For this portion of the testing and evaluation we used three different materials (3/4″ AC Plywood, 5/4 Mahogany Decking, and 5/4 Pressure Treated Southern Yellow Pine Decking) while measuring the saw blade RPM, and the saw motor AMP draw. To compare the saws we’re looking for how much blade speed each saw has under load, and also how much the amp draw increases under load. Think about it like driving a car, a more powerful car will not drop as much speed going up a hill and the engine won’t work as hard.


Just in time!!! My Sears Craftsmen portable saw died on me last week. It was only 12 years old with minimal use. It was a nice saw with a nice sized table, not heavy, and a stand that separated and folded like an accordion. Unfortunately, as it turned out, the gear teeth on the worm drive had worn down to the point where the saw started slip and whine. Now that Sears is defunct (Canada), I have no other option than to replace it due to no parts being available.
SawStop has an excellent stand and they’ve cleverly hidden the tool/miter/riving knife storage box under the side extension. Move the table extension and the box presents itself. Like DeWalt, two riving knives come with the saw—one with safety guards and one without. This keeps you from wondering how the pawls and guard go on the riving knife. Blade height fully adjusts with only one turn of the wheel. Not everyone was on board with this, citing less accuracy for dado and rabbet cuts. In the end, we showed we could be as accurate on the height as any of the other saws, so it’s a win.
All these saws have attached, collapsible stands with wheels that allow you to roll them around when they’re folded up. A few, like the DeWalt, Rockwell and Ryobi, can’t be wheeled around after they’re set up. But the biggest difference between stands is in how easy it is to set them up. The Ridgid and Bosch have nearly identical stands that work great and require you to only flip or depress one lever to unlock the stand. These are our favorites. The DeWalt stand is the sturdiest of the bunch and very intuitive. It sets up like a card table with legs that fold out and snap into place. The remaining candidates for best table saw have several different stand systems that aren’t quite as easy to set up but that work fine once you get the hang of them.
It’s best to avoid this issue entirely by making sure that there is no material that could catch on any of your work material and jeopardize your health or safety. Now that you’ve got the basics down for how to properly dress for working with your table saw, you’re ready to inspect your equipment. To start with, you’ll want to make sure the table saw is unplugged before examining it and making sure you’re good to go.
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
SawStop has an excellent stand and they’ve cleverly hidden the tool/miter/riving knife storage box under the side extension. Move the table extension and the box presents itself. Like DeWalt, two riving knives come with the saw—one with safety guards and one without. This keeps you from wondering how the pawls and guard go on the riving knife. Blade height fully adjusts with only one turn of the wheel. Not everyone was on board with this, citing less accuracy for dado and rabbet cuts. In the end, we showed we could be as accurate on the height as any of the other saws, so it’s a win.
If you are making a cut that will require your hands to get close to the blade, (within 6 inches) use a push stick or two to eliminate the chances of your hand touching the blade. If this is a big concern for you, maybe consider a saw that uses flesh detection to stop the blade. The additional cost of the saw will be instantly appreciated the first time you need it.
You want to rip down lumber with your table saw. For this you’ll need a fence. You just can’t make an accurate rip cut without one. Check the fence sits on the rails firmly. You should be able to adjust it easily in both directions. A T-square fence is the most common type. Made from welded steel, it’s precise, user-friendly and durable. Some fences are mounted with bolts. Others are welded onto the head of the T-square. Miter gauges are priceless for making cross-cuts and other more advanced cuts. This gauge acts as a guiding device. It moves in the miter slot. You can angle between 45 degrees and -45 degrees. For angled or square cross-cuts or other specialty cuts, a miter gauge fully delivers.
TBB used the same iGauging 35-125-4 digital dial indicator to measure the accuracy of the as-delivered factory fence to the table miter slot. We started by placing the fence in a locked position about 1” away from the blade on the opposite side from the miter slot. We adjusted the throw of the dial indicator so that we took the readings on the indicator, as before, in the middle of the indicator’s range of movement.
The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. There is tool-less assembly of the riving knife and anti-kickback pawls. It has a large easy to access ...  More + Product Details Close
Table saws are pretty complicated pieces of kit and because of that, you can likely imagine that they’re also pretty dangerous at the same time. This is especially the case if you’re using a table saw for the first time. With that in mind, you’ll want to make sure that your table saw features appropriate safety features when buying. There’s nothing worse than falling victim to one of the many accidents that happen every single year as a result of using a table saw.

With a quick release riving knife, this Jet 708676PK XACTASAW Deluxe 5HP with 30 In. Rip Fence reduces the risk of binding and also cuts back on the kickbacks that you might otherwise feel. Its five-horsepower motor is one of the most powerful on the market and can make quick cuts in any type of wood. It also comes with a 30-inch rip fence making rip cuts, though you may find that this fence is a little too short your needs.


Brad – Won’t be anytime soon. I’d offer a few thoughts though on this topic. First off, for this type of testing it’s just not feasible for us to do any long term testing that would be required to evaluate your concern. You’re right, most jobsite table saws have less than perfect fence systems. The rack-and-pinion style that DEWALT, Hitachi and some others use are far more accurate over the long haul than the “clamp” style. Lastly, for lots of guys they are transitioning to track saws for work that requires a really precise cuts or they cut critical pieces in the shop. In a perfect world we’d get shop precision out of jobsite saws, but the reality is due to weight limits its unlikely. Thanks for the feedback.
As you would expect, the most expensive saws made slightly smoother cuts. But the difference was negligible. The only saw that struggled to make smooth cuts in the super-thick oak was the Ryobi. In more common situations, like cutting 3/4-in.-thick material, Ryobi’s cut quality was fine. We found the blades included with all the saws to be adequate for most ripping tasks. But if you want cuts smooth enough for glue joints, you’ll have to invest in a better blade.
The differentiating factor is workshop realestate: it takes up nearly 2 square feet less space than its larger, more powerful counterpart, making it ideal for craftsmen with less workspace who don’t need the extra horsepower for cutting heavier hardwood materials. Best of all, it includes SawStops 5 millisecond safety system to protect craftsmen from accidents that can lead to serious and permanent traumatic injuries.
When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.
Additionally, the W1819 also features a miter fence with flip stop for precisely angled cuts, and the blade can even be tilted left up to 45 degrees for angled cutting when working with bevels, compound miters and chamfers. Furthermore, the fence can be camlocked to keep it steady when making complicated cuts. There are few professional grade table saws that can match the ShopFox 1819 for power, performance features and control. Overall, it makes a fine addition to any working or hobbyist wood shop.
We rotated the blade to the rear of the saw to enable the dial indicator to contact the same location of the same tooth behind the carbide portion. We positioned the dial indicator to the rear of the saw placed onto the blade and the reading recorded. If the blade and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading.
The SKILSAW SPT70WT-01 is one of the most efficient circulars saw on the market. It has everything you need. It is quality, durable and has a great price. It comes with a 15 amp dual-field motor that delivers 5300 rpm and 25 inches rip cutting capacity on the table top. The maximum depth of cut at 90 degrees is 3-1/2 inches while at 45 degrees is 2-1/4 inches. The SPT70WT-01 measures 19.9 x 23.4 x 13.4 inches and weighs 49 lbs.. It is a lightweight unit that comes with a compact design. Its lightweight feature makes it portable and easy to transport from a place to another. Thanks to its 10 in. 24 tooth carbide rip cutting blade, this SKILSAW model has the ability to rip any type of wood. As compared to other similar units, this one comes with a plethora of useful accessories, such as rip fence, table insert, barrier guard assembly, miter gauge, push stick, anti-kickback device, blade wrench, hex wrench and manual.
The purchase of a table saw is no doubt a big investment. But there is a lot of flexibility in this class of tools to find one that fits in with your budget and your wants. Make sure to take into account how you will need to use the tool and where you will need to use it. Heavier models will be sturdier but they will also require more effort to load up when you need to.

One of the first things many Pros do is permanently (and intentionally) lose the blade guard and anti-kickback pawls. While they are a pain to install and store onboard, their ability to reduce the risk of injury is significant. Table saws are responsible for thousands of injuries every year and there are plenty of guys running around with stories of how they got injured. So practice installing them until it feels natural and then actually use them onsite.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.

Delta has also improved the tabletop geometry on this model which means that you’re going to get more surface area stabilization. The base is also made of durable cast iron and since it offers easy access to the off/on switch, using the Delta UNISAW is a breeze. Other user friendly features include the convenient dust extraction system, large blade opening for easily changing the blade and fine-tuning the riving knife, smart storage for simple organization and fast access.
TBB used the same iGauging 35-125-4 digital dial indicator to measure the accuracy of the as-delivered factory fence to the table miter slot. We started by placing the fence in a locked position about 1” away from the blade on the opposite side from the miter slot. We adjusted the throw of the dial indicator so that we took the readings on the indicator, as before, in the middle of the indicator’s range of movement.
Some of the key table saw brands included Dewalt, Bosch, Makita and Ryobi. You’ll notice that we’ve featured a number of these brands across our table saw reviews. You’ll also find that these different brands offer something very different in terms of their features and functionality. With that in mind, we’ve put together a comprehensive summary of those brands on this very page and you’ll find more detailed information about them across the website and also information about choosing the best brand of table saw for you.
We found more than 1,000 reviews for this saw at Amazon, Home Depot, and Lowe's, with ratings averaging around 4.6 stars. Owners love the gravity-rise stand and accurate, easy-to-use controls. They also describe the saw as solidly built and easy to set up. Reviewers are mixed on the issue of dust collection; many users complain that the saw produces a lot of dust, but Woodworkers' Journal reports that most of the dust "routed neatly through a shroud that surrounds the blade" and out to a vacuum cleaner.
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
Contractor saws weigh quite a bit more than portable saws, averaging between 150 and 350 pounds, but are still somewhat portable. They have a heavier, cast-iron table top, and a motor that is usually more powerful than a jobsite saw. Even so, they’re within prices affordable for more committed hobbyists. Contractor saws can range between $800 and $2,000. They’re good for basic cutting tasks, as well as making home furniture and cabinetry work.
You’ll also want to make sure that you’re getting a model that doesn’t have a problem with internal dust collection. Some don’t do a great job of funneling the dust towards the port, so it ends up sitting inside the unit. This can affect performance, as sawdust is great at gumming up moving parts. So, if you get one of those models, know that you’re going to have to regularly open it up and clean it out to keep it in tip-top shape, which is a pain, but necessary if you want your unit to last a long time.
Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.
One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
Jet also gives you different choices when it comes to the extension wings. Some customers prefer the cast iron wings because they add more weight and keep the table from shifting, but others prefer the stainless steel wings that are durable and easier to use. No matter which wings you choose, you’ll find that you can quickly and easily attach them to the table’s surface to extend the total amount of workspace you have.
Jeffery – As Rob explained things we had the RPM measurements running on that meter, and had to watch our video playback to evaluate the numbers (no recording of the numbers digitally). So we tried to take the average no load speed watching the video play back. Is it perfect? No….is a 10% difference a big deal? In this application I doubt it. If we were a full blown testing lab we’d have the data recorded digitally and take full blow averages, but alas we are not.
There are two major points that affect post-calibration table saws: fence quality and overall stability. A fence works by grabbing hold of the table edge and clamping into it. The best fences, like Biesemeyer, have three points of contact. They’re just not where you’d expect. All three are on the front, leaving none on the back. With a wide cast metal front clamping system, the front is pulled flush and self-aligns. It requires a solid locking mechanism to ensure the fence doesn’t move during cuts, but it is very possible.
My son Owen and I thank you for the truly wonderful, informative and entertaining experience provided by the TOH staff, crew and trades-people at the Pro2Pro Brookline event. From Elizabeth - who welcomed us to the event, to Chris, Kevin and others who were wonderful during the orientation session (answering questions that I'm sure you have heard dozens of times before), to Charlie, Kevin, Richard, Heath (the electrician) and Thomas (the program director), you helped us Insiders to understand and appreciate the pride that you take in your work. It was refreshing. I loved the pictures and accompanying text of the event that you posted. I have to say in closing to Chris, Kevin and Thomas (in particular) you gave my son, a budding landscaper, the impetus to continue his pursuit of the trades. Kudos to you all and keep up your great work!
×