While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.
The stand is collapsible and wheeled like others, but it’s not the gravity-rise style. You’ll have to use a foot to stabilize it while you pivot it up or lower it down. The lower locks are released with your feet and there’s some question about the long term durability of the releases. An open housing design has two major results – motor cooling should be more efficient but it trades off storage for an extra blade. There’s really way too much to talk about here, so check out our full review of this model.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
An idea for next time you do a table saw review – what’s most important to me is REPEATABILITY of adjustments. Same for the fence – I want to know that, wherever I set it, it’s ALWAYS accurate and straight. I’m OK if the saw needs some tuning up out of the box – most saws do – but I really want to know that I can trust the saw to HOLD its adjustments, especially if I’m moving it around a lot. This I find is the weakness of jobsite saws in general – they just don’t STAY accurate for very long as vibration and just moving them around jar things out of position. Essentially, I want to know which of these saws is going to need constant fiddling, vs which ones ‘just work.’ with minimal fuss.

For homeowners without the luxury of a huge garage to fit their enormous table saw, DEWALT’s DWE7480 is a compact alternative to bulkier machines with the same wood slicing power. Measuring 25.8" x 26.5" x 13.9", the DWE7480 hosts a 15-amp motor that cuts at an unbelievable 4800 rpm with a ten-inch blade, meaning this small package packs big performance — and with adjustable rear feet that are designed to allow users to level their table saw on uneven surfaces, you’ll be sure to get a clean, precise cut every time, no matter how rugged the terrain. An additional dust port makes collecting your sawdust a breeze — especially if you attach an optional shop vac extension.
The compact saws are a bit more advanced than the bench top saws. They are equipped with plenty of impressive features and characteristics including direct-drive motors. In spite of their lightweight feature, most compact saws are powerful and provide a lot of benefits. With additional features like stands and extra surfaces made of cast iron, most of them resemble full-size models. However, they still have a rip capacity much smaller than other saws.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
It’s interesting to note that if pricing was taken out of this evaluation the ranking would have been: DEWALT in first, Makita in second, Hitachi, Skilsaw and SawStop tied for third, Bosch in fourth, Delta in fifth and Ridgid in sixth place. But at the end of the day price is certainly a factor. What we didn’t do in our evaluation is any long term testing to look at durability which ultimately could affect your purchase decision as well.
Every woodworker needs a tool to make furniture and build cabinets. The wood cabinets are vital in any building because they increase the storage capacity of any room. Whether small or big, a cabinet should be done only with a quality model. This powerful tool is capable of cutting big pieces of wood into different sizes and shapes for building cabinets and making furniture.

These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.

A high performance saw for the most complex of woodworking jobs, the JET XACTASAW Deluxe lives up to even the most demanding of working conditions and craftsmen expectations. Both the trunnion and table are made from heavy duty cast iron to virtually eliminate vibration while cutting, and 29x42 inch workspace allows plenty of room to maneuver large workpieces.


TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.
If you are an avid hobbyist, this saw is made just for you. The company is known for its uncompromising quality and durability. This saw has a safety system where the blade stops and retracts automatically when it comes into contact with anything that is not wood.  The microblade guards keep debris from flying all over your workshop. It is easy to change between blades. You will not require a riving knife to do this. Its award-winning dust collection system ensures that you have a clean and presentable workspace at the end of the day.
Another indication of how hard a table saw is working is monitoring the amperage (AMP) draw under loading conditions. We measured the amp draw for each saw using all three materials again at the same time we were recording RPMs. The first graph below shows the amp draw for each saw cutting plywood compared to the no-load amp draw. The white bar on the left indicates the no load amps and the colored bar on the right shows the maximum amp draw during the cut.
Flesh Sensor: This is another very important safety measure. While it is possible that this might raise the cost of the saw, nothing is more important than your good health. Flesh sensors stop the blade immediately when they sense a finger on the blade. So instead of a severed finger, you get away with minor cuts. Always choose minor cuts over missing fingers! You do not want to be going to the emergency room with an ice box.
At a compact 45 pounds, the DEWALT DW745 Compact Jobsite Table Saw is the lightest table saw in our review. The saw's portability doesn't mean that ripping size is compromised, though. Thanks to extending fence guides, you've got 20 inches available. Depth of cut is on par with many bigger machines: at 90 degrees, it's 3 1/8 inches. At 45 degrees, it's 2 1/4 inches. Power comes from a 15-amp motor with a no-load speed of 3,850 RPM. This is ample enough for serious DIY projects and light-duty construction site work.
If you’re a DIY enthusiast, you’ll definitely find something of interest. On the other hand, professionals can also find good pieces of information on this page. The models we’ve covered all work as advertised, and you can rest assured that they are of high quality. The only thing you need to do is determine how much money you want to spend and which type is the best suiting one for your requirements.
Once you’ve made sure that the table saw is unplugged and there aren’t any extra materials in your workspace, you should turn your attention to the miter slot. See also related: Top 10 Miter Saws here. You’ll want to make sure that the miter (click here for sliding miter saws) slot is parallel to the blade. It is important that all measurements are precise and exact – nothing short of parallel will do. Once you’ve measured the blade and the miter slot, you’ll need to check the fencing as well.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2019. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here

Every woodworker knows the plague of working in a dusty environment. The SawStop has a fantastic dust collection system so you can enjoy your cutting without your eyes being strained. Almost all of the dust is wicked away both above and below the table. Up above, the blade does all the legwork and there’s a neatly designed shroud which pulls all this dust away from the blade. The 4-inch port means you can slip your shop vac on with no issues.        


Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.

Contractor saws are a perfect balance between functionality, manoeuvrability and price. These sorts of saws are perfect if you have bigger projects that you’re working on and will stay on site for a few months. This is due to the fact that they are a lot less portable, but that being said they are a great in-between saw as they still have great rip capacity and overall cutting power.

Craftsman 10 table saw Craftsman Radial Arm saw 10Craftsman 16 direct drive scroll saw Chicago Electric 10 compound Slide Miter saw Wagner power painterBlack and Decker rotary saw and jig sawCraftsman corded drill. Craftsman 10 compound miter saw.Cleaning out my shed and am trying to downsize. $550 or best offer and its all yours. Ill help load but wont deliver. Great Christmas gift for that ha...

Just in time!!! My Sears Craftsmen portable saw died on me last week. It was only 12 years old with minimal use. It was a nice saw with a nice sized table, not heavy, and a stand that separated and folded like an accordion. Unfortunately, as it turned out, the gear teeth on the worm drive had worn down to the point where the saw started slip and whine. Now that Sears is defunct (Canada), I have no other option than to replace it due to no parts being available.
Purchasing a quality model is one of the most important investments of a wood-worker. It is a necessary item that is seen in every woodcutter shop. Without this equipment, you won’t be able to complete all your projects based on the hardwood. We all agree that this is a dangerous tool. Also, after doing some research we can truly say that it causes several injuries to the user. However, it also has a lot of advantages besides this drawback. Therefore, in you are interested in finding out more about the advantages of using such a tool, take a look below.
If you're currently looking for a cabinet table saw and it's the first time you actually need to buy one, then you should know that they come in a wide range of types, from the larger contractor saws to the portable table saws that most people seem to own. However, buying the right model for you depends on your needs and how you're going to use it.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
I see the ovens next to 'fridge. Isn't that a no-no? The heat from the ovens make the 'fridge run to cool more when the ovens are used, upping the electric bill. They are also too far from the center of preparation. I would have put them against the long counter. It would also allow counter space by the fridge to place items when putting them in or taking them out of the 'fridge.
×