If you need a table saw that can travel, the Bosch 4100-09 consistently earns high marks. Reviewers praise its power, accuracy, easy setup, and easy blade changes. They also love the gravity-rise wheeled stand, which rolls smoothly and snaps open or folds flat in a single lever-activated motion. Finally, they appreciate the convenience of the blade guard system, complete with riving knife and anti-kickback pawls.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
That being said, because of their portability, you’ll find that this type of table saw tends to be less powerful than other more permanent saws. This is because they have less power and less noise muffling too, so you’ll find them to be louder. What’s more, because of that aforementioned lack of power, you might find that you’re unable to use the law to cut through certain materials. This shouldn’t put you entirely off a portable table saw though. For many users, they offer the best of both worlds and provide the complete sawing experience that they need from their table saw. Portable Table Saws
It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
There are a lot of great table saws on the market, but we’d have to say the best is the DEWALT DW745 Compact Jobsite Table Saw. This design enables you to be flexible with where you set up shop as well as extremely efficient thanks to the innovative technology that was incorporated into the design. Additionally, it has a 15 amp motor and a 20-inch rip capacity that makes it more than capable of taking on any challenge you throw at it.
Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.
When it comes to the type of wood that you can cut through with a cabinet table saw, you can purchase one in confidence of the fact that you’ll be able to cut just about any type of wood. That being said, as a general rule, you’ll find that the more expensive cabinet table saws offer great strength and flexibility. However, in terms of the pricing of table saws, you’ll definitely find that they can become pretty expensive. This is no surprise though really, especially when you take into consideration the fact that cabinet table saws are designed solely to be used within a professional environment.
Although it is one of the cheaper circular saws available for sale, this model by Craftsman tends to be a really good deal for most woodworkers. First of all, it is a portable model that comes with a wheeled stand. This is great because it gives you the power to use it whenever and wherever you need it. Second of all, it comes with a foldable design, so you shouldn’t have to worry about whether there is enough space to store it or not. At 57 pounds, it is fairly easy to transport. The saw is powered by a powerful 15.0 amp motor that delivers an arbor speed of 5000 rpm for accurate rip cuts. It comes with a blade diameter of 10-inch and a blade shroud with 2-1/2″ port. In terms of cutting results, this model is very appreciated by any craftsman, especially by DIY workers. Besides that, it is a very durable and strong machine that comes with a die cast aluminum construction. Furthermore, on the right side, you will discover an extension table that will maximize the working space. Due to the fact that you will have plenty of space, you can now complete any kind of projects.
It’s a little extra assembly work, but you’ll be grateful you did it later. The blade guard will keep your hands away from the saw and the splitter will help to reduce kickback from the machine and keep the wood flowing smoothly through the table saw. Additionally, if you’re working to cut thin boards, you should use a push stick or a push shoe to make sure your hands stay guarded while you work.

Cabinet table saws are not portable. They’re instead designed for use by professional woodworkers. That means that they’re designed to have a lot of power and to stand up to constant daily use. They have more steel and cast iron in their bodies to increase their durability, which also means that they tend to be lower-vibration than other units, which leads to cleaner cuts.
The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.
Measuring in at 19.9" x 23.4" x 13.4", the SPT70WT-01 is compact enough to fit into any aspiring handyman’s garage, but powerful enough to tackle anything you throw at it on the job site, meaning it’s an ideal entry-level table saw for the amateur hoping to turn his hobby into a career. Sturdiness, durability, and anti-kickback technology make the world’s first worm drive table saw a revolutionary machine. Satisfied buyers can’t get enough of this balanced wood-devouring behemoth.

Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.

The first measurements we looked at with the performance testing was blade speed cutting all three of the test materials. This tests gives us a relative comparison of how much blade speed reduction the motors have under different loading conditions. In our opinion this gives us an idea of how strong the motor/gear box combination is for each saw. For each test we also recorded the “no-load” speed to capture the relative drop in rpm in the blade speed while cutting wood. We used our as-measured no-load speeds instead of the published values from the manufacturers.

Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.
With a riving knife that has a quick release design that makes it easier to change, it’s no wonder that this Powermatic 1792017K Model PM2000 10-Inch 5 HP 1-Phase Table Saw with 50-Inch Accu-Fence and Workbench is so popular with shoppers. That knife also has built-in kickback prevention that will keep your hands safe and help you focus on your work. Though it’s just as sturdy as other cabinet saws, this one comes with a caster system that allows you to move the saw across your shop.

How big a table saw is, is determined by the largest blade the saw will hold. 8” blades are the smallest that should be used for any home workshop. You can get blades in 9”, 10”, and 12” sizes as well. Most workshops will not really need the 12” blade as this has a very deep cut capability, but for construction firms and larger, commercial shops, the 12” comes in handy.
Large Cutting Capacity – When you’re working as a professional, it goes without saying that you’re generally going to need to cut a number of different sizes of wood. From look at this product, it’s pretty clear that DEWALT definitely understand this. The table saw features a 32.5 rip capacity, which is designed to easily cut through a variety of different shelving and trim materials, whether they be large or small. It might not be the case that you instantly need the ability to cut larger materials, but it definitely couldn’t hurt to have the option.
Great job with this testing. As far as the Hitachi. Many sources online point to minimal startups of the Hitachi c10rj before becoming unusable (not starting). The soft start module apparently doesn’t hold up. If it happens in 30 days it can go back to the store but after 30 days you call Hitachi (most described as unpleasant) drive to your closet Hitachi Service center and wait (up to months). I really like the Hitachi myself but am afraid of the soft start module error. THANKS FOR ALL THE GREAT WORK AND CONTENT. Please forgive any punctuation etc. This is tough on phone.
I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!
I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.
×