The accuracy and safety of any given saw is dependent upon the blade being parallel to the rip fence. Since we tested the amount of difference in parallelism between the saw blade and the miter slot in the previous test, we need only to see if the miter slot is parallel to the rip fence to see if the saw has a parallel relationship between the blade and the rip fence.
Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.
One of our favorite features of the device however, would have to be the load speed and maximum cutting depths. The DEWALT DWE7480 Compact Job-Site Table Saw can reach a load speed of 34,800 rpm and can reach a maximum cutting depth of 3 ⅛ inches when working at a 90 degree angle and 2 ¼ inches when working at a 45 degree angle. You’ll love the quick and accurate cuts you’ll be able to make while using this device - it will revolutionize the way you’re able to go about your job.
There are three areas of importance that you’ll need to protect – your ears, eyes, and arms. To start with, you’ll want to make sure that you have a pair of earplugs or noise reducing headphones that will help to minimize the negative effects of being exposed to loud noise for prolonged periods of time. While this may seem like a small solution, it is something that you’ll want to make sure you take into full consideration – to avoid doing so could be extremely detrimental to your overall health.
Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
While we rotated the plate, we recorded the maximum reading on the dial indicator. We validated each maximum reading by running the test for a second time and noting that the readings were consistent. TBB also noted that as we performed these tests on all eight saws, the maximum readings occurred at different parts of the plate along its rotation. Because the max readings were in different and discrete parts of the calibration plate, TBB had a very high level of confidence in the flatness of the calibration plate, itself.
To learn about how table saws perform in real people's homes, we consulted owner-written reviews at retail sites like Amazon, Home Depot, Lowe's, and Sears. User reviewers don't have the breadth of experience that many experts enjoy, but they can provide keen insights on the model they bought, including things that might not crop up in the relatively short time professional reviewers have to spend with a given saw.
"This is the best table saw I've ever laid my hands on (no really it is). Coming from a Craftsman job site table saw, there's really no comparison between the two so it wouldn't even be fair to try. As a hobbyist, this saw is a little bit of overkill for what I do but having the peace of mind knowing my fingers will have a fighting chance in the event of a blade contact, It's well worth the money. Safety feature aside, it's still an amazing saw." - Hoang - Rockler.com Customer Review

Lightweight: Typically, you want to choose a portable table saw that is relatively lightweight but sturdy. This will make sure that you are able to work faster and more efficiently compared to heavier options. It also cuts down the strain involved in using this tool as well in moving from one location to another. While looking for lightweight options, do not compromise on the stability element though. If your table saw is not sturdy, it can easily be wobbly while cutting the wood or other material. This is a safety risk but also will end up with junk projects and mistakes. Woodworking is all about precision, and that requires stability.

The Craftsman table saw is one of the most compact of the bunch when it’s folded up. And if you can get it for the sale price of $260, it’s also the cheapest of the best table saw options. The blade guard and anti-kickback pawls are identical to the Porter-Cable and are the hardest of any of the saws to install. And they are the only two blade guards that don’t have a feature to hold them out of the way when you’re adjusting the blade or setting up the cut.

Consequently, they’re going to be a bit heavier than benchtop models. However, their expanding frames mean that you’ll be able to use them even in places where you don’t have access to a table or bench. This is great for construction work, or situations where you’re going to be working outside. This type tends to be a little bit bigger than the benchtop variety, and often has more rip capacity as well.

With that in mind, you can likely imagine that hybrid table saws are perfect for those looking for greater power than that offered by a contractor table saw, but don’t fancy paying anything around the price of a cabinet table saw. At the same time, whilst hybrid table saws are nowhere near as portable as some of the aforementioned options, you should still be able to find that they can be transported when necessary. When it comes to the middleman of table saws, that’s a title truly deserved by the hybrid variety. In all, if you’re looking for a bit more power than that offered by a contractor table saw but don’t fancy paying the price of a cabinet variety, this is an option well worth your looking at.


If you are interested in buying a new model, then do not hesitate to read the following lines. Before making a purchase, you need to consider several things. Rip, miter, bevel and cut are just some of the things you will be able to do with this tool. More than that, you can amplify its functionality by adding several accessories to it. As compared to traditional saws, the circular saw has the ability to move the material towards the blade, which means a much more precise cut. However, in order to help you find a unit that meets your requirements, here are some of the most important things to look for.
15 Amp Motor – If there’s one thing that you’ll learn from this website’s table saw reviews, it’s than I order to for a table saw to be effective, it needs to be pretty powerful. With an included 15 amp motor, we can quite comfortably say that this particular product meets that specification. In fact, you should find that the motor is able to easily rip through hardwoods and just about any other type of wood.

The obvious starting point for an analysis of which saw is best suited to the needs of a given person (or company, school workshop, and so forth) is the budget at hand. Even the most affordable table saws of a quality meriting serious consideration cost more than 200 dollars; such units are small but still capable of many tasks. The top of the line table saws come with price tags topping out at well over 3,000 dollars and can handle almost any lumber you would ever need cut and then some; more often than not these mighty saws are more tool than needed, so to speak.


The same fence system that comes on our number one choice, which lets you change the angle of the wood and make various cuts, also comes on this SawStop ICS31230-52 3HP 230V 60Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System. Designed use in any type of work space, it runs quietly to let you do your work without disrupting others, and it features the same safety system to shut down the saw when it touches any skin. Weighing more than 700 pounds, this is the type of cabinet saw that you can use in the same spot years.

If you are making a cut that will require your hands to get close to the blade, (within 6 inches) use a push stick or two to eliminate the chances of your hand touching the blade. If this is a big concern for you, maybe consider a saw that uses flesh detection to stop the blade. The additional cost of the saw will be instantly appreciated the first time you need it.
Makita joins DeWalt with an external riving knife release so you don’t have to reach into the throat to loosen it. We actually ran into an issue with the design because of a slightly bent plate holding the knife in place. That aside, the intent of the design is sound and should make for an an easier experience. Because of the external release, Makita screws down the throat plate in place. You should only need to get in there for blade changes if everything functions properly.

One of the most widely used power tools for carpenters is the table saw. For carpenters that don’t work exclusively in the shop a portable jobsite table saw is essential. For this Head-to-Head we’re focusing on corded portable 10″ jobsite table saws. We are not including cordless table saws in this test as we plan on doing another head-to-head exclusively for cordless table saws later this year as several are available now.


The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.
In terms of the safety features that you’re going to want to look for in your table saw, one of the most prominent includes a flesh sensor. This is basically designed so that the table saw will immediately stop operating after 0.01 seconds of coming into contact with flesh. This means that if the worst should happen and you come into danger as a result of using a table saw, the damage will be kept to a minimal. As you can likely imagine, this particular safety feature will push up the price of the table saw by a small amount, but it’s definitely a feature that’s worth happening if you value your safety whilst using power tools.
You’ll be able to keep your space clear and work better with fewer distractions. The DEWALT DWE7490x 10 Inch Table Saw also comes with a push stick included in the kit so you’ll be able to take protective measures when you work. We’d recommend the DEWALT DWE749x to anyone as a good addition to their go to tools. It is an excellent tool and will help you do some of the best work of your life.
We took all of the data from the RPM and AMP measurements and added them to come up with the final performance rankings. For each saw we added up the total percentage decrease in RPM’s (for each material type) and added that to the total percentage increase in AMP’s (for each material type). This gives us a relative comparison of each saw over all 6 sets of data.
The first is how easy the switch is to operate. Oftentimes, you will approach your table saw with your hands full especially when we are talking about sheet goods. And sometimes you’ll be making cuts that require both hands to be occupied. Now if something goes wrong or you need to turn the saw off for any reason, you need to be able to do so and the quicker the better.
TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
​The saw does not easily detach from the stand. Sometimes it’s beneficial to set the saw up as a bench-top saw, but the DeWALT 7491RS doesn’t come with quick release levers to accomplish this easily. In this case, you would have to use a drill to remove four screws to detach it from the stand. I wouldn’t recommend doing this unless you have to because over time the screw holes will strip.
As mentioned, the look is similar to a hybrid with a full enclosure. Looks can be deceptive, though… The core design purpose is for this saw to stand up to constant heavy use in a commercial setting. This is not a tool you buy for casual woodworking at home.These bulky, heavy units are built to last the distance. They can weigh up to 500 pounds. You’ll get an accuracy and rigidity not available in lesser types of table saw.Other table saws call for regular adjustments. With a cabinet saw, you won’t need to do this as often once it’s set up properly. 240V motors developing 3-5HP mean there’s very little the best cabinet table saw won’t rip through with ease. Large sheets of hardwood are no problem at all.
Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
The other kind of portable table saw is the wheeled/folding leg variety. The wheeled models come with wheels that can be used to roll them for place to place. The folding leg variety may or may not have wheels. Both models feature a mechanism by which they can be raised up and used without a table. This is what sets them apart from benchtop models.
Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.
The first is how easy the switch is to operate. Oftentimes, you will approach your table saw with your hands full especially when we are talking about sheet goods. And sometimes you’ll be making cuts that require both hands to be occupied. Now if something goes wrong or you need to turn the saw off for any reason, you need to be able to do so and the quicker the better.
The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.
Flesh Sensor: This is another very important safety measure. While it is possible that this might raise the cost of the saw, nothing is more important than your good health. Flesh sensors stop the blade immediately when they sense a finger on the blade. So instead of a severed finger, you get away with minor cuts. Always choose minor cuts over missing fingers! You do not want to be going to the emergency room with an ice box.
So what should you do? The good news is, you don’t need to rely on budget tools to get you through your projects anymore. All you need to do is set aside some time to do some research and investigating so you can find a tool that truly fits your needs. And luckily for you, we’ve taken the time to compile a list of the top 10 best table saws that you can invest in for your woodworking projects.
A table saw can be classified in many ways, and I’ve come across terms like contractor, folding, featherboard, hobby, induction, sliding and zero clearance. However, I will conform to the most basic and clear classification and range the tables accordingly. That means I’ll order them by benchtop table saws, jobsite table saws, cabinet saws and hybrid table saws.
×