It’s often overwhelming when looking for new power tools and products online. So many features, specs and brands etc to research and review. So, what should you look for when buying a new table saw? One thing we always mention is to make sure you read as many table saw reviews as you can before purchasing one, this will insure you have the best table saw for your requirements.
The miter gauge is a part of the unit that moves into the slot. With a miter gauge, you can make a square cross-cut. You just have to set it at 90 degrees and push the board toward the blade. Also, by setting it at 45 degrees, you can make angled cuts. However, when using the miter gauge, make sure the wood is not moving. Secure it to the gauge using a clamp. With a miter gauge, you can also make compound cuts. You just have to set the miter gauge and the level of the blade at the same desired angle.
The Skilsaw SPT70WT-01 is a super high quality table saw with the power to match. The Diablo blade that comes with it will cut through 4×4 without any problems at all, like a knife through butter! One of the best features we noted was the fact that there is barely any vibration, this allows to you to cut as straight as an arrow, you can really feel the build quality with this saw.It has an extremely easy to use miter gauge, just a flick of the wrist to change the angle of cuts to exactly what you want.
Though this Jet 708674PK XACTASAW Deluxe 3HP Cabinet Saw comes with the same three-horsepower motor found on the last cabinet saw, it comes with a shorter 30-inch rip fence that may be a little too short some of your projects. It features all the same great features that made Jet so popular with contractors, including a cast-iron enclosed cabinet that stops dust from entering the motor and a poly-v drive belt system that runs more quietly than other belt systems.
A table saw has two main ways it can seriously hurt you. One is obvious and that is having any part of your body come into contact with the blade. Any table saw you are seriously considering should have a blade guard installed. The clearer the better. And make sure you leave it on. The blade guard can’t do its intended job from a workbench or shelf.
So what should you do? The good news is, you don’t need to rely on budget tools to get you through your projects anymore. All you need to do is set aside some time to do some research and investigating so you can find a tool that truly fits your needs. And luckily for you, we’ve taken the time to compile a list of the top 10 best table saws that you can invest in for your woodworking projects.
Jet has a strong reputation for providing customers with durable power tools that operate just like professional models but cost less, and that is definitely true of this 10-inch table saw that comes with a riving knife. You’ll like the basic design of this model, which has an intuitive design that allows you to set it up and start cutting faster. It features both a solid cabinet as well as an extension table that stretches out from one end.
Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.
On the other end of the handyman spectrum, you’ve got the seasoned professional with years of experience under his belt. We all know the type: he’s the guy that expects only the best, and DEWALT more than delivers with their patented DWE7491RS. This wood-slicing machine is the cream of the crop when it comes to cutting through even the toughest materials. The DWE7491RS measures 26¼" x 22", so it’s a relatively large apparatus — you’re going to want to make sure that you have plenty of space in your garage for this table saw.
It’s worth remembering that contractor table saws are still going to be pretty portable because they’re designed to be used by contractors. That being said, unlike portable table saws, they don’t necessarily fold up into a compact position. This is largely because contractors tend to have the facilities needed in order to transport a larger bit of kit. The extra space that they take up in comparison to a portable table saw means that contractor table saws are able to offer a greater level of power and precision. Both of these points further support the fact that contractor table saws sit in the middle ground.

Perfect for both hobbyists and craftsmen, the PCS31230-TGP252 from SawStop is a 3 HP cabinet saw that delivers excellent performance while featuring the company’s patented safety system to ensure maximum safety during use. The safety system is similar to that of the G0690 from Grizzly where the blade stops in milliseconds after it comes in contact with flesh. Designed and built in order to satisfy the needs of the most demanding users, the PCS31230-TGP252 features an exacting finish and feet and a superior dust collection system. For increased precision and added strength, the PCS31230-TGP252 features a fifty two inch T-Glide fence system, but also an extension table and rails.


Safety Features: All said and done, you have to accept that the portable table saws are amongst the more dangerous tools to operate. If you are not careful, you can easily get hurt. This makes the safety features some of the most important to consider. I would keep an eye out for features like anti-kickback pawls and blade tilt as they go a long way in avoiding accidents. Most also come with a magnetic switch that makes sure that the machine does not get started on its own accidentally. This is essential. Do not buy a portable table saw without a magnetic switch.

The biggest thing that is making me watch less and less is the fact that most people will never use half the products you do. Like the Lattice. 99.9% of your viewers will have to use store Lattice as cost is to be considered. I estimate that each piece of Lattice you put on this house costs about $50 finished. Multiply that by 20 sheets and your at a cool $1000 for your Lattice. Most of us would go to the store and purchase 10 Lattice sheets for about $300. 10 sheets as each make up two panels. It would be really nice, for a change, that you would fix up a house the same way most of us would. Probably the reason Ask This Old House has out classed This Old House.
All of these great features, combined with the cast iron table top make this saw a tool to be reckoned with. The  SKIL 3410-02 10 Inch Table Saw has a 32 inch rip capacity. You’ll be able to easily and efficiently make cuts by implementing their EZ measurement system. All you have to do is line up your wood and focus on doing the work you love. It’s easily transportable, easily adjustable, and easy on your bank account - and really, what more can you ask for in a tool?
Methods for tilting the blade to cut bevels vary among the saws. The Porter-Cable saw is the only one with a conventional handwheel bevel control mounted on the side of the saw. The crank gives you great control for setting an exact angle. To set the bevel on the Bosch, DeWalt and Rockwell saws, you simply release the bevel-lock lever and tilt the saw to the preferred angle. It’s easy to go quickly from a 90-degree to a 45-degree bevel with this method. The Ridgid, Craftsman and Ryobi saws have a rack-and-pinion setup. These saws utilize the front crank for setting the bevel.
Blade guards are an important safety device and should never be removed from the saw. You want to find one that rises up parallel to the table so it is always on top of the material you are working with. The purpose of this blade guard is to protect you from the spinning blade. While some woodworkers find them annoying, the safety they provide is well worth the inconvenience.
Thanks for reading the fine print. About the Wiki: We don't accept sponsorships, free goods, samples, promotional products, or other benefits from any of the product brands featured on this page, except in cases where those brands are manufactured by the retailer to which we are linking. For our full ranking methodology, please read about us, linked below. The Wiki is a participant in associate programs from Amazon, Walmart, Ebay, Target, and others, and may earn advertising fees when you use our links to these websites. These fees will not increase your purchase price, which will be the same as any direct visitor to the merchant’s website. If you believe that your product should be included in this review, you may contact us, but we cannot guarantee a response, even if you send us flowers.
Our table saw review quickly showed that today’s portable table saws are light-years ahead of the small-saw offerings from a decade ago. They feature big-capacity cutting, greatly improved safety features and attached stands for easy setup. And saws in the upper price range rival stationary saws in accuracy and quality of cut. We limited our review to saws that included a stand with wheels and ones that could rip at least 24 in. wide, only the best table saw for our readers!

Probably one of the things that users will love most about this table saw is the solid granite surface which offers a seamless work area and excellent support. Another advantage of the Steel City 35955 is the fact that it comes with powerful magnets which allow swift changes without having to worry about using any type of tools. Since there’s a built-in mobile stand, you can easily position the saw around your shop without requiring the help of a second person.

Ergonomics is the science of designing and producing tools that improve a worker’s efficiency while reducing discomfort, fatigue, and risk of injury. Ergonomically enhanced tools can include helpful features such as angled handles, riving knives, safety switches, and non-slip coatings. Whether you’re shopping for ergonomic tools or just trying to select the right one for the job from an existing collection, the key things to consider are whether or not the tool eases your work and prevents you from straining in ways that could lead to injury. Ergonomic guidelines in tool design can help maximize human performance on the job by making the job easier for the worker, improving safety and decreasing injuries.

The Shop Fox W1819 is our top table saw, due to its phenomenal power and great safety features. The DEWALT DWE7491RS was the best pick under $1000, due to its excellent power and portability. The Bosch 4100-09 was third on our list, featuring electronic speed control and easy blade changes. The DEWALT DW745 was the best for the money, as a smaller version of the DWE7491RS that packs the same amount of power. The Craftsman 21807 was last on our list since it has severe precision issues.

What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.


The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
Goggles are yet another thing people simply don’t like wearing. However, it’s not about comfort but saving your eyesight. As you can assume, there is a lot of sawdust flying around while you’re cutting a piece of wood. In order to prevent it from flying straight into your eyes, you have to wear safety glasses. There are hundreds of models you can choose from, but make sure they are certified as safe. In simpler words, you cannot use the first ones you stumble upon, don’t be afraid to invest in high-quality safety glasses, you’ll be thankful for them.
You want to rip down lumber with your table saw. For this you’ll need a fence. You just can’t make an accurate rip cut without one. Check the fence sits on the rails firmly. You should be able to adjust it easily in both directions. A T-square fence is the most common type. Made from welded steel, it’s precise, user-friendly and durable. Some fences are mounted with bolts. Others are welded onto the head of the T-square. Miter gauges are priceless for making cross-cuts and other more advanced cuts. This gauge acts as a guiding device. It moves in the miter slot. You can angle between 45 degrees and -45 degrees. For angled or square cross-cuts or other specialty cuts, a miter gauge fully delivers.
When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.
Furthermore, the split guard offers a tool-free riving knife that moves freely via a front level control for on-the-fly adjustment. Pawls and splitter guards can also be added to the riving knife without the need for tools as well. Best of all, the 36-L352 includes a 52-inch Biesemeyer Fence System that has an integrated tape and a hairline pointer for consistent and repeatable cuts every time. If you don’t work with wood that needs the additional horsepower of 36-L552, this version of the Delta UniSaw is definitely for you.

The continuous-read, tape measure–type scale is ingenious and easy to read, and Ridgid’s lifetime warranty covers it against breakage. The Ridgid saw has the most versatile miter gauge with holes and slots for mounting extensions and accessories. The designers have cleverly fashioned the stand to also serve as a left-side outfeed support for ripping plywood.
The first contractor saws were made to be portable so they could be taken to job sites. These are also lightweight and priced low enough that the handy homeowner can use them. When purchasing the contractor saw there, you will have to make a few concessions. The table is not made of the cast iron top and the extensions are usually made of stamped medal. It is not made as burly as more costly saws. The motor also hangs off the back, which makes it easier to remove when moving the saw to another job site. Bosch table saws are reported to be one of the best budget saws available.
You want to rip down lumber with your table saw. For this you’ll need a fence. You just can’t make an accurate rip cut without one. Check the fence sits on the rails firmly. You should be able to adjust it easily in both directions. A T-square fence is the most common type. Made from welded steel, it’s precise, user-friendly and durable. Some fences are mounted with bolts. Others are welded onto the head of the T-square. Miter gauges are priceless for making cross-cuts and other more advanced cuts. This gauge acts as a guiding device. It moves in the miter slot. You can angle between 45 degrees and -45 degrees. For angled or square cross-cuts or other specialty cuts, a miter gauge fully delivers.
We spent over 30 hours researching and testing 10 different brands of table saws and found that maximum speed, cord length, and cut depth were most important. The DEWALT DW7480 table saw scored high marks in every category and is our top pick. This 48 pound table saw is perfect for using at home or taking with you to the job site. It has a powerful 15 amp motor and 24” rip capacity that makes it a favorite with everyone. The 2 ½” dust collection port allowed us to connect the saw to a shop vac and reduce the amount of dust that was in the garage.
Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.
Other than that, this is a great portable saw. It is lightweight and easily moved from location to location. It also has a pro guarding system that basically allows quick and easy adjustments. It also has a metal roll cage to help with durability. Furthermore, it has built in storage which is always welcome. That is a lot of features at this price point!
TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.
Miter gauges are one of those accessories that you may forget about in daily use, but then desperately need if you don’t have one. They’re used with table saws in order to cut angles that aren’t 90 degrees. The best miter gauges include hard stops at 90 degrees and 45 degrees, which are the angles that you’re most often going to be cutting at. The hard stops make it easy to set the miter gauge to those angles and cut away with confidence.
If you are an avid hobbyist, this saw is made just for you. The company is known for its uncompromising quality and durability. This saw has a safety system where the blade stops and retracts automatically when it comes into contact with anything that is not wood.  The microblade guards keep debris from flying all over your workshop. It is easy to change between blades. You will not require a riving knife to do this. Its award-winning dust collection system ensures that you have a clean and presentable workspace at the end of the day.
To make our recommendations for the best table saws, and the best table saw bargains, we consulted comparison tests and single-product reviews in tool-related publications such as Pro Tool Reviews, Woodworker's Journal, Popular Mechanics, Tools of the Trade, and Fine Homebuilding. Many of these reports are several years old, but most of the models tested are still available. Most professional reviews focus on portable table saws, but we found a few that cover contractor and cabinet saws.
Today's table saws also include riving knives, which ride up and down with the blade when its height is changed, rather than splitters that are fixed in place. The problem with the old splitters was that they had to be removed for certain types of cuts, and users might forget to put them back on before making rip cuts. This increased the risk of kickback injuries, which occur when the spinning blade kicks back a piece of wood toward the user with tremendous force, causing serious injury to any part of the body that's hit.
The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.
All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
×