Last but not least, you need to pay attention to the dust collecting capabilities of a particular model. Portable units usually have a weak dust-collecting capacity, but they aren’t foreseen for large projects. However, all other types do feature some kind of dust collecting system. The first thing you should check is the diameter of the dust port. The larger it is, the less debris you’ll have flying around. Also, check out the vacuum requirements because some models work only with super-expensive vacuums. As you can assume, the thing that’s lacking with those models is cost efficiency. However, if you don’t have budget limitations, feel free to invest in a high-end vacuum, it makes a huge difference.
What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.

Innovative Gravity Rise Sand – When it comes to the features of Bosch’s 4100-09 table saw, there’s clearly only one place to start and that’s with the Gravity Rise Stand that comes as part of the package here. This is basically a stand that can be intelligently adjusted to your liking and then wheeled away when you’re finished using the table saw. It’s a pretty innovative idea from Bosch and definitely one of the best stands that we’ve seen included with any table saw that we’ve reviewed or on the market.


The SawStop PCS31230-TGP252 Professional Table Cabinet Saw is our premium choice pick for a reason - it’s one of the best cabinet saws on the market. You’ll be able to tackle nearly anything you can think of with this impressive tool and work like you’d never be able to imagine. The saw is powered by a 13 amp motor that has a 220-volt requirement and saws through material quickly and efficiently. It’s a carpenter’s dream and was built with all of the needs of the craftsman in mind.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
When considering the type of saw you need for your projects, think about the type of work you want it to do, how much time will be used, the amount of money you want to spend and how much room you will have in your shop for it. If you are only a weekend woodworker and only work an hour or so each time you use it while doing small craft projects the cabinet saw may be a perfect option for you. However, if you own a small woodworking shop and will be working many hours every day with the saw the hybrid would probably be more suited. Before purchasing a saw for your needs, research by reading other consumer table saw reviews to give you the best options.

If you need to move your saw around, it comes with a table saw stand that you can put up and down with ease. Fashioned from aluminum pipes with wheels that can handle uneven terrain, move around site without breaking your back. As well as its user-friendly nature, the stand can be stored away vertically so it’s a real space-saver whether at home or on the jobsite.
As we already said, people tend to remove the safety elements to speed up their projects. Needless to say, it’s a huge mistake. Those things are there for a reason, and they should remain installed at all times. As soon as you mingle with the parts, you’ll jeopardize the integrity and your own safety. Even the best table saw cannot protect you enough if you mess with the parts on your own.
It’s not until you get a bunch of saws side by side in the shop that you start to see the difference between a $300 saw and a $500 saw. While the motors are all 15-amp, the more expensive saws have features like soft start to prolong motor and gear life, electronic feedback to maintain blade speed and gearing to maximize torque. If you look under the saws, you’ll see that the more expensive saws also have much beefier motor carriages and better-quality blade-adjusting mechanisms.

IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:
Table saw flesh sensors are a brilliant and clever piece of engineering. Sawstop revolutionised the industry when they came up with this technology. Human skin is a good conductor of electricity where is wood isn’t. So, the system works by passing an electric current through the table saw blade its self and when it’s cutting wood it’s fine as there is no conductivity between the wood and the blade but as soon as it hits human skin and becomes conductive it triggers an electric brake that stops in the blade in only 0.02 seconds. You may end up with a small cut but at least you won’t lose your finger or worse. There are quite a few different versions now on the market so we would advise you to read plenty of table saw reviews and do you research into the different systems to find the best one for you.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
Stands are one of those features where the ends really do justify the means. Some made us wish the manual writers would take a cue from Lego—just make the *@#$! things easy enough for a 7 year old to understand. That aside, SawStop set itself aside brilliantly, taking just 10 minutes to setup. All we had to do was install the wheels and two handles. Even the packaging is designed to make the process easier and the instructions were super-easy to understand. Makita was nearly as simple only requiring us to install the handle and bolt the saw to the stand.
Hybrid saws will often match in terms of power but very rarely have the stability and durability of a cabinet saw, so often they work well in a home work shop where you can add extra stands etc to help. One thing to think about though is that because they won’t be as stable this can often compromise on the quality of the cuts, this is something you must think about when deciding. Read More
One of my favorite features is the folding fence which essentially increases the surface area of the table to be able to handle larger projects. For instance, I ripped full size 4ft x 8ft sheets of plywood for a home remodel project and the Rockwell Table Saw performed flawlessly. I couldn’t have completed that particular project without the foldable fence extensions.
The bench table saw is the least expensive of the four types of saws. Some models come with a folding stand that is on wheels which makes it very easy to move or reposition without having to lift it all the time. Even though it is relatively light, constant lifting can become tiresome. You can mount these on your workbench which will give it more stability and could possibly reduce the amount of vibration as well. These smaller table saws generally have a 1 hp motor or even smaller and can run on a normal household circuit with no issues.
The Powermatic 1792001K PM2000 is an award winning cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. The 1792001K PM2000 is the result of years of work and research and hundreds of interviews with woodworkers that offered input which was eventually implemented in the saw. The performance, reliably and safety of this saw are so great, that they actually set a new standard by which all other cabinet saws are judged.
The cabinet saw available on the market today is the SawStop ICS51230-52 5 HP 230V 60 Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System, which comes with the longest fence system that you’ll find. Not only is that system easy to use, but it allows you to make different types of cuts and change the orientation or angle of the wood to the blade.
In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.

If we were going to choose one saw above all the others for our own woodworking shop, we would choose the Grizzly G0690. It’s got a relatively small footprint, it’s built like a tank, and its provides exceptional stability and vibration dampening. For a cabinet table saw in its class, you just can’t beat the value or performance that the Grizzly G0690 provides. Definitely check one out when you start shopping for your cabinet table saw, as it does not disappoint.
I see the ovens next to 'fridge. Isn't that a no-no? The heat from the ovens make the 'fridge run to cool more when the ovens are used, upping the electric bill. They are also too far from the center of preparation. I would have put them against the long counter. It would also allow counter space by the fridge to place items when putting them in or taking them out of the 'fridge.
×