big extension wings). Then also tend to have the best safety and dust-control features. Woodworkers with enough space (and money) usually make a cabinet saw the permanent centerpiece of their workshop, though a few cabinet saws have mobile bases. Cabinet saws cost $1,600 and up.
Hitachi C10RJ 10 in. job site table saw features a powerful, industrial grade 15 A motor that operates at 4,500 RPM, giving you the ripping power to cut through even the toughest woods. This Hitachi table saw has a 0-45 degree bevel and height adjustments. One of the best features is its large work table which also has a telescoping extension, allowing rip cuts up to 35 in. wide! When you pair the power of this table saw with the bevel range and table size, you’ll be able to power through any project you throw at it! Other great features include: front mounted controls, oversized controls, integrated safety switch, and a soft start function that helps decrease recoil at startup.
Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.
Jeffery – As Rob explained things we had the RPM measurements running on that meter, and had to watch our video playback to evaluate the numbers (no recording of the numbers digitally). So we tried to take the average no load speed watching the video play back. Is it perfect? No….is a 10% difference a big deal? In this application I doubt it. If we were a full blown testing lab we’d have the data recorded digitally and take full blow averages, but alas we are not.
The SawStop SNS175-TGP36 HP Saw is one of the best stationary table saws on the market thanks to its incredible design and impressive build. The saw is able to fit larger dado blades and has an impressive maximum cut depth for you to work with. Additionally, thanks to the left blade tilt, you’ll be able to get work done faster thank you ever thought possible because the tilt helps to prevent boards from being stuck up against the fence. You’ll also be able to get work done quickly and efficiently thanks to the impressive safety system that was built into the saw.
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
The other kind of portable table saw is the wheeled/folding leg variety. The wheeled models come with wheels that can be used to roll them for place to place. The folding leg variety may or may not have wheels. Both models feature a mechanism by which they can be raised up and used without a table. This is what sets them apart from benchtop models.
Bosch’s 4100-10 work site table saw is a sure win. Bosch never fails to impress us, and this table saw is no exception. It’s a 10 in. saw with a 25 in (right) rip capacity and a 47 degree left bevel. This Bosch table saw is powered by a 15A motor that reaches top speeds up to 3,650 RPM. Another feature we appreciate: its constant response circuits which continuously adapt the speed under load, giving you a continuous blade speed.
Accessories 10″ 24-Tooth Carbide Blade, 2x Blade Wrenches, rolling stand, blade guard assembly, push stick, miter gauge, rip fence 10 in. 40-tooth carbide-tipped blade, throat plate insert, smart guard system, rip fence, miter gauge, push stick 32T carbide-tipped blade, rip fence, miter gauge, push stick, and wrenches Rip Fence, Miter Gauge, Smart Guard System, Push Stick, Blade Change Wrenches 24-tooth SKILSAW Carbide-tipped blade for ripping, miter gauge, self-aligning fence, guard system including anti-kick back device, insert plate, push stick and wrench

The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.


When it comes to Japanese engineering, Makita are known as a name to be trusted. With that in mind, you can likely imagine what the Makita names in the eastern world, but that doesn’t mean that their products aren’t well suited for use in the United States and other western countries too. The company was formed from a small shop in Nagoya, back in 1915 and since then has expanded across the globe, selling their products in over 150 countries, but still managing to maintain their ethos of good quality.
Delta 36-L352 10 in. contractor table saw is a heavy duty table saw. This big guy is no joke! Its 15 A, 3 HP motor is not only powerful but smooth. This Delta table saw also has a HUGE rip capacity of 50-52 in. and an 82 in. table, so there won’t be much this table saw can’t handle. Its integrated BIESEMEYER fence system, precision bevel gauge, and bevel dial work together to help you get highly accurate cuts down to the nearest 1/4 degree and 1/64 in. Now that’s accurate! Other notable features are its bi-level dust extraction system which helps you keep your workspace clean, large blade opening, and SURE-LOCK dual front cranks for easy access. This table saw is ideal for the pros.
If you are making a cut that will require your hands to get close to the blade, (within 6 inches) use a push stick or two to eliminate the chances of your hand touching the blade. If this is a big concern for you, maybe consider a saw that uses flesh detection to stop the blade. The additional cost of the saw will be instantly appreciated the first time you need it.
Safety Features: All said and done, you have to accept that the portable table saws are amongst the more dangerous tools to operate. If you are not careful, you can easily get hurt. This makes the safety features some of the most important to consider. I would keep an eye out for features like anti-kickback pawls and blade tilt as they go a long way in avoiding accidents. Most also come with a magnetic switch that makes sure that the machine does not get started on its own accidentally. This is essential. Do not buy a portable table saw without a magnetic switch.
The miter gauge is a part of the unit that moves into the slot. With a miter gauge, you can make a square cross-cut. You just have to set it at 90 degrees and push the board toward the blade. Also, by setting it at 45 degrees, you can make angled cuts. However, when using the miter gauge, make sure the wood is not moving. Secure it to the gauge using a clamp. With a miter gauge, you can also make compound cuts. You just have to set the miter gauge and the level of the blade at the same desired angle.
That said, I have been looking for that ideal replacement saw that will hopefully take me further down the road than the Craftsmen, and a unit that will do what I need it to do. This review could not have been found at a better time. I will take the results that were achieved and use them as a measurement in purchasing a new one. Thanks for the time spent on conducting this testing and review. Very much appreciated!

Ease Of Use: The convenience or ease of use is another key factor to take into account when deciding on the best portable table saw. You have to understand that this device should be something that can be carried easily, fixed simply and used efficiently as and when you need to. Maneuverability is a fundamental element in this matter as well. From setting it up to fixing the wood in place, you have to make sure that the table saw that you buy is convenient and simple to use in all situations and locations. The only caveat to this is if you have one fixed location in mind for 90% of your work or more.
If you are a woodworking professional, you'll want a cabinet saw in your workshop. These are the heaviest, sturdiest and most precise table saws, with powerful motors that require a 220-volt electrical outlet. Cabinet saws require a large, dedicated space because of their guide rails and large tables (often with big extension wings). Then also tend to have the best safety and dust-control features. Woodworkers with enough space (and money) usually make a cabinet saw the permanent centerpiece of their workshop, though a few cabinet saws have mobile bases. Cabinet saws cost $1,600 and up.

To learn about how table saws perform in real people's homes, we consulted owner-written reviews at retail sites like Amazon, Home Depot, Lowe's, and Sears. User reviewers don't have the breadth of experience that many experts enjoy, but they can provide keen insights on the model they bought, including things that might not crop up in the relatively short time professional reviewers have to spend with a given saw.
If you want to take the saw with you and use it in a different location, you can purchase the optional MB-PCS-000 integrated mobile base which features 2 stationary casters and 2 pivoting casters. Furthermore, it’s also possible to upgrade the mobile base assembly to a one thousand pound lift capacity, add a hydraulic piston lift and 4 independent pivoting casters.
The marketplace today is filled with a variety of options at every price range. Once, you have figured out your price range and needs; you should be able to find a choice among our top 5 picks. You can also use our buying guide to inform that choice or to inform your search for a suitable portable table saw in the wider market. There is so much out there, and the quality is getting better every year!
What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.
At this point, you are wondering why this is not number 1. The problem is with all that power, precision, and all those great features; you can get only 18 inches of cut from it. This severely impacts the usability of the product. While it can still be used for some home based products, its use in a professional setup is fairly limited to smaller projects. It also only has a one year warranty which is pretty light.
The table itself is made of heavy cast iron, as are the control wheels for blade depth and angle on the front of the cabinet itself. Unlike many cabinet saws in its class, the G0690 provides up to a 90 degree left tilt bevel, and both blade height and angle can be locked into place for easily repeatable cuts. Better still, the fence is constructed from heavy duty steel, and is cam-locking to keep it stable regardless of vibration or weight of the workpiece.
The Bosch GTS1031 Portable Table Saw is an excellent tool for any craftsman - definitely one of the best tools you could add to your work arsenal. We love that it is easily transported from place to place thanks to its lightweight design and ergonomic carry handle. The design transfers all of the weight of the machine to a specified center of gravity and helps to make it easier to carry the 50 pound machine. The Bosch GTS1031 Portable Table Saw also comes with a smart guard system that helps the device perform at peak levels while keep you safe during your work.

One of the biggest issues and potential hazards when working with table saws is kickback. Table saw kickback occurs when wood is ejected from the saw at extremely high speed. You can imagine the sort of injuries this can cause. Table splitters are effectively small vertical bits of metal or sometimes plastic that are designed to stop the wood flying back if there is a kickback.  Attached to the splitter are anti kickback pawls either side, they look like table saw blades themselves but they are in fact there to grip the wood at stick into it in case of kickback.
We found more than 1,000 reviews for this saw at Amazon, Home Depot, and Lowe's, with ratings averaging around 4.6 stars. Owners love the gravity-rise stand and accurate, easy-to-use controls. They also describe the saw as solidly built and easy to set up. Reviewers are mixed on the issue of dust collection; many users complain that the saw produces a lot of dust, but Woodworkers' Journal reports that most of the dust "routed neatly through a shroud that surrounds the blade" and out to a vacuum cleaner.

The Steel City 35955 also comes with a new table insert system, a seamless table top that offers users a flat surface on which they can work on, but also the Push Stick safety system which prevents injuries to the fingers while using the table saw. Warranty wise, you get 2 years limited warranty, which is enough to give users peace of mind that they’re covered for a long time.

This “review” is a giant nothingBurger. There is not one scrap of objective comparison between these saws. Because you sell them, they’re all great and will all zip right through “the hardest woods”. Bulll$hit. You did not test, compare, analyze, or use ANY of these saws. Re-hashinf manufacturer specs is a “Roundup” but it certainly is not a review. Typical sales pablum.
We spent a lot of time setting up and taking down the saws to see how well the stands worked and how easy it was to install and remove the blade guard and anti-kickback pawls. Then we ran a torturous ripping test with 3-in.-thick slabs of oak to find the best table saw. And finally, we used the saws for more conventional tasks like cutting plywood and ripping framing lumber as another test to determine the best table saw.
×