3,650 Rotations Per Minute – As you’ll find above in this page, portable table saws tend to be a little less powerful than well, their less portable counterparts. However, the 3,650 rotations per minute offered by this 10-inch table saw allow for both high precision and incredibly powerful cutting. Plus, with a rotations per minute of 3,650, you’ll find the product to be considerably faster at cutting just about anything. If you care about how portable your table saw is, but don’t fancy compromising on speed and power, you wouldn’t be mistaken for thinking that the Bosch 4100-09 truly has it all.
Patrick – Thanks for the feedback. Trust me, I wish we could spend more time on every aspect but we spent hundreds of hours as it was. I can tell you that the rack and pinion fences are much better than the standard fences of the past. Our entire group felt strongly that we’d prefer the rack and pinion on all the saws. We felt the Ridgid and Delta fences were the least impressive of the standard type.
The first measurements we looked at with the performance testing was blade speed cutting all three of the test materials. This tests gives us a relative comparison of how much blade speed reduction the motors have under different loading conditions. In our opinion this gives us an idea of how strong the motor/gear box combination is for each saw. For each test we also recorded the “no-load” speed to capture the relative drop in rpm in the blade speed while cutting wood. We used our as-measured no-load speeds instead of the published values from the manufacturers.
New, unopened in boxTraditional guard and riving knife system allows unlimited capacity for cross and rip cutsLightweight and compact design makes it easy to carry anywhere and sets up in seconds to cut wood, tile, plastic, metal, and aluminum Adjustable Miter Gauge for 0to 60angled cuts, right or leftSafety switch with key prevents accidental startAccessories included 1-miter gauge, 1-rip fenc...
One of our favorite features of the device however, would have to be the load speed and maximum cutting depths. The DEWALT DWE7480 Compact Job-Site Table Saw can reach a load speed of 34,800 rpm and can reach a maximum cutting depth of 3 ⅛ inches when working at a 90 degree angle and 2 ¼ inches when working at a 45 degree angle. You’ll love the quick and accurate cuts you’ll be able to make while using this device - it will revolutionize the way you’re able to go about your job.
I do not which is the best table saw, but I can tell you which is the worst. The rigid portable saw is a piece of garbage. I have purchased two in the last 4 years and the motor has failed in both, only to find that they do not sell a replacement motor. The Rigid customer service will not respond to any questions associated with the saw or replacement parts. I will not buy another Rigid tool and currently planning to try the Bosch table saw.
Once you’ve gathered your materials, turn your attention to the plate in the middle of the table saw. It surrounds the blade and should have two screws that hold it in place (however some models will have four). Use your screwdriver to undo these screws and set them aside. Then take the plate off and set it to the side as well. Then check to make sure the blade is at its full height by going to the back of your table saw and winding the blade up to full height.
Ease Of Use: The convenience or ease of use is another key factor to take into account when deciding on the best portable table saw. You have to understand that this device should be something that can be carried easily, fixed simply and used efficiently as and when you need to. Maneuverability is a fundamental element in this matter as well. From setting it up to fixing the wood in place, you have to make sure that the table saw that you buy is convenient and simple to use in all situations and locations. The only caveat to this is if you have one fixed location in mind for 90% of your work or more.
Dewalt designed an excellent table saw when they created the DW745 and we consider it to be the best buy on the market from our review. The design is fairly lightweight and easy to transport as it only weighs about 45 pounds. Additionally, the device is full of great features that enable it to work with speed and efficiency that you typically don’t see in a portable saw.
The other kind of portable table saw is the wheeled/folding leg variety. The wheeled models come with wheels that can be used to roll them for place to place. The folding leg variety may or may not have wheels. Both models feature a mechanism by which they can be raised up and used without a table. This is what sets them apart from benchtop models.
First up is the portable table saw. There are two variations in this category, the first of which is the benchtop. As the name implies, the benchtop table saw is designed to be used on top of a table or bench. They’re small, so that it doesn’t matter which table or bench you put them on, and they’re light enough to be carried from place-to-place. This type of saw was originally meant for construction, but that doesn’t mean that you can’t get good use out of it in your shop or garage.
Safety Features: All said and done, you have to accept that the portable table saws are amongst the more dangerous tools to operate. If you are not careful, you can easily get hurt. This makes the safety features some of the most important to consider. I would keep an eye out for features like anti-kickback pawls and blade tilt as they go a long way in avoiding accidents. Most also come with a magnetic switch that makes sure that the machine does not get started on its own accidentally. This is essential. Do not buy a portable table saw without a magnetic switch.

Large Cutting Capacity – When you’re working as a professional, it goes without saying that you’re generally going to need to cut a number of different sizes of wood. From look at this product, it’s pretty clear that DEWALT definitely understand this. The table saw features a 32.5 rip capacity, which is designed to easily cut through a variety of different shelving and trim materials, whether they be large or small. It might not be the case that you instantly need the ability to cut larger materials, but it definitely couldn’t hurt to have the option.

Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.


The DeWalt, Bosch and Ridgid saws have strong stands that are easier to set up, sturdy fences that lock down parallel to the blade every time, and smooth-operating blade controls. If you’re a contractor or an avid DIYer who just likes top-quality tools that feel good and last a long time, we think the extra few hundred dollars is a good investment.
Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.
The Powermatic 1792001K PM2000 is an award winning cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. The 1792001K PM2000 is the result of years of work and research and hundreds of interviews with woodworkers that offered input which was eventually implemented in the saw. The performance, reliably and safety of this saw are so great, that they actually set a new standard by which all other cabinet saws are judged.

Love the video. It was very helpful, answered some of the questions I've had and wondered if you can expand this a bit further. I have a Thomasville bedroom set that I bought in 1981. After all of the years of my wife using hairspray, there's a layer of it on the bed's foot board and the top and leading edge of the dresser. Will this technique remove the hair spray and restore the finish? I tried using denatured alcohol to clean it in the past but stopped short of using a sanding pad or working it to the point that nit was anything but tacky. Sounds like I didn't work it long enough. Am I right or do I need to do something else? These areas are the only bad spots on any of the 5 pieces of the set. Thanks!
×