The throat plate is the removable piece surrounding the blade that sits flush with the table. Removing it gives you the ability to access the blade for removal or riving knife adjustments. The narrower the blade clearance the better for two reasons. First, it helps keep material from falling into the blade area or lodging between the blade and throat plate. Second, it gives you material support very close to the cut to help reduce tearout as the blade exits the cut.
If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  
Portable table saws are popular partly because they cost less than bigger models, making them a good choice for occasional use or as a starter saw. They're also ideal for use on jobsites or for easier storage in a small workshop. Portable table saws include benchtop models that are light enough to carry and jobsite saws that are equipped with a folding stand, which is often wheeled. The main drawback is that these saws' small tables make it difficult to cut sheets of plywood. You can add various extensions to cope with this, but that means more to transport and set up.
These tools can be classified into three types, such as the compact, bench top and job site saw. As compared to the stationary models they are smaller and more lightweight. Furthermore, the heavier materials used in their construction are seriously reduced to keep their weight down. Most units are equipped with a 15 amp 120V motor which delivers no more than 2 hp. As it was mentioned before, the size matters and it is an important factor to consider when purchasing a woodworking machine.
Table saws are very efficient tools that have proven their worth to woodworkers and DIYers alike. They enable people to cut down and craft wood much more efficiently, but there are a few things you should know about proper use of a table saw before you begin if you want to achieve the best results. The first is to use the blade guard and log splitter to make your work easier to accomplish and a more safe environment.

If you’re going to be working with a table saw, you’re going to want to make sure you take a few safety precautions before beginning your work. Sharp, heavy duty tools like a table saw must be handled properly and treated with respect in order to see the best results and maintain a safe environment. Click here to find out the best way to sharpen your blades. Before you begin your safety preparations on the table saw itself, you need to take the time to make sure you are properly dressed for your task.
The cabinet saw available on the market today is the SawStop ICS51230-52 5 HP 230V 60 Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System, which comes with the longest fence system that you’ll find. Not only is that system easy to use, but it allows you to make different types of cuts and change the orientation or angle of the wood to the blade.
The CNS175-TGP36 SawStop is a 10 in. contractor table saw with a 45-degree bevel and a rip capacity of 36.5 in. Other than that, we think this is a pretty cool table saw for a few different reasons. First, the price is about half of all other SawStop table saws, and we know money talks (actually, it yells)! Second, like all other SawStop table saws, it has the integrated flesh sensing technology, so you can be sure you’re going to keep all your digits. Also, it has some pretty impressive power; it’s powered by 15 A motor so you’ll be able to tackle whatever you need. The last of our favorite features is its portability. For being a contractor saw, it’s pretty easy to pack up and move around.
Once you’ve made sure that the table saw is unplugged and there aren’t any extra materials in your workspace, you should turn your attention to the miter slot. See also related: Top 10 Miter Saws here. You’ll want to make sure that the miter (click here for sliding miter saws) slot is parallel to the blade. It is important that all measurements are precise and exact – nothing short of parallel will do. Once you’ve measured the blade and the miter slot, you’ll need to check the fencing as well.

Paul – Good catch….I’ve updated that to say Skilsaw not SawStop…thank you! As you can imagine…all the data makes it tough to keep it all straight. I’m not even sure how you’d install that aftermarket fence on these saws. If you do I’d love to see how!! Those really look like they are made to install on cast-iron full size saws. I’d choose the DEWALT with a slight edge over the SKilsaw.
Likes: Cuts extremely well and has excellent stability. Its blade guard and riving-knife assembly are locked and unlocked by a lever located conveniently along the table's left edge. A simple, separate shark-fin riving knife can be used when the guard is too big for narrow rip cuts. We appreciate the antiglare surface on the tape ruler that measures the distance from the blade to the fence.
Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.
Lowes had a Father’s day sale, on their Kobalt table saw with a folding/rolling stand and was $180.00, with more money off because I signed up for their credit card-so I bought it. It cuts fine, the fence locks on both ends,measurements seem ok, and it unfolds and rolls away very easily-I like it so far. I’m a home owner and I use it sporadically and treat it well, it does not appear to be very robust, so as a day to day, on the job site saw, probably not a good choice. I used to have a Makita table saw, with a terrible fence, unreliable ruler markings, and difficult to use blade guide that interfered with measurements, which you needed to do every time-a terrible saw, very frustrating to use. I have a Makita miter saw and it’s great, but the idea of buying a same brand because I liked one of their other products did not work out.
Designed to be Portable – In case you hadn’t already gathered from the above section, this is a table saw from Bosch that is clearly designed to be portable. If you’re going to need a table saw that can be moved on and off of a worksite with little effort, you’ll definitely find that to be the case with the Bosch 4100-09 and it’s included Gravity Rise Stand.
The blades are the primary factor to consider when shopping for a saw as they hugely determine the performance of your table saw. The blades will only be effective if they are set at a correct depth of cut. The table saw will also perform best if only the correct blade for the cut is fitted, as a proper blade will enable you to achieve a precise and smooth cut. When purchasing a blade, go for the one with a correct setting blade. Consider the cutting depth also as this will determine its suitability for the job. You should also ensure that the table saw is equipped with splinter guard as this will help in minimizing splintering of the board’s top surface. Splinter guard also enhances accuracy because when it is lined up at the start and finish mark the saw will cut with precision. A suitable table saw should also have a 20mm arbor as this guarantees the stability of the blade and hence, safety in the workplace.

Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.
Affordable Price Point – The price of the product is something that you’ll want to carefully consider when it comes to buying a table saw. This is largely because different people have different budgets to work with. Coming in at well under $100, you can likely imagine that this table saw from Ryobi comes in at the lower end of the market and for that low price point, you are going to have to make some compromises in terms of power and speed. However, occasional hobbyists should find that this table saw still gets the job done well.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.

It has a brilliantly powerful 15 AMP motor, which can deliver 4,800 RPM of cutting power. Is is normally more than enough for most woodworkers and hobbyists. It has stowable anti-kickback pawls and and excellent riving knife and spreader for accurate cuts. This is a great entry level saw at a great price, definitely worth looking at for your next purchase or project.
The 50-inc rip fence that comes with this JET 708675PK XACTASAW Deluxe 3-Horsepower is perfect making rip cuts without worrying about your boards slipping out of the place. This fence system has a lock down feature that will actually lock the board down at the right angle and at the measurement that you choose. It comes with an arbor lock changing the blade and a poly-v drive belt system too.
Purchasing a quality model is one of the most important investments of a wood-worker. It is a necessary item that is seen in every woodcutter shop. Without this equipment, you won’t be able to complete all your projects based on the hardwood. We all agree that this is a dangerous tool. Also, after doing some research we can truly say that it causes several injuries to the user. However, it also has a lot of advantages besides this drawback. Therefore, in you are interested in finding out more about the advantages of using such a tool, take a look below.
The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.
Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.

At a compact 45 pounds, the DEWALT DW745 Compact Jobsite Table Saw is the lightest table saw in our review. The saw's portability doesn't mean that ripping size is compromised, though. Thanks to extending fence guides, you've got 20 inches available. Depth of cut is on par with many bigger machines: at 90 degrees, it's 3 1/8 inches. At 45 degrees, it's 2 1/4 inches. Power comes from a 15-amp motor with a no-load speed of 3,850 RPM. This is ample enough for serious DIY projects and light-duty construction site work.


Bosch’s 4100-10 work site table saw is a sure win. Bosch never fails to impress us, and this table saw is no exception. It’s a 10 in. saw with a 25 in (right) rip capacity and a 47 degree left bevel. This Bosch table saw is powered by a 15A motor that reaches top speeds up to 3,650 RPM. Another feature we appreciate: its constant response circuits which continuously adapt the speed under load, giving you a continuous blade speed.
​The saw does not easily detach from the stand. Sometimes it’s beneficial to set the saw up as a bench-top saw, but the DeWALT 7491RS doesn’t come with quick release levers to accomplish this easily. In this case, you would have to use a drill to remove four screws to detach it from the stand. I wouldn’t recommend doing this unless you have to because over time the screw holes will strip.

You’ll also want to be sure to check that the teeth of the blade are facing towards you since this is the direction that the wood is cut. Once you’ve made sure that the new blade is on properly you can put on the stabilizing parts and nut again. You’ll tighten the nut by putting the spanners on the same way you did before, however, this time you’ll push the spanner in your left hand away from you to tighten the nut instead of towards you.


One of the things we looked at was the ease of assembly out of the box. We had the same person assemble each of the saws and timed the assembly to see if there are any significant differences between the models. The assembly time for the saws ranged from 21 minutes to 48 minutes. While some stands required more than twice the time, we felt the assembly time was not a significant enough factor to change someone’s mind on which saw to purchase.

You’ll also find that the metal roll cage base will give you extra strength and durability to work with and the rear feet will enable you to adjust the height of the machine should you be faced with the challenge of working on an uneven surface. There’s nothing the DEWALT DW7480 Compact Job-Site Table Saw can’t handle. You’ll quickly be impressed by its ability to tackle any project you throw at it and learn to appreciate it for the great tool that it is.


Kenny Koehler An avid endurance athlete, Kenny has competed in triathlons (he's an Ironman) and various other fitness activities. Still, his passions lie with his faith, family, friends, and his love for well-designed power tools. With a background in science, you'll often find Kenny chatting up engineers at media events to get caught up on the latest tool technology.
Skilsaw SPT70WT-22 is a portable 10 in. Worm Drive table saw designed for ripping and is the first of its kind to hit the market. This Skilsaw has a powerful Dual-Field 15 amp motor that is powerful enough to handle even the toughest jobs. The motor has a smooth startup and runs cooler, so it lasts longer. With a small, compact size, easy to transport size, this portable saw has a lot to bring to the table. Skilsaw’s SPT99-12 is also this same table saw but also includes a rolling stand which allows you to easily transport and move this saw around the job site.
Goggles are yet another thing people simply don’t like wearing. However, it’s not about comfort but saving your eyesight. As you can assume, there is a lot of sawdust flying around while you’re cutting a piece of wood. In order to prevent it from flying straight into your eyes, you have to wear safety glasses. There are hundreds of models you can choose from, but make sure they are certified as safe. In simpler words, you cannot use the first ones you stumble upon, don’t be afraid to invest in high-quality safety glasses, you’ll be thankful for them.
An excellent choice both for professional woodworkers and hobbyists with a more expansive tool budget, the Shop Fox W1819 is a 10 inch table saw ideal for making clean cuts along greater lengths of material without pinching or kickback. The blade itself is covered while in operation by a clear polycarbonate blade guard that moves back as the workpiece is passed along over the blade.

For any kind of professional woodworking and large scale construction work, the cabinet table saw is the one for the job. These types of table saws are often called stationary saws. The motor is protected in a cast iron and steel cabinet that reduces noise and vibration as well. With reduced vibration comes better accuracy which is always the desired effect, especially for professionals. The motor us a powerful 3-5 hp and requires a 220-volt outlet. If you are using it in a home workshop, a special outlet may need to be installed if 220s are not already installed in your garage or shop. Measuring about 28” x 43” and weighing in at over 400 pounds, these table saws were not designed to be portable. The large work surface is ideal for cutting large pieces with ease. Cabinet saws can use a 12” blade with no problem, although a 10” blade is the most commonly used. It is the most expensive of all of the styles of table saws.
We spent a lot of time setting up and taking down the saws to see how well the stands worked and how easy it was to install and remove the blade guard and anti-kickback pawls. Then we ran a torturous ripping test with 3-in.-thick slabs of oak to find the best table saw. And finally, we used the saws for more conventional tasks like cutting plywood and ripping framing lumber as another test to determine the best table saw.
×