To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.

However, thanks to the innovative safety technology incorporated into the design, you’ll never have to worry about incurring severe injury. The tool is capable of sensing human touch and will shut down within milliseconds of accidental contact. You’ll be able to work in a safe and clean space with no worries if you invest in the best quality tool like the SawStop table saw.


Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. The Makita was given the best score of 1 as it was considerably quieter than the remaining. DEWALT and Delta were ranked worse with a score of 3, while the remaining were ranked as a 2.
Some craftsmen are looking for a cabinet table saw that has both a small footprint but doesn’t sacrifice performance when it comes to cutting and shaping hardwood. If you are that craftsman, then the Grizzly G0690 was built with you in mind. With a 220-volt 3 horsepower motor, this smaller scale cabinet saw is built to rip and split some serious hardwood with minimal effort.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
Once you’ve tightened the nut again, put on the plate and set both screws back into their original spots. Screw both of the screws back in and then wind your blade back down. Now, clear your work area of any miscellaneous tools and test your machine by plugging it in and hitting the start button. Once you’ve determined that the machine is working properly you can resume your woodwork again.
The DEWALT DWE7491RS is an incredible saw, but it provides portability at a great price point. The set of wheels on this model is great for moving it from jobsite-to-jobsite without too much effort. The folding legs are also superior to the support systems on other models, and they make it so that you always have a stable platform on which to work, without adding too much weight to the machine.
Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
DeWalt DWE7490X table saw is a pretty cool portable table saw. It’s a great blend of accuracy, portability, and power. Weighing only 58 lbs, this table saw might be pint-sized, but it’s not lacking power. It has an impressive 15 A motor, 28.5 in. rip capacity, 47-degree bevel capacity, and cut depth of 3-1/8 in (at 90 degrees). Not bad for a portable table saw. Other features we appreciate are its tool-free fence adjustments for convenience and its metal roll cage for extra durability. This package also includes a scissor style stand, which allows you to easily pack up this table saw and bring it with you anywhere the job takes you!
Contractor saws weigh quite a bit more than portable saws, averaging between 150 and 350 pounds, but are still somewhat portable. They have a heavier, cast-iron table top, and a motor that is usually more powerful than a jobsite saw. Even so, they’re within prices affordable for more committed hobbyists. Contractor saws can range between $800 and $2,000. They’re good for basic cutting tasks, as well as making home furniture and cabinetry work.
As you can tell, this particular type is in the middle between portable and contractor. Some people can finish their projects with bench top saws, but the ones who can’t usually opt for hybrid saws because they are cheaper than contractor ones. One cannot say they are cheap per se, but it’s a significantly smaller investment in comparison to contractor models.

Once again our team has put some serious time and effort into our Head-to-Head evaluation to bring you the most comprehensive information available. For this evaluation, we broke things into several categories including: Precision & Accuracy, Performance (power), Price, and Ergonomics. For each of these categories we’ll rank the saws and at the end we’ll name the Best Portable Jobsite Table Saw based on all the results combined.
If you are a woodworking professional, you'll want a cabinet saw in your workshop. These are the heaviest, sturdiest and most precise table saws, with powerful motors that require a 220-volt electrical outlet. Cabinet saws require a large, dedicated space because of their guide rails and large tables (often with big extension wings). Then also tend to have the best safety and dust-control features. Woodworkers with enough space (and money) usually make a cabinet saw the permanent centerpiece of their workshop, though a few cabinet saws have mobile bases. Cabinet saws cost $1,600 and up.

At a compact 45 pounds, the DEWALT DW745 Compact Jobsite Table Saw is the lightest table saw in our review. The saw's portability doesn't mean that ripping size is compromised, though. Thanks to extending fence guides, you've got 20 inches available. Depth of cut is on par with many bigger machines: at 90 degrees, it's 3 1/8 inches. At 45 degrees, it's 2 1/4 inches. Power comes from a 15-amp motor with a no-load speed of 3,850 RPM. This is ample enough for serious DIY projects and light-duty construction site work.
The cabinet saw available on the market today is the SawStop ICS51230-52 5 HP 230V 60 Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System, which comes with the longest fence system that you’ll find. Not only is that system easy to use, but it allows you to make different types of cuts and change the orientation or angle of the wood to the blade.
The 15-amp motor is outstanding, developing up to 4HP and operating at a speed of 3650RPM. This is not quite as pacey as the DeWalt but still more than respectable. The other advantage to this motor is that – for a table saw, at least – it’s pretty quiet. Noise isn’t such an issue out on the job site but if you’re woodworking at home, the quiet motor is a real boon.
Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.
Hybrid saws will often match in terms of power but very rarely have the stability and durability of a cabinet saw, so often they work well in a home work shop where you can add extra stands etc to help. One thing to think about though is that because they won’t be as stable this can often compromise on the quality of the cuts, this is something you must think about when deciding. Read More
At first glance, the Bosch 10-Inch Worksite Table Saw may seem to be nothing exceptional. However, it's powered by the best motor in its class, and it does everything well. True, the motor is a 15 amp unit like the others on our list, but it produces 4 HP where the others produce only 1.5 to 2 HP. This is a noticeable step up in a vital area! The wheeled frame is extremely helpful for moving around your shop or garage, but keep in mind that those tires aren’t heavy-duty; you have to be careful with them on a worksite littered with nails and screws.
The blades of a circular saw are usually divided based on several factors, including diameter, arbor size, speed, application, and well as number f teeth and materials used in their construction. Most tools are equipped with 10 or 12 inches blades. This is the medium size, but there are also models that come with blades as small as 5 inches or as large as one hand. Since they are able to cut various different materials, including the most solid ones, most models have carbide or carbon blades. You may also find diamond-tipped teeth blades, but they are a bit more expensive. The number of teeth is usually between 24 and 80 and you need to decide whether you want a saw with left or right tilt. The direction in which the blade tilt is very important and it can provide plenty of advantages.

I have another post for Woodsmith magazines. ShopNotes 2.00 each copyIssue 1 Premiere Issue Shop -- Built Router TableTable Saw AccessoriesTips for Accurate CrosscuttingElu Router ReviewIssue 2Wooden Joiners MalletStorage Bin SystemHand-Cut MortisesRadial Arm Saw FenceIssue 3Handy Tool Carry-AllShop-Built Cling StationPlate Joinery TechniquesAdjustable Grinding JigIssue 4Shop-Built Panel SawThi...


The continuous-read, tape measure–type scale is ingenious and easy to read, and Ridgid’s lifetime warranty covers it against breakage. The Ridgid saw has the most versatile miter gauge with holes and slots for mounting extensions and accessories. The designers have cleverly fashioned the stand to also serve as a left-side outfeed support for ripping plywood.
The advent of ever better motive power that came with 19th century developments led to ever more efficient and ever more compact power saws. The first recognizably modern table saws date to the latter decades of that century. With compact and powerful electric motors developed and refined throughout the 20th century, tables saws were widely available and were both compact enough for home use, yet powerful enough for nearly any lumber ripping task.

While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.


My son Owen and I thank you for the truly wonderful, informative and entertaining experience provided by the TOH staff, crew and trades-people at the Pro2Pro Brookline event. From Elizabeth - who welcomed us to the event, to Chris, Kevin and others who were wonderful during the orientation session (answering questions that I'm sure you have heard dozens of times before), to Charlie, Kevin, Richard, Heath (the electrician) and Thomas (the program director), you helped us Insiders to understand and appreciate the pride that you take in your work. It was refreshing. I loved the pictures and accompanying text of the event that you posted. I have to say in closing to Chris, Kevin and Thomas (in particular) you gave my son, a budding landscaper, the impetus to continue his pursuit of the trades. Kudos to you all and keep up your great work!
×