Table saws can be tougher to evaluate on paper since they don’t include torque measurements. Each of the table saws we tested have 15 amp motors, but vary widely on no load speed. The ones with lower RPM values are bleeding off speed in exchange for torque. While the right balance is always tough to achieve (and is a moving target with every new motor development), here’s where each saw prioritizes speed.
Love the video. It was very helpful, answered some of the questions I've had and wondered if you can expand this a bit further. I have a Thomasville bedroom set that I bought in 1981. After all of the years of my wife using hairspray, there's a layer of it on the bed's foot board and the top and leading edge of the dresser. Will this technique remove the hair spray and restore the finish? I tried using denatured alcohol to clean it in the past but stopped short of using a sanding pad or working it to the point that nit was anything but tacky. Sounds like I didn't work it long enough. Am I right or do I need to do something else? These areas are the only bad spots on any of the 5 pieces of the set. Thanks!

Whether you are a professional contractor who does a lot of work clients, or you just love working with wood, your workshop really needs a cabinet saw. Unlike job site and hybrid saws that are portable, these saws are much heavier and designed use in one location. Cabinet saws come with features like a dust collection port, accident prevention and safety features and fencing systems.


The quiet, 220-volt motors in these saws cut through the hardest stock, hour after hour, without bogging down. Cabinets are metal and extend to the floor for the best dust collection. The tops are cast iron, wide, and stable, which makes it easy to cut sheet goods. The trunnions are cabinet-mounted, so you get minimal vibration and maximum accuracy. They're also heavy; some weigh over 600 pounds. Once a cabinet saw's in place, that's where it stays.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
Safety is at a pretty high level, to say the least. There are a few integrated mechanisms that prevent accidents from happening, but that doesn’t mean you shouldn’t handle it with care. Also, don’t forget to wear safety equipment at all times. Whether you’re a professional or a beginner, you’ll definitely like this particular model due to its versatility and a wide array of potential.
Accessories 10″ 24-Tooth Carbide Blade, 2x Blade Wrenches, rolling stand, blade guard assembly, push stick, miter gauge, rip fence 10 in. 40-tooth carbide-tipped blade, throat plate insert, smart guard system, rip fence, miter gauge, push stick 32T carbide-tipped blade, rip fence, miter gauge, push stick, and wrenches Rip Fence, Miter Gauge, Smart Guard System, Push Stick, Blade Change Wrenches 24-tooth SKILSAW Carbide-tipped blade for ripping, miter gauge, self-aligning fence, guard system including anti-kick back device, insert plate, push stick and wrench

Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. The Makita was given the best score of 1 as it was considerably quieter than the remaining. DEWALT and Delta were ranked worse with a score of 3, while the remaining were ranked as a 2.
Though you’ll still want to wear safety gear when using this table saw, it has safety features that will keep you safe too. One of those features is an emergency stop. One touch of the bright green power button brings the motor to life, but when you lift up on the emergency stop that surrounds the power button, you can stop the motor in its tracks. This button has a convenient design that lets you hit and lift it with your leg or knee too.
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.
Deciding on what portable saw to get is not an easy task. There is so much out there on the market and such a wide combination of options. You can use our top 5 picks to get a taste of what’s out there and maybe find your perfect portable power saw right off the bat. However, we feel that you should also be equipped with the knowledge to go out and make your own decisions on portable table saws. We are going to run through the most important factors and features to consider before you make your purchase. These are factors that have a direct impact on performance.
Skilsaw SPT70WT-22 is a portable 10 in. Worm Drive table saw designed for ripping and is the first of its kind to hit the market. This Skilsaw has a powerful Dual-Field 15 amp motor that is powerful enough to handle even the toughest jobs. The motor has a smooth startup and runs cooler, so it lasts longer. With a small, compact size, easy to transport size, this portable saw has a lot to bring to the table. Skilsaw’s SPT99-12 is also this same table saw but also includes a rolling stand which allows you to easily transport and move this saw around the job site.
Table saws can be tougher to evaluate on paper since they don’t include torque measurements. Each of the table saws we tested have 15 amp motors, but vary widely on no load speed. The ones with lower RPM values are bleeding off speed in exchange for torque. While the right balance is always tough to achieve (and is a moving target with every new motor development), here’s where each saw prioritizes speed.
Different types of table saw rely on different motors. With the smaller and more portable saws, 120V direct drive motors can deliver up to 2HP. This is more than enough power if you’re working with less substantial sheets of material. The larger saws have belt drive motors running on 240V. These produce 3-5HP. Think carefully about the materials you’ll be working with. Get the right sized motor for your cutting needs.
For some table saws, a dust collection system is just a bag that collects the dust generated from your table saw. This might do the job perfectly well for many novice table saw users, whilst others might benefit from a more sophisticated dust collection system. Either way, it’s of paramount importance to make sure that you pick up any dust generated by your table saw, as it could be dangerous in the long term to both you and your family.
Though you’ll still want to wear safety gear when using this table saw, it has safety features that will keep you safe too. One of those features is an emergency stop. One touch of the bright green power button brings the motor to life, but when you lift up on the emergency stop that surrounds the power button, you can stop the motor in its tracks. This button has a convenient design that lets you hit and lift it with your leg or knee too.
The DEWALT DWE7490x 10 Inch Table Saw is an excellent tool for anyone, whether they need it for carpentry work or DIY projects. You’ll be able to complete your tasks with ease thanks to the superb technology and easy transportation. The device comes with powerful 15 amp motor and has impressive maximum depth capabilities. You’ll also be pleased with the 2 inch dust storage port that has a vacuum connection.
No matter what you need a table saw for, the three listed above are great choices to consider when you’re doing your shopping around. Whether you’re a professional contractor or a serious DIYer, any one of them will have all the features, power, and portability that you could want in a table saw. All of the ones listed here, and most others have warranties and 30-60 day money back guarantees to give you a chance to see if you like them so your purchase won’t be a waste if you don’t, you will be able to get your money back, but we’re pretty sure that if you choose one of the three that we have detailed for you, you’re going to be able to join the many, many customers who are very happy with their purchases.
The SKILSAW SPT70WT-01 is one of the most efficient circulars saw on the market. It has everything you need. It is quality, durable and has a great price. It comes with a 15 amp dual-field motor that delivers 5300 rpm and 25 inches rip cutting capacity on the table top. The maximum depth of cut at 90 degrees is 3-1/2 inches while at 45 degrees is 2-1/4 inches. The SPT70WT-01 measures 19.9 x 23.4 x 13.4 inches and weighs 49 lbs.. It is a lightweight unit that comes with a compact design. Its lightweight feature makes it portable and easy to transport from a place to another. Thanks to its 10 in. 24 tooth carbide rip cutting blade, this SKILSAW model has the ability to rip any type of wood. As compared to other similar units, this one comes with a plethora of useful accessories, such as rip fence, table insert, barrier guard assembly, miter gauge, push stick, anti-kickback device, blade wrench, hex wrench and manual.
It is extremely lightweight so that it can be easily moved around. The best feature for me is the unique capability to capture dust both below and above the blade. That keeps your workplace clean, and you save time. The safety features and ease of use further add to the convenience element. Additionally, the product comes with a 3-year warranty, which is quite good for a tool in this class.
Hybrid saws will often match in terms of power but very rarely have the stability and durability of a cabinet saw, so often they work well in a home work shop where you can add extra stands etc to help. One thing to think about though is that because they won’t be as stable this can often compromise on the quality of the cuts, this is something you must think about when deciding. Read More
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
It is able to protect carpenters and DIY workers by helping to detect the electrical current inside of each person that accidentally comes into contact with the saw blade. Once they’ve been detected, the saw automatically shuts off within milliseconds, keeping workers safe from devastating and life altering injuries. The SawStop SNS175-TGP36 HP Saw is one of the best tools you could choose to invest in - we highly recommend it.

We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
Craftsman 10 table saw Craftsman Radial Arm saw 10Craftsman 16 direct drive scroll saw Chicago Electric 10 compound Slide Miter saw Wagner power painterBlack and Decker rotary saw and jig sawCraftsman corded drill. Craftsman 10 compound miter saw.Cleaning out my shed and am trying to downsize. $550 or best offer and its all yours. Ill help load but wont deliver. Great Christmas gift for that ha...
The Delta 36-L552 is a professional grade table saw, built for highly demanding use. You can use it all day everyday and it won’t miss a beat. It’s extremely accurate and will always produce the straightest cuts possible. Because of the high price we would always recommend you really spend some time looking into reviews etc to make sure it’s definitely the right product for you.
For ideal usage, the on/off switch needs to be mounted on the front of the saw and should be easy to turn off with your knee or a swat without having to look at it to locate it. Most table saw models have a safety feature that is a plastic key that has to be inserted before the table saw can be turned on. Some may even have a way to padlock the switch.

One shouldn’t expect a massive amount of storage, but being a table, it does offer some level of free space. In fact, some models even offer space for fences, gauges, blades, and other necessary equipment. Apart from that, you can always keep the necessary tools in the reach of your hands. It will make the process much easier and also a lot quicker.
Once you’ve made sure that the table saw is unplugged and there aren’t any extra materials in your workspace, you should turn your attention to the miter slot. See also related: Top 10 Miter Saws here. You’ll want to make sure that the miter (click here for sliding miter saws) slot is parallel to the blade. It is important that all measurements are precise and exact – nothing short of parallel will do. Once you’ve measured the blade and the miter slot, you’ll need to check the fencing as well.

Last but not least, you need to pay attention to the dust collecting capabilities of a particular model. Portable units usually have a weak dust-collecting capacity, but they aren’t foreseen for large projects. However, all other types do feature some kind of dust collecting system. The first thing you should check is the diameter of the dust port. The larger it is, the less debris you’ll have flying around. Also, check out the vacuum requirements because some models work only with super-expensive vacuums. As you can assume, the thing that’s lacking with those models is cost efficiency. However, if you don’t have budget limitations, feel free to invest in a high-end vacuum, it makes a huge difference.

A splitter is a piece of metal that keeps the blade from binding in whatever material you are cutting if the saw kerf starts to close up. The splitter is vertical and sits directly behind the blade. This plays a big part in preventing kickback and should be mounted on the motor assembly so it rises and falls with the saw blades movements. You can also get splitters that can be adjusted to fit the width of the kerf.
The Craftsman table saw is one of the most compact of the bunch when it’s folded up. And if you can get it for the sale price of $260, it’s also the cheapest of the best table saw options. The blade guard and anti-kickback pawls are identical to the Porter-Cable and are the hardest of any of the saws to install. And they are the only two blade guards that don’t have a feature to hold them out of the way when you’re adjusting the blade or setting up the cut.

Is your blade angle taken care of! Good – that means you’re almost done with your safety check process. Now you need to check the material you’re working with. You can’t just pick up any random piece of wood and expect it to fit properly. You’ll have to use wood that is flat and straight. Wood that is curved or that is slightly bowed or cupped will cause issues for you when you try to cut it down – if you need to work with this sort of material you’ll need to find another cutting tool, like the reciprocating saw (click here for full guide).
If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  
The first measurements we looked at with the performance testing was blade speed cutting all three of the test materials. This tests gives us a relative comparison of how much blade speed reduction the motors have under different loading conditions. In our opinion this gives us an idea of how strong the motor/gear box combination is for each saw. For each test we also recorded the “no-load” speed to capture the relative drop in rpm in the blade speed while cutting wood. We used our as-measured no-load speeds instead of the published values from the manufacturers.
These models tend to be much heavier than portable models, clocking in at 200+ pounds in many circumstances, which mean you may need another person in order to move them safely. The big upside to this model is that that additional weight goes to good use. They tend to have much larger rip capacities, and the table top tends to be more durable and stable than the expanding systems used in portable models.

In terms of size, the table height from floor measures thirty four inches, with extension it measures twenty seven by forty inches and overall dimensions are 62 by 41 by 40 inches (LWH). This is simply an amazing saw and not only will you use it for many years to come, but it’s going to help you get the professional results you’re looking for in any project.


Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.

If you need a table saw that can travel, the Bosch 4100-09 consistently earns high marks. Reviewers praise its power, accuracy, easy setup, and easy blade changes. They also love the gravity-rise wheeled stand, which rolls smoothly and snaps open or folds flat in a single lever-activated motion. Finally, they appreciate the convenience of the blade guard system, complete with riving knife and anti-kickback pawls.
On the other end of the handyman spectrum, you’ve got the seasoned professional with years of experience under his belt. We all know the type: he’s the guy that expects only the best, and DEWALT more than delivers with their patented DWE7491RS. This wood-slicing machine is the cream of the crop when it comes to cutting through even the toughest materials. The DWE7491RS measures 26¼" x 22", so it’s a relatively large apparatus — you’re going to want to make sure that you have plenty of space in your garage for this table saw.
Additionally, you’ll be able to enjoy the dust collection port system on the cabinet. It leads its industry in its ability to efficiently gather up to 99% off all dust put off by the device both above and below the table. The SawStop PCS31230-TGP252 Professional Cabinet Table Saw is a powerful and invaluable device - definitely one of the best investment choices you could make.
A table saw can be classified in many ways, and I’ve come across terms like contractor, folding, featherboard, hobby, induction, sliding and zero clearance. However, I will conform to the most basic and clear classification and range the tables accordingly. That means I’ll order them by benchtop table saws, jobsite table saws, cabinet saws and hybrid table saws.
×