One of the things we looked at was the ease of assembly out of the box. We had the same person assemble each of the saws and timed the assembly to see if there are any significant differences between the models. The assembly time for the saws ranged from 21 minutes to 48 minutes. While some stands required more than twice the time, we felt the assembly time was not a significant enough factor to change someone’s mind on which saw to purchase.
With a single cast iron trunnion system, the Delta UNISAW offers dependable accuracy, smooth and continuous operation, but also vibration free control. Thanks to the fact that it features a fifty-two inch fence system, it’s the perfect choice for woodworking pros, but also people who are just starting out in the woodworking industry, such as hobbyists. Since it also comes with an upfront bevel dial to easily fine tune the blade level, you get a striking accuracy within a quarter of a degree, ensuring precision setups cut after cut.
Flesh Sensor: This is another very important safety measure. While it is possible that this might raise the cost of the saw, nothing is more important than your good health. Flesh sensors stop the blade immediately when they sense a finger on the blade. So instead of a severed finger, you get away with minor cuts. Always choose minor cuts over missing fingers! You do not want to be going to the emergency room with an ice box.
Lowes had a Father’s day sale, on their Kobalt table saw with a folding/rolling stand and was $180.00, with more money off because I signed up for their credit card-so I bought it. It cuts fine, the fence locks on both ends,measurements seem ok, and it unfolds and rolls away very easily-I like it so far. I’m a home owner and I use it sporadically and treat it well, it does not appear to be very robust, so as a day to day, on the job site saw, probably not a good choice. I used to have a Makita table saw, with a terrible fence, unreliable ruler markings, and difficult to use blade guide that interfered with measurements, which you needed to do every time-a terrible saw, very frustrating to use. I have a Makita miter saw and it’s great, but the idea of buying a same brand because I liked one of their other products did not work out.
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.

Smoothness & Accuracy: This is another important factor to be aware of. You need to make sure that you decide on a portable table saw with a blade that can cut any type of wood easily. The fence needs to be able to fix the wood securely, and a miter gauge adds to the overall accuracy element. It also significantly adds to the range of options you can use the table saw for.
If you need a table saw that can travel, the Bosch 4100-09 consistently earns high marks. Reviewers praise its power, accuracy, easy setup, and easy blade changes. They also love the gravity-rise wheeled stand, which rolls smoothly and snaps open or folds flat in a single lever-activated motion. Finally, they appreciate the convenience of the blade guard system, complete with riving knife and anti-kickback pawls.
Both the riving knife and the blade itself has a quick release design that lets you remove each one in minutes after accessing the arbor lock and without using any special tools either. The blade guard has a similar design that allows you to remove and replace it without any tools. This guard does a good job of keeping your hands and any other body parts safe as you use the saw.
We went through a large number of portable table saw reviews to help you identify the top options that you could choose from. If you do not have the time to surf through hundreds of options available online, this list will make the task easier for you. Of course, you can also use our buying guide to sift through options outside this list. In saying that, let’s get started with our top pick, the DEWALT DWE7491RS!

The thing you might not like about it is the non-flat table top. Many people find this downside as quite a burden, especially if you’re processing perfectly flat wood. Also, the protective coating on the top side of this model is pretty subpar. In fact, it barely protects anything. Consequently, it will peel off quite quickly. As far as the price goes, it’s okay, but it could have been a bit cheaper.
Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.

Additionally, you’ll be able to enjoy the dust collection port system on the cabinet. It leads its industry in its ability to efficiently gather up to 99% off all dust put off by the device both above and below the table. The SawStop PCS31230-TGP252 Professional Cabinet Table Saw is a powerful and invaluable device - definitely one of the best investment choices you could make.

Above are the results for RPM Blade Speed while cutting 3/4″ plywood. In the left column is the no-load blade speed and the right column is the lowest recorded blade speed during the cut. The drop in blade speed is fairly small ranging from 6% for Hitachi and Ridgid, 7% for Makita and SawStop, 9% Bosch, 11% DEWALT, 14% SkilSaw, and 24% for the Delta.
Table saws in this best table saw review run the gamut in price and quality. You can buy a table saw for as little as $150, and if you use it just to occasionally rip a board, that may be all the saw you need. If you want a saw that’s easy to carry and you don’t need to rip sheets of plywood in half, look for a “compact” saw like the DeWalt DW745 (shown) or the Bosch GTS1031. If you have room for a little larger saw that’s slightly less portable but capable of wide rips, consider one of the best table saws we review here. And finally, if you want to build cabinets or furniture and have a big enough work area, you can step up to a stationary contractor’s saw like the Ridgid R4512 (shown), for about $650.
3,650 Rotations Per Minute – As you’ll find above in this page, portable table saws tend to be a little less powerful than well, their less portable counterparts. However, the 3,650 rotations per minute offered by this 10-inch table saw allow for both high precision and incredibly powerful cutting. Plus, with a rotations per minute of 3,650, you’ll find the product to be considerably faster at cutting just about anything. If you care about how portable your table saw is, but don’t fancy compromising on speed and power, you wouldn’t be mistaken for thinking that the Bosch 4100-09 truly has it all.

The final key factor that you’ll want to take into consideration when picking the right table saw is just how easy that table saw is to use. Obviously for experienced table saw users, ease of use might not be something that is so much of a big deal, but if this is going to be your first table saw, it’s definitely something that you’ll want to look out for. The last thing you want is to purchase a brand new table saw and find that you can’t use it.
Changing a table saw blade may seem daunting, but it’s actually fairly simple and straightforward. You just need to keep a few safety precautions in mind and have the right tools You’ll need to start by making sure your table saw is off. Unplug the device and make sure that when you press the ‘on’ button the blade doesn’t spin. Now that you’re certain the area is safe, it’s time to start. You’ll want to find a screwdriver set and the spanners that came with your table saw before you get going.
The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.
Still featuring the T-Glide Fence System for smooth, safe operation without compromising on precision measurements and secure locking for repeatable cutting, the TGP236 is still an exceptional cabinet saw in its own right Furthermore, the blade height and angle are still fully adjustable via the comfortably large hand wheels on the front and side of the cabinet itself.
Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.

I just purchased this saw last week. It took several hours to assemble. everything was there and I had no problems putting it together. Not hard but time consuming. The first job was to rework some vertical drawers. It did a good job fence worked great as did the riving knife. Saw was quitter than I expected. overall I am very happy. The only problem was that I had to weight a couple of extra days for delivery due to all parts not arriving at the same time.
All the articles on this website are short and punchy without much filler, but because there is so much to learn about table saws it will still take you the better part of an afternoon to read through them all. For those who don’t have that kind of time, or those who already know a great deal about table saws, this is the section that will take you to the best table saw for your needs.
×