The throat plate is the removable piece surrounding the blade that sits flush with the table. Removing it gives you the ability to access the blade for removal or riving knife adjustments. The narrower the blade clearance the better for two reasons. First, it helps keep material from falling into the blade area or lodging between the blade and throat plate. Second, it gives you material support very close to the cut to help reduce tearout as the blade exits the cut.
You’ll also want to be sure to check that the teeth of the blade are facing towards you since this is the direction that the wood is cut. Once you’ve made sure that the new blade is on properly you can put on the stabilizing parts and nut again. You’ll tighten the nut by putting the spanners on the same way you did before, however, this time you’ll push the spanner in your left hand away from you to tighten the nut instead of towards you.
In the commercial construction business, we typically buy a job site saw for each project and use it up during the course of an 18-month job. When these saws hit the site, they are unboxed, assembled and immediately put into use. We rip stacks and stacks of sheet goods with these saws and the tolerances of the cut materials are not very critical. However, that example represents the portable saw use within our commercial crews’ business.
Bosch has a long legacy of manufacturing great tools for generations, and the Bosch 4100-09 upholds that tradition. Slightly heavier than the Dewalt DWE, it comes with an innovative stand that makes it stand out. The gravity-rise stand cuts down the time to set this table saw by quite a lot, reducing set up time. It also comes equipped with pneumatic wheels that can roll on almost any surface without much hassle. Another selling point is the advanced T-slot miter gauge that makes sure that you get the right cut every time without fail.

Durable Steel Design – With this being such a portable product from Bosch, you’d be forgiven for thinking that it’s pretty flimsy when it comes to design. However, that couldn’t be further from the case with the Bosch GTS1031’s durable and unique all-steel base. This is a design that’s clearly built to take on abuse. That’s definitely peace of mind that you’ll want to have when it comes to using this table saw in a working environment. Not that you shouldn’t be careful where possible when it comes to using your new table saw.
Powermatic is a name that you’ll see a few times on our list of the cabinet saws because this company is responsible so many great models like this 1792010K PM2000, 5HP 1PH Table Saw, with 50-Inch Accu-Fence System. The built-in caster system makes it easy to move the cabinet saw anywhere around your shop with minimal eft, and it comes with a quick release riving knife that reduces vibrations to prevent accidents. At 39-inches high, it also lets you use the saw without stopping over.
Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. The Makita was given the best score of 1 as it was considerably quieter than the remaining. DEWALT and Delta were ranked worse with a score of 3, while the remaining were ranked as a 2.
If you spend a lot of time working with wood in your garage or workshop, you know the importance of having the best table saw on the market. Many craftsmen find that they feel connected to their work, and because of this they need tools that will work efficiently and reliably. If you’re invested in the art of carpentry, woodcarving, or any other wood related trade, you know that you need a machine that can work efficiently without overwhelming your budget.
Affordable Price Point – The price of the product is something that you’ll want to carefully consider when it comes to buying a table saw. This is largely because different people have different budgets to work with. Coming in at well under $100, you can likely imagine that this table saw from Ryobi comes in at the lower end of the market and for that low price point, you are going to have to make some compromises in terms of power and speed. However, occasional hobbyists should find that this table saw still gets the job done well.
The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.
Table saws can be tougher to evaluate on paper since they don’t include torque measurements. Each of the table saws we tested have 15 amp motors, but vary widely on no load speed. The ones with lower RPM values are bleeding off speed in exchange for torque. While the right balance is always tough to achieve (and is a moving target with every new motor development), here’s where each saw prioritizes speed.

All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.


Lowes had a Father’s day sale, on their Kobalt table saw with a folding/rolling stand and was $180.00, with more money off because I signed up for their credit card-so I bought it. It cuts fine, the fence locks on both ends,measurements seem ok, and it unfolds and rolls away very easily-I like it so far. I’m a home owner and I use it sporadically and treat it well, it does not appear to be very robust, so as a day to day, on the job site saw, probably not a good choice. I used to have a Makita table saw, with a terrible fence, unreliable ruler markings, and difficult to use blade guide that interfered with measurements, which you needed to do every time-a terrible saw, very frustrating to use. I have a Makita miter saw and it’s great, but the idea of buying a same brand because I liked one of their other products did not work out.

Thanks for the work you put in on this. I am retired now and have been researching these types of saws as I wish to begin doing some building of storage shelves and deck furniture. As a beginner, I did not wish to spend huge amounts of money until I was sure it was something I would be staying with for a while :-). Very informative and happy to see the way you did your testing (on the video). I spent 20+ years testing or working with security software testers and totally understand the issues of testing (almost anything) in a fair and honest way. Your work is greatly appreciated!.

Best of all, this cabinet saw features a cast iron base and trunnions, eliminating vibration while cutting. Combined with the tool-free riving knife, splitter guard and anti-kickback pawls, this is a formidable cabinet saw that doesn’t take up much floor space in the shop. It’s a great value option for the craftsman who is looking to conserve floor space and still have a powerful, high quality cabinet table saw in their shop.

I have a couple questions about your methods and precision. The no-load rpms for the different saws were very different from replicate to replicate for the three different materials. Wouldn’t you expect the no-load speed to be fairly consistent for each saw regardless of which material was going to be used to add load? With that amount of variability in the no-load speed, I wonder how precise any of the measurements were under load?


The fence on this system is easily the winner. With clamping on just the front side, it self-aligns better than any other in the group and offers excellent stability. While SawStop didn’t have the most powerful feel to the cuts, it was very smooth with little vibration. Feature preferences aside, the only (slight) negative we agreed on was that the bevel lock stuck a little bit compared to others.
It is an extremely durable and sturdy product. However, there are some drawbacks. First of all, it is expensive without quite backing up that price in all areas. It does not really have the elite safety feature of our top choice, and it also lacks high-end power. These are minor points (it is still safe and powerful), but you expect it to be perfect at this price.
Contractor models also tend to be more powerful and more precise than portable saws, which gives them a definite upside if you’re going to be doing lots of work, or work that requires a fine degree of precision. This type can also be a good choice if you’re going to leave your table saw in one place for extended periods of time, while still being light enough that they can be moved if you need to do so.
If height adjustments were standardized, we could expect each saw to make them nearly identically. Taking a look under the hood, we discovered several different methods—each with their own effect. Most of the saws employ a bevel gear system that provides smooth and reliable performance. We noticed that many used solid metal gearing, but Bosch used plastic for both the 4100 and the REAXX.
You can’t talk about the best portable jobsite table saw without talking about portability. Portability boils down to a couple of important features. First and foremost, weight has a huge impact on how easily you can transport the saw, especially if it has to go into the bed of a truck rather than a trailer. If you’ve got a trailer, then a wheeled stand becomes your best friend. We looked at both.
Consequently, they’re going to be a bit heavier than benchtop models. However, their expanding frames mean that you’ll be able to use them even in places where you don’t have access to a table or bench. This is great for construction work, or situations where you’re going to be working outside. This type tends to be a little bit bigger than the benchtop variety, and often has more rip capacity as well.
The advent of ever better motive power that came with 19th century developments led to ever more efficient and ever more compact power saws. The first recognizably modern table saws date to the latter decades of that century. With compact and powerful electric motors developed and refined throughout the 20th century, tables saws were widely available and were both compact enough for home use, yet powerful enough for nearly any lumber ripping task.
Craftsman 10 table saw Craftsman Radial Arm saw 10Craftsman 16 direct drive scroll saw Chicago Electric 10 compound Slide Miter saw Wagner power painterBlack and Decker rotary saw and jig sawCraftsman corded drill. Craftsman 10 compound miter saw.Cleaning out my shed and am trying to downsize. $550 or best offer and its all yours. Ill help load but wont deliver. Great Christmas gift for that ha...
TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
Ryobi’s RTS21G comes in as the only table saw in the group under $200. It’s lightweight, reasonably compact, and we got acceptable jobsite cuts with the upgraded Diablo blade. The throat plate uses magnets to hold it in place while leaving it easy to remove for blade access. Using a threaded rod to push the height adjustment up, you’ll notice it’s easier and smoother on the way down. The stand folds up and can be Velcro-strapped to the back, though it’s a bit wobbly compared to the others when ready for action.
We compiled this set of data and created a ranked set of results by assigning a 1-2-3 rating to the relative values of the test measurements. Then we ranked the saws for overall as-manufactured table flatness. As a point of interest, a typical sheet of copy paper is approximately .004 inches thick. Flatness measurements varied from 0.0 to .09 inches.
When you purchase your table saw, more than likely it will have standard 10” carbide tipped blade that is good for general purpose use. This blade is capable of cross cutting a 4 x 4. If you replace it with a 40 tooth combination blade you will improve the quality of your cuts significantly and more than likely be much happier with the blade overall. You can get specialty blades also if you are going to be cutting other materials as well.
The obvious starting point for an analysis of which saw is best suited to the needs of a given person (or company, school workshop, and so forth) is the budget at hand. Even the most affordable table saws of a quality meriting serious consideration cost more than 200 dollars; such units are small but still capable of many tasks. The top of the line table saws come with price tags topping out at well over 3,000 dollars and can handle almost any lumber you would ever need cut and then some; more often than not these mighty saws are more tool than needed, so to speak.

On the other end of the handyman spectrum, you’ve got the seasoned professional with years of experience under his belt. We all know the type: he’s the guy that expects only the best, and DEWALT more than delivers with their patented DWE7491RS. This wood-slicing machine is the cream of the crop when it comes to cutting through even the toughest materials. The DWE7491RS measures 26¼" x 22", so it’s a relatively large apparatus — you’re going to want to make sure that you have plenty of space in your garage for this table saw.
It is extremely lightweight so that it can be easily moved around. The best feature for me is the unique capability to capture dust both below and above the blade. That keeps your workplace clean, and you save time. The safety features and ease of use further add to the convenience element. Additionally, the product comes with a 3-year warranty, which is quite good for a tool in this class.
Changing a table saw blade may seem daunting, but it’s actually fairly simple and straightforward. You just need to keep a few safety precautions in mind and have the right tools You’ll need to start by making sure your table saw is off. Unplug the device and make sure that when you press the ‘on’ button the blade doesn’t spin. Now that you’re certain the area is safe, it’s time to start. You’ll want to find a screwdriver set and the spanners that came with your table saw before you get going.
The cabinet saws are the most powerful woodworking machines. They are durable and strong enough to resist for a long period of time. Most people prefer them because of their impressive features which make them precise and extremely accurate. The motors of these units usually run on 240V and produce from 3 to 5 hp. As mentioned before they are very heavy. Most models weight more than 500 pounds, however, this makes them very stable.
While a miter saw is indispensable, having a great table saw is a wonderful way to broaden the scope of your woodworking. Whether you want miters or bevels, rips or compound cuts, the best table saw is a highly versatile woodworking equipment. Not only can you perform a healthy range of different cuts, you can also hook up various accessories to your table saw. Table saws are truly multi-purpose in the workshop.
The biggest advantage of hybrid saws is the fact that they can be plugged in a regular 110V/220V outlet. Therefore, you don’t need any additional power sources in order to use these units. It quite a relief because you’ll avoid any further investments. These saws are quite easy to use if you know what you are doing. However, if you don’t, remember to read the manual before turning your saw on. It will save you a lot of hassle and also keep you safe.
These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.
Patrick – Thanks for the feedback. Trust me, I wish we could spend more time on every aspect but we spent hundreds of hours as it was. I can tell you that the rack and pinion fences are much better than the standard fences of the past. Our entire group felt strongly that we’d prefer the rack and pinion on all the saws. We felt the Ridgid and Delta fences were the least impressive of the standard type.

All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
×