I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!

Contractors who do a lot of finishing work and interior/exterior trim work know the value of a good portable table saw. DeWalt has built the DWE7490X from the ground up as a stable and safe job site cabinet saw that can be used to make those precision cuts quickly and easily without the need to pre-fabricate materials and then bring them to the job site for final fitting.


One of the lightest and most compact table saws was also the most stable: Skilsaw. There’s no wheel base to the stand and the outward angled legs provide a wider platform than it may appear against its colleagues. In second place was DeWalt, also offering a wide platform, but without the amount of rigidity that Skilsaw has in their stand. Coming up in third was Bosch with its gravity rise stand followed closely by Ridgid. It’s important to note that none of the professional class table saws had any stability issues inherent to their extension locking—it was all in the stand.
The 50-inc rip fence that comes with this JET 708675PK XACTASAW Deluxe 3-Horsepower is perfect making rip cuts without worrying about your boards slipping out of the place. This fence system has a lock down feature that will actually lock the board down at the right angle and at the measurement that you choose. It comes with an arbor lock changing the blade and a poly-v drive belt system too.
This type requires a heavy-duty circuit because it’s driven by a powerful 3 to 5HP motor. The blade is driven by three parallel V-belts which ensure a smooth operation and an efficient transfer of energy. Needless to say, if you have big plans, you might want to consider investing in a high-quality cabinet saw. Prompted, it’s going to cost you a significant amount of money, but it pays out relatively quickly.

In layman’s terms, a miter gauge is a device that allows users to set up the angle of the material being cut with a table saw. And while most table saws come with built-in miter gauges, others, well, don’t — which is why the Kreg KMS7102 Table Saw Precision Miter Gauge System is invaluable. Whether you’re replacing an old, worn-out gauge or putting it to use in conjunction with a table saw that didn’t come with its own proprietary gauge, the KMS7102 is specially designed with precision in mind. After all, accuracy is vital to successful woodwork.

You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
The DEWALT DWE7490x 10 Inch Table Saw is an excellent tool for anyone, whether they need it for carpentry work or DIY projects. You’ll be able to complete your tasks with ease thanks to the superb technology and easy transportation. The device comes with powerful 15 amp motor and has impressive maximum depth capabilities. You’ll also be pleased with the 2 inch dust storage port that has a vacuum connection.

First, this is not a precise table saw.  This is due to a mix of design flaws and poor manufacturing choices. The placement of the blade guard makes it impossible to see the blade during the cut, which is going to make you less precise and frustrated to boot. The fence is cheap, and may or may not be straight, but even if it is, you have to deal with the fact that flaws in the table itself may result in it not clamping down straight.
The last one in our list of the top portable table saw picks is another offering from Bosch. If you are looking for a sleek and extremely portable table saw, then this is for you. It weighs merely 52 pounds and can be easily carried around anywhere that you might go. The ergonomic grip and the uniform weight distribution further enhance the portability aspect.

If you’ve purchased a power tool in the past, Dewalt are a name that you’ve likely already heard of and that’s no surprise considering the standard of their products. They’ve been designing and manufacturing some of the world’s best power tools for well over 90 years, so you can likely imagine that you’re going to be in safe hands buying a table saw of any kind from Dewalt. It is worth mentioning though that Dewalt’s products are largely targeted at professional contractors and those within the building industry. However, that doesn’t mean that you can’t find a product in their range that’s suited to your needs.


The DEWALT DWE7491RS is an incredible saw, but it provides portability at a great price point. The set of wheels on this model is great for moving it from jobsite-to-jobsite without too much effort. The folding legs are also superior to the support systems on other models, and they make it so that you always have a stable platform on which to work, without adding too much weight to the machine.
DEWALT® table saws are available in both cordless and corded. Our portable table saws are compact for easy transportation between jobsites. They offer a rack and pinion fence system for fast, accurate fence adjustments. Our table saws are lightweight and feature a metal roll cage to ensure they can stand up to a rough jobsite. Tool-free guarding component adjustments make it faster and simpler to adjust as needed. Since the World’s First FLEXVOLT® cordless table saw was introduced, DEWALT has revolutionized the world of cordless construction tools. Every aspect of our table saws are designed to make your job easier.
How many teeth a saw blade has will determine how smooth the cut is. Most blades have from 24-80 teeth. The exceptions to these blades are specialty material specific blades (i.e. for masonry) In general, the more teeth a blade has the smoother the cut will be. The higher tooth count means that the cut speed will be slower as well. You cannot overcome a slower cutting speed by pushing harder on the material. This is a common mistake newbies make. All this will do is cause kickbacks when the saw blade catches and tosses the object back towards to the user at dangerously high speeds.

The Bosch 4100-09 offers many advanced features, making it a very capable table saw for woodworking. The air-filled wheels and gravity rising stand makes this table saw functional and lightweight. Set up and tear down of the table saw is a breeze. This technology allows the table saw to be moved from place to place, even over the most rough and challenging areas of the work site. The 4100-09 weighs 39 pounds, making it the perfect portable table saw. Although it is lightweight, it is very durable and stable.


Different types of table saw rely on different motors. With the smaller and more portable saws, 120V direct drive motors can deliver up to 2HP. This is more than enough power if you’re working with less substantial sheets of material. The larger saws have belt drive motors running on 240V. These produce 3-5HP. Think carefully about the materials you’ll be working with. Get the right sized motor for your cutting needs.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.
Obviously, given its size, the TruePower 01-0819 isn’t the kind of table saw you’d spring for to take on larger projects that require greater motor power — after all, it’s by no means revolutionary in the torque department. But for those who work with smaller materials or softer wood, the Gino Development TruePower 01-0819 Mini Electric Table Saw is a worthwhile, no-frills buy that’s easy on the wallet and can fit in virtually any space with plenty of room to spare.
If you’re looking for the perfect cabinet table saw out there, then you should look no further than the SawStop ICS51230-52. This is an industrial grade cabinet saw and is also the highest quality, most powerful and heaviest cabinet saw you can currently get. Its fifty two inch industrial T-glide fence assembly, combined with a 5 HP, 230V single phase motor offers safety, versatility, durability and peace of mind that SawStop is so well known for.
You’ll be able to keep your space clear and work better with fewer distractions. The DEWALT DWE7490x 10 Inch Table Saw also comes with a push stick included in the kit so you’ll be able to take protective measures when you work. We’d recommend the DEWALT DWE749x to anyone as a good addition to their go to tools. It is an excellent tool and will help you do some of the best work of your life.

Delta has also improved the tabletop geometry on this model which means that you’re going to get more surface area stabilization. The base is also made of durable cast iron and since it offers easy access to the off/on switch, using the Delta UNISAW is a breeze. Other user friendly features include the convenient dust extraction system, large blade opening for easily changing the blade and fine-tuning the riving knife, smart storage for simple organization and fast access.
Brad – Won’t be anytime soon. I’d offer a few thoughts though on this topic. First off, for this type of testing it’s just not feasible for us to do any long term testing that would be required to evaluate your concern. You’re right, most jobsite table saws have less than perfect fence systems. The rack-and-pinion style that DEWALT, Hitachi and some others use are far more accurate over the long haul than the “clamp” style. Lastly, for lots of guys they are transitioning to track saws for work that requires a really precise cuts or they cut critical pieces in the shop. In a perfect world we’d get shop precision out of jobsite saws, but the reality is due to weight limits its unlikely. Thanks for the feedback.
Blade guards are an important safety device and should never be removed from the saw. You want to find one that rises up parallel to the table so it is always on top of the material you are working with. The purpose of this blade guard is to protect you from the spinning blade. While some woodworkers find them annoying, the safety they provide is well worth the inconvenience.
For some table saws, a dust collection system is just a bag that collects the dust generated from your table saw. This might do the job perfectly well for many novice table saw users, whilst others might benefit from a more sophisticated dust collection system. Either way, it’s of paramount importance to make sure that you pick up any dust generated by your table saw, as it could be dangerous in the long term to both you and your family.
Both the riving knife and the blade itself has a quick release design that lets you remove each one in minutes after accessing the arbor lock and without using any special tools either. The blade guard has a similar design that allows you to remove and replace it without any tools. This guard does a good job of keeping your hands and any other body parts safe as you use the saw.
The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. There is tool-less assembly of the riving knife and anti-kickback pawls. It has a large easy to access ...  More + Product Details Close
The fencing should be perfectly straight and parallel to the blade in order to maintain a safe environment and achieve the best results. As soon as the fencing is taken care of, turn your attention to the blade itself. Is it properly adjusted and sitting at a perfect 90 degree angle? If not, you could encounter some issues while trying to work. You’ll need to find an accurate measuring tool to make sure your table saw blade is resting at a perfect 90 degree angle if you want to see the best results.
The differentiating factor is workshop realestate: it takes up nearly 2 square feet less space than its larger, more powerful counterpart, making it ideal for craftsmen with less workspace who don’t need the extra horsepower for cutting heavier hardwood materials. Best of all, it includes SawStops 5 millisecond safety system to protect craftsmen from accidents that can lead to serious and permanent traumatic injuries.
If you’re not sure how to proceed, it’s important to take a breath and think about what you need out of a table saw. You could get a model with every possible bell and whistle, but there’s there no reason to do that if you’re not going to use it frequently. Likewise, you could just buy the cheapest model, but that doesn’t mean it’s going to be a fun machine to use.

The quiet, 220-volt motors in these saws cut through the hardest stock, hour after hour, without bogging down. Cabinets are metal and extend to the floor for the best dust collection. The tops are cast iron, wide, and stable, which makes it easy to cut sheet goods. The trunnions are cabinet-mounted, so you get minimal vibration and maximum accuracy. They're also heavy; some weigh over 600 pounds. Once a cabinet saw's in place, that's where it stays.
×