At the same time, it’s also worth mentioning that Ryobi offer some of the most affordable products that we’ve seen from many table saw manufacturer. If you don’t particularly fancy shelling out some of the high prices that both Dewalt and Bosch are selling their products for, looking into the range offered by Ryobi might save you a serious amount of cash.
Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.

With a three-horsepower motor inside, this SawStop ICS31230-36 3HP 230V 60Hz Cabinet Saw Assembly with 36-Inch Industrial T-Glide Fence System is suitable most of the jobs you have in mind. Its industrial T-Glide fence system lets you make all the cuts you need, and the extension table gives you more room to work too. It also features a system that locks the wood in place to ensure that you make the accurate and completely straight cuts that you need.
Cabinet table saws are not portable. They’re instead designed for use by professional woodworkers. That means that they’re designed to have a lot of power and to stand up to constant daily use. They have more steel and cast iron in their bodies to increase their durability, which also means that they tend to be lower-vibration than other units, which leads to cleaner cuts.
At the same time, it’s also worth mentioning that Ryobi offer some of the most affordable products that we’ve seen from many table saw manufacturer. If you don’t particularly fancy shelling out some of the high prices that both Dewalt and Bosch are selling their products for, looking into the range offered by Ryobi might save you a serious amount of cash.
When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.
In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.
Before we get into some of the top features, we want to take a look at the design of this cabinet. As it uses an enclosed cabinet, you’ll find that the motor lasts longer because it doesn’t wear down due to constant exposure to dust. This cabinet also features convenient hand wheels on the front and sides that help you make quick adjustments before cutting or as you work.
Self-Aligning Accuracy – As well as power in your table saw, you’re also going to want it to be as accurate as possible. We can comfortably say that this table saw from Bosch achieves that formidably with its self-aligning accuracy. This basically means that the square lock rip fence aligns itself for accurate performance. If you’re going to be using your table saw regularly and know that you need to get the job done correctly, this will provide it.
“The SPT99 table saw can accommodate dado cutting up to 13/16″ wide in a single pass. WARNING -To reduce the risk of injury, always disconnect plug from power source before changing blades. WARNING – To reduce the risk of injury, always use the Skilsaw SPTA70WT-DD 1/2 inch Dado Blade Table Insert or the Skilsaw SPT00A 13/16 inch Dado Blade Table Insert (both include dado accessory washer). Never make dado cuts without this insert. Do not use dado sets larger than 8″ diameter.”

Higher-End Models: The higher-end table saws ranged in price but were somewher between $ 500 - $800. These had a built-in "stand system", the largest table dimensions and the largest ripping capacities (both to the left and right side of the blade). The features were similar to the lower priced models though, so you are not paying for features, from what I've noticed.

In terms of the safety features that you’re going to want to look for in your table saw, one of the most prominent includes a flesh sensor. This is basically designed so that the table saw will immediately stop operating after 0.01 seconds of coming into contact with flesh. This means that if the worst should happen and you come into danger as a result of using a table saw, the damage will be kept to a minimal. As you can likely imagine, this particular safety feature will push up the price of the table saw by a small amount, but it’s definitely a feature that’s worth happening if you value your safety whilst using power tools.

Best of all though, the precision fence and locking miter gauge allow you to dial in the exact angles of bevel and compound miter cuts for complex trim and finishing work. You never have to worry about setting up multiple times for the same cut because the PM2000 is designed to let you “set and forget” while you get your multiple precision cuts made without needing to fiddle with the controls every time. While it is large and extremely heavy, this is definitely the tool of a professional woodworker that will provide performance that meets or exceeds even the most demanding tasks in your woodshop.
TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.

DeWALT DWE7480 is an excellent table saw, especially if you consider its price. It’s a step up from the highly popular DW745 and slightly more expensive, but I think the larger rip capacity and higher RPM are well worth the extra money. The DWE7480 is still in the lower price region though, and unlike the DW745 you can also get this one with a stand: the DWE7480XA!

×