While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
One of the biggest issues and potential hazards when working with table saws is kickback. Table saw kickback occurs when wood is ejected from the saw at extremely high speed. You can imagine the sort of injuries this can cause. Table splitters are effectively small vertical bits of metal or sometimes plastic that are designed to stop the wood flying back if there is a kickback.  Attached to the splitter are anti kickback pawls either side, they look like table saw blades themselves but they are in fact there to grip the wood at stick into it in case of kickback.
The miter gauge is a part of the unit that moves into the slot. With a miter gauge, you can make a square cross-cut. You just have to set it at 90 degrees and push the board toward the blade. Also, by setting it at 45 degrees, you can make angled cuts. However, when using the miter gauge, make sure the wood is not moving. Secure it to the gauge using a clamp. With a miter gauge, you can also make compound cuts. You just have to set the miter gauge and the level of the blade at the same desired angle.
Both the riving knife and the blade itself has a quick release design that lets you remove each one in minutes after accessing the arbor lock and without using any special tools either. The blade guard has a similar design that allows you to remove and replace it without any tools. This guard does a good job of keeping your hands and any other body parts safe as you use the saw.
There are three areas of importance that you’ll need to protect – your ears, eyes, and arms. To start with, you’ll want to make sure that you have a pair of earplugs or noise reducing headphones that will help to minimize the negative effects of being exposed to loud noise for prolonged periods of time. While this may seem like a small solution, it is something that you’ll want to make sure you take into full consideration – to avoid doing so could be extremely detrimental to your overall health.
Jeffery – As Rob explained things we had the RPM measurements running on that meter, and had to watch our video playback to evaluate the numbers (no recording of the numbers digitally). So we tried to take the average no load speed watching the video play back. Is it perfect? No….is a 10% difference a big deal? In this application I doubt it. If we were a full blown testing lab we’d have the data recorded digitally and take full blow averages, but alas we are not.
The 708494K JPS-10TS from Jet Proshop is a high end cabinet table saw which delivers on all your expectations. Available in either a thirty inch or a fifty two inch rip capacity, this model is built from cast iron and is extremely rugged in order to withstand a lot of abuse and still deliver the excellent results you’re expecting from it. Regardless if you’re a professional or if this is the first cabinet table saw you’re planning to get, the 708494K JPS-10TS won’t disappoint. Its rugged build quality and ease of use are going to make it one of the best table saws currently available.
Additionally, the W1819 also features a miter fence with flip stop for precisely angled cuts, and the blade can even be tilted left up to 45 degrees for angled cutting when working with bevels, compound miters and chamfers. Furthermore, the fence can be camlocked to keep it steady when making complicated cuts. There are few professional grade table saws that can match the ShopFox 1819 for power, performance features and control. Overall, it makes a fine addition to any working or hobbyist wood shop.

The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.
Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.

When you need a full size cabinet saw that can handle just about any woodworking job you can throw at it, the Powermatic PM2000 is the one for you. As with all high end cabinet saws, the PM2000 features box-style cast iron trunnions for that refined, precise feel when adjusting the blade angle and height. Front control wheels are user-friendly cast iron hand wheels that feature precision-machined center locking pins for making every cut consistent and repeatable.
If you’re looking to squeeze the most possible power out of your table in terms of both strength and precision, it’s a cabinet table saw that you’re looking for. They’re what’s seen as a traditional table saw and the variety that most professional wood cutters use on a day to day basis. However, as the name suggests, this raw power and precision comes at the cost of portability. It’s pretty clear that cabinet table saws are designed to sit in one place and be used as a tool within a workshop environment.
No matter what you need a table saw for, the three listed above are great choices to consider when you’re doing your shopping around. Whether you’re a professional contractor or a serious DIYer, any one of them will have all the features, power, and portability that you could want in a table saw. All of the ones listed here, and most others have warranties and 30-60 day money back guarantees to give you a chance to see if you like them so your purchase won’t be a waste if you don’t, you will be able to get your money back, but we’re pretty sure that if you choose one of the three that we have detailed for you, you’re going to be able to join the many, many customers who are very happy with their purchases.
The final brand that’s definitely worth a mention when it comes to evaluating the brands we’ll be featuring in our table saw reviews is Ryobi. They’re largely known for manufacturing components for use in the automobile, electronics and telecommunications industry. However, they’ve more recently branched out into their own range of power tools and other hardware related tools, including table saws. With that taken into consideration, from our experience of Ryobi’s products, we’d definitely say that they’re a brand well worth keeping your eye on.
The latest advance in table saw safety is a feature that stops the spinning blade when it senses the presence of tissue, such as a finger or forearm. A company called SawStop was the first to offer this technology, and currently, it holds the exclusive right to sell saws with this feature in the United States. (Bosch introduced a portable table saw with blade-stopping technology in 2016, but was forced to take it off the market after a successful patent-infringement suit by SawStop.) In 2017, the CPSC proposed a new rule to make SawStop's technology mandatory on all table saws, but that rule is still under review. See the Buying Guide for more information.
The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
That being said, because of their portability, you’ll find that this type of table saw tends to be less powerful than other more permanent saws. This is because they have less power and less noise muffling too, so you’ll find them to be louder. What’s more, because of that aforementioned lack of power, you might find that you’re unable to use the law to cut through certain materials. This shouldn’t put you entirely off a portable table saw though. For many users, they offer the best of both worlds and provide the complete sawing experience that they need from their table saw. Portable Table Saws
The thing you might not like about it is the non-flat table top. Many people find this downside as quite a burden, especially if you’re processing perfectly flat wood. Also, the protective coating on the top side of this model is pretty subpar. In fact, it barely protects anything. Consequently, it will peel off quite quickly. As far as the price goes, it’s okay, but it could have been a bit cheaper.
Designed to be Portable – In case you hadn’t already gathered from the above section, this is a table saw from Bosch that is clearly designed to be portable. If you’re going to need a table saw that can be moved on and off of a worksite with little effort, you’ll definitely find that to be the case with the Bosch 4100-09 and it’s included Gravity Rise Stand.
If you are new in this industry, you need to know one important thing. Every model is equipped with a motor. The amount of power and the motor are strongly related to the project you have. In simple terms, it depends on what you are cutting. For example, a 2 hp motor can easily rip wood of 2 inches thick, while other hard materials require a 5 hp motor. Keep in mind that the 5 hp motor is found only on cabinet saws.

Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.


Delta 36-L352 10 in. contractor table saw is a heavy duty table saw. This big guy is no joke! Its 15 A, 3 HP motor is not only powerful but smooth. This Delta table saw also has a HUGE rip capacity of 50-52 in. and an 82 in. table, so there won’t be much this table saw can’t handle. Its integrated BIESEMEYER fence system, precision bevel gauge, and bevel dial work together to help you get highly accurate cuts down to the nearest 1/4 degree and 1/64 in. Now that’s accurate! Other notable features are its bi-level dust extraction system which helps you keep your workspace clean, large blade opening, and SURE-LOCK dual front cranks for easy access. This table saw is ideal for the pros.
One thing manufactures noticed over the years was that when people used the splitters in normal straight cuts it worked well but it’s biggest downfall came when contractors wanted to do cross cuts. What would happen is that people would remove the splitters to make the cross cuts but then forget to fixed them back in place. One brilliant table saw safety feature is the riving knife. The Riving knife is attached directly to the blade mechanism, this allows it to always be attached not matter where or what angle the blade is.
This Portable Table saw includes an industry standard This Portable Table saw includes an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. It has a Tool-less assembly for the riving knife and anti-kickback pawls. It's perfect for mobile contractors and the Do-It-Yourself ...  More + Product Details Close

A table saw is the centerpiece of any home workshop, and it’s often the very first power tool to be cranked up at the start of any woodworking task. They’re essential for the necessary task of sizing wood for each project – whether narrowing the width of boards, cutting plywood sheets, or tackling specialized cuts like grooves, slots, and tenons. Because of their important role in DIY and professional construction, choosing the right table saw is critically important. At BestReviews, we’ve researched table saws in depth. We’re here to help you decide which type of table saw will best meet your needs.


Most table saw blades come in 8, 10 or 12inchs in diameter, but you can also get a lot smaller and larger sizes if you require special cut sizes and cut depth sizes. When looking for a new blade when it comes to sizes, blades are measured in two sizes mainly, the mounting hole and the total blade diameter, make sure you take the mounting hole size in to consideration when buying a new blade as this could be something very easily over looked but could cause an issue.
It’s a challenge to identify the best portable table saws. They need to be the right mix of quality, performance, price, brand, and availability. In this article, we will attempt to cover all those points for our five tops picks in this burgeoning market sector. Our reviews are designed in a way that can help you concentrate on products that provide a pretty comprehensive package. While the market is full of options, it is always good to go for ones that highlight the unique versatility of this tool. We will also go over everything you need to know in our buying guide so that you can purchase a portable table saw with confidence.

A cabinet table saw is so named because it has an enclosed style base. This saw is the opposite of the contractor saw. Cabinet table saws are designed to be functional and lasting to meet the qualifications that are required by people who work with wood for a living. They are constructed to be more durable than contractor saws. Makita table saw offers many popular options at a very affordable price.


The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.
Stands are one of those features where the ends really do justify the means. Some made us wish the manual writers would take a cue from Lego—just make the *@#$! things easy enough for a 7 year old to understand. That aside, SawStop set itself aside brilliantly, taking just 10 minutes to setup. All we had to do was install the wheels and two handles. Even the packaging is designed to make the process easier and the instructions were super-easy to understand. Makita was nearly as simple only requiring us to install the handle and bolt the saw to the stand.
My son Owen and I thank you for the truly wonderful, informative and entertaining experience provided by the TOH staff, crew and trades-people at the Pro2Pro Brookline event. From Elizabeth - who welcomed us to the event, to Chris, Kevin and others who were wonderful during the orientation session (answering questions that I'm sure you have heard dozens of times before), to Charlie, Kevin, Richard, Heath (the electrician) and Thomas (the program director), you helped us Insiders to understand and appreciate the pride that you take in your work. It was refreshing. I loved the pictures and accompanying text of the event that you posted. I have to say in closing to Chris, Kevin and Thomas (in particular) you gave my son, a budding landscaper, the impetus to continue his pursuit of the trades. Kudos to you all and keep up your great work!
×