When it comes to power tools, table saws provide convenience when tackling DIY jobs or larger commercial tasks. With their table surface, you are able to get more accurate cuts with the materials you are working with. Utilizing the miter gauge, you will find these power tools to provide the same accuracy as your favorite circular saws without the hassles.
Lack of mobility is the cabinet saws major drawback. Some cabinet saws need proper electrical wiring set up and often weigh a huge amount because of cast iron table tops and full cabinet like stands. But if your setting up a new wood shop or have a work space or wood shop of your own then there is no better investment you can make other than purchasing a cabinet table saw.
One of my favorite features is the folding fence which essentially increases the surface area of the table to be able to handle larger projects. For instance, I ripped full size 4ft x 8ft sheets of plywood for a home remodel project and the Rockwell Table Saw performed flawlessly. I couldn’t have completed that particular project without the foldable fence extensions.
All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
Different types of table saw rely on different motors. With the smaller and more portable saws, 120V direct drive motors can deliver up to 2HP. This is more than enough power if you’re working with less substantial sheets of material. The larger saws have belt drive motors running on 240V. These produce 3-5HP. Think carefully about the materials you’ll be working with. Get the right sized motor for your cutting needs.
Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
Probably one of the things that users will love most about this table saw is the solid granite surface which offers a seamless work area and excellent support. Another advantage of the Steel City 35955 is the fact that it comes with powerful magnets which allow swift changes without having to worry about using any type of tools. Since there’s a built-in mobile stand, you can easily position the saw around your shop without requiring the help of a second person.
There’s a lot to like about this saw. The stand is easy to set up and very sturdy. We like the smooth-operating table extension and the blade guard’s hold-up feature and ease of installation. The only downside we found is that the motor mount is less rigid than those on the other saws we tested. We suspect that’s why the cut quality on our torture test was not as good with this saw.

The SKILSAW SPT70WT-01 is one of the most efficient circulars saw on the market. It has everything you need. It is quality, durable and has a great price. It comes with a 15 amp dual-field motor that delivers 5300 rpm and 25 inches rip cutting capacity on the table top. The maximum depth of cut at 90 degrees is 3-1/2 inches while at 45 degrees is 2-1/4 inches. The SPT70WT-01 measures 19.9 x 23.4 x 13.4 inches and weighs 49 lbs.. It is a lightweight unit that comes with a compact design. Its lightweight feature makes it portable and easy to transport from a place to another. Thanks to its 10 in. 24 tooth carbide rip cutting blade, this SKILSAW model has the ability to rip any type of wood. As compared to other similar units, this one comes with a plethora of useful accessories, such as rip fence, table insert, barrier guard assembly, miter gauge, push stick, anti-kickback device, blade wrench, hex wrench and manual.

In addition to its cutting versatility, the PM1000 also features a blade surround and collection hose for dust extraction. This method of collecting dust while the saw is in operation improves both blade visibility and air quality in the shop. Best of all, the 50-inch fence provides exceptional control when ripping lengthy sections of wood, and the extended geometry of the table allows for easier manipulation of longer workpieces.
Contractors who do a lot of finishing work and interior/exterior trim work know the value of a good portable table saw. DeWalt has built the DWE7490X from the ground up as a stable and safe job site cabinet saw that can be used to make those precision cuts quickly and easily without the need to pre-fabricate materials and then bring them to the job site for final fitting.
Lack of mobility is the cabinet saws major drawback. Some cabinet saws need proper electrical wiring set up and often weigh a huge amount because of cast iron table tops and full cabinet like stands. But if your setting up a new wood shop or have a work space or wood shop of your own then there is no better investment you can make other than purchasing a cabinet table saw.
I see the ovens next to 'fridge. Isn't that a no-no? The heat from the ovens make the 'fridge run to cool more when the ovens are used, upping the electric bill. They are also too far from the center of preparation. I would have put them against the long counter. It would also allow counter space by the fridge to place items when putting them in or taking them out of the 'fridge.
15 Amp Motor – You’ve likely noticed that the power of motor used by DEWALT in their table saws sits at a pretty consistent 15 amp. That’s no surprise though really, when you take into consideration exactly what a 15 amp motor is able to achieve. In all, we’d say that it provides pretty much as much power you’re going to need. What’s more, this power coupled with high precision allows the table saw to easily rip through just about any hardwood. You’d struggle to find a table saw that pumps out quite as much power.
These tests and evaluations are very difficult, take a lot of time, and ultimately limited in scope as we’re not a professional testing company and we’ve got limited time to evaluate the tools. We cannot do longer term testing that would shed light on durability and we can’t possibly test every application that you might use of one of these saws for. However, we feel comfortable that all the table saws in this Head-to-Head are good saws and our testing helps bring to light pros and cons for each saw.
The final brand that’s definitely worth a mention when it comes to evaluating the brands we’ll be featuring in our table saw reviews is Ryobi. They’re largely known for manufacturing components for use in the automobile, electronics and telecommunications industry. However, they’ve more recently branched out into their own range of power tools and other hardware related tools, including table saws. With that taken into consideration, from our experience of Ryobi’s products, we’d definitely say that they’re a brand well worth keeping your eye on.

And finally, there are a couple of jobsite table saws running around with flesh detection to drop the blade out of the way if it detects a strike. There’s a significant premium in cost for these saws and there has also been plenty of litigation regarding whether it should be required on every table saw and whether more than one company has the right to manufacturer the mechanism. But they’ll save you a much worse injury in the event of an accident.
No matter what you need a table saw for, the three listed above are great choices to consider when you’re doing your shopping around. Whether you’re a professional contractor or a serious DIYer, any one of them will have all the features, power, and portability that you could want in a table saw. All of the ones listed here, and most others have warranties and 30-60 day money back guarantees to give you a chance to see if you like them so your purchase won’t be a waste if you don’t, you will be able to get your money back, but we’re pretty sure that if you choose one of the three that we have detailed for you, you’re going to be able to join the many, many customers who are very happy with their purchases.

Lack of mobility is the cabinet saws major drawback. Some cabinet saws need proper electrical wiring set up and often weigh a huge amount because of cast iron table tops and full cabinet like stands. But if your setting up a new wood shop or have a work space or wood shop of your own then there is no better investment you can make other than purchasing a cabinet table saw.
The final key factor that you’ll want to take into consideration when picking the right table saw is just how easy that table saw is to use. Obviously for experienced table saw users, ease of use might not be something that is so much of a big deal, but if this is going to be your first table saw, it’s definitely something that you’ll want to look out for. The last thing you want is to purchase a brand new table saw and find that you can’t use it.
Bosch 10” table saw has it all in terms of precision and accuracy. It has a riving knife system for high material controls and visibility in cutting. The blade is designed with anti-kickback pawls to ensure once you start cutting, you will get accurate results to the end. The entire unit is designed with heavy-duty material for durability. The square lock rip fence has adjustable style to guarantee continued accuracy and precision in all your work. Additionally, the table saw has an easy to transport design with additional tabletops handles for portability. You can also regulate the cutting speed of the table saw to the place you are comfortable.
Other features include two handwheels with measurements around each one that you can use to set up your cuts or as you cut and an emergency button that acts like a kill switch to pull power from the motor during an emergency. This cabinet saw comes with an easy change system changing the blade and a warranty that covers the saw two years and the motor five years.
The most critical safety feature on a table saw is the blade guard. It’s all that separates your fingers from the rapidly rotating blade. You need this to be transparent or it will make measuring awkward. The last thing you want is to be tempted to remove an unfit guard. Check closely for a clear, flexible blade guard. Safety is paramount when operating a table saw.
A table saw has two main ways it can seriously hurt you. One is obvious and that is having any part of your body come into contact with the blade. Any table saw you are seriously considering should have a blade guard installed. The clearer the better. And make sure you leave it on. The blade guard can’t do its intended job from a workbench or shelf.

Inspect your wood carefully to make sure that you are able to maintain a safe working environment and are able to complete high quality work. Now that you’ve got these things in mind there are only a few more things you’ll need to remember before you’re ready to get to work! First, remember that the blade spins towards you, the operator. This means that you’ll always want to feed the wood to the machine by pushing it towards the blade and away from you.
It is an extremely durable and sturdy product. However, there are some drawbacks. First of all, it is expensive without quite backing up that price in all areas. It does not really have the elite safety feature of our top choice, and it also lacks high-end power. These are minor points (it is still safe and powerful), but you expect it to be perfect at this price.
15 Amp Motor – If there’s one thing that you’ll learn from this website’s table saw reviews, it’s than I order to for a table saw to be effective, it needs to be pretty powerful. With an included 15 amp motor, we can quite comfortably say that this particular product meets that specification. In fact, you should find that the motor is able to easily rip through hardwoods and just about any other type of wood.
The Shop Fox W1819 also comes with a miter fence with flip stop which provides excellent workpiece support and is great for longer workpieces. As for the flip stop, it’s going to be very useful especially when wanting to make several cuts of the same width. If you want to cut longer workpieces, you can also flip it out of the way and then pivot it back down in order to make more cuts at the cutting width of your choice.
One of the most widely used power tools for carpenters is the table saw. For carpenters that don’t work exclusively in the shop a portable jobsite table saw is essential. For this Head-to-Head we’re focusing on corded portable 10″ jobsite table saws. We are not including cordless table saws in this test as we plan on doing another head-to-head exclusively for cordless table saws later this year as several are available now.
If you don’t get a model with a flat table, you’re not going to be satisfied with your cut quality. It’s an overgeneralization to say that all good cuts start with a perfectly-flat table on a table saw, but there’s some truth to it. Even minor warping can result in huge changes to the final piece after you’ve made the cut. Unfortunately, it’s not always a problem that can be seen by the naked eye.
Bengt – We appreciate the feedback as it always helps us get better. Having said that I think some of your concerns were evaluated and included in the results in ways that may not be entirely clear. We adjusted each saw after checking the blade/fence measurements and had no issues getting them adjusted (I may add some text to reinforce that in the article). We don’t do long term testing in this type of article as it’s simply not feasible…so making a statement about whether the saw holds those adjustments isn’t feasible. We evaluated the fences and ranked them in the ergonomics section, we even did lateral load testing on them as part of that ranking.
The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.
The DEWALT DW745 is a smaller version of the DEWALT DWE7491RS. It’s still a good saw in its own right. It comes with a 15-amp motor, just like the larger unit, though it can only handle rips of up to 20”. You’ll experience the same power and consequently, the same speed as the larger model, though you can’t cut pieces as large. This model is also meant to be moved, and while it doesn’t have wheels, it has a metal roll cage that will help it survive travel without taking any damage.

Framing work is full of rougher cuts that rarely makes use of more than one blade at a time. But occasionally you might need dados for an onsite custom build in. If that sounds like you, be sure to find out the saw’s dado stack capacity. It requires a longer arbor and you won’t be able to use your normal throat plate for it. Some manufacturers offer a dado throat plate if they have the capacity for it.
Delta 36-L336 3 HP Motor Uni-saw with 36 Delta 36-L336 3 HP Motor Uni-saw with 36 in. Biesemeyer Fence System is ideal for woodworking cabinet making and boat building. It features speedometer style scales and a 36 in. Biesemeyer fence. The 3 HP 230-Volt motor cuts hardwoods and engineered products like MDF and melamine. The riving knife enables ...  More + Product Details Close

SawStop is the only saw in the group to employ this style fence and they have the best in the group. Ridgid comes in second with a traditional front clamping fence system that has a backside contact point. Its solid construction and wide cast front clamp left us impressed. DeWalt’s came in third with an innovative effort that locks into several points based on where you need it. Rather than sliding along, it stays in place while the rack and pinion system moves it into place. It’s not perfect, but it eliminates a lot of accuracy issues that come from locking the fence out of square on some systems.

Jet has a strong reputation for providing customers with durable power tools that operate just like professional models but cost less, and that is definitely true of this 10-inch table saw that comes with a riving knife. You’ll like the basic design of this model, which has an intuitive design that allows you to set it up and start cutting faster. It features both a solid cabinet as well as an extension table that stretches out from one end.
The obvious starting point for an analysis of which saw is best suited to the needs of a given person (or company, school workshop, and so forth) is the budget at hand. Even the most affordable table saws of a quality meriting serious consideration cost more than 200 dollars; such units are small but still capable of many tasks. The top of the line table saws come with price tags topping out at well over 3,000 dollars and can handle almost any lumber you would ever need cut and then some; more often than not these mighty saws are more tool than needed, so to speak.
That being said, they provide the best cuts out of any of these machines. They’re low vibration, have the greatest power, and since they’re not being moved around, they tend to be better calibrated. They also tend to come with higher-quality fences and miter gauges, which means that you can achieve the highest degree of accuracy when making cuts on cabinet table saws.
It is able to protect carpenters and DIY workers by helping to detect the electrical current inside of each person that accidentally comes into contact with the saw blade. Once they’ve been detected, the saw automatically shuts off within milliseconds, keeping workers safe from devastating and life altering injuries. The SawStop SNS175-TGP36 HP Saw is one of the best tools you could choose to invest in - we highly recommend it.
Miter gauges are one of those accessories that you may forget about in daily use, but then desperately need if you don’t have one. They’re used with table saws in order to cut angles that aren’t 90 degrees. The best miter gauges include hard stops at 90 degrees and 45 degrees, which are the angles that you’re most often going to be cutting at. The hard stops make it easy to set the miter gauge to those angles and cut away with confidence.
The last one in our list of the top portable table saw picks is another offering from Bosch. If you are looking for a sleek and extremely portable table saw, then this is for you. It weighs merely 52 pounds and can be easily carried around anywhere that you might go. The ergonomic grip and the uniform weight distribution further enhance the portability aspect.
Dust Collection Port – Using any table saw is guaranteed to generate an awful lot of dust and anyone who suffers from asthma will know this to be a big problem. With that in mind, it’s nice to see that DEWALT have taken precautions to allow you to properly extract dust when using your table saw. This is through the product’s 2-1/2-inch dust extraction port that allows you to quickly and easily connect a vacuum for efficient dust extraction. If you’re going to be regularly using your table saw, you’ll definitely notice the advantage of having dust automatically extracted out of the environment for you.

Our biggest surprise while running the best table saw review tests was in the cutting power and the quality of cut: There wasn’t much difference among them. All these saws ripped through 3-in.-thick oak without hesitating. We tried this test with the stock blades that came on the saws. Then we repeated the test using a top-quality blade in each saw.

×