From flexible plywood sheets that move on their own to thick wood boards, this Jet 708677PK XACTASAW Deluxe 5HP Cabinet Saw can help you cut through all types of wood. This saw comes with a riving knife that reduces the risk of binding and kickbacks and has a quick release design to let you use it anytime you need. A left tilt trunnion makes pushing boards and sheets through easier while also giving you the stability that you might need.
In addition to its cutting versatility, the PM1000 also features a blade surround and collection hose for dust extraction. This method of collecting dust while the saw is in operation improves both blade visibility and air quality in the shop. Best of all, the 50-inch fence provides exceptional control when ripping lengthy sections of wood, and the extended geometry of the table allows for easier manipulation of longer workpieces.
All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
Great match-up and informative… however I too noticed that “No Load” RPMs varied quite a bit from chart to chart – for the same saw. We would expect some variation of 50 RPM as you had mentioned, but not 500 to 800. See that the Hitachi changed from 4400 down to 3700, Delta jumped from 3700 to 4400, Rigid from 3650 to 4350. Upon closer scrutiny… the order of “No Load” RPMs used in first chart may have been used in all subsequent charts. When the “Load” results were ordered by hi-to-low ranking, is it possible that the “No Load” data was not kept with its saw? If so, that changes the %drop results slightly for most RPM No-Load/Load,Speed charts. No too terrible. Lots of data… Good overall presentation though for use to make informed decisions. Thank you!
The DEWALT DW745 is a smaller version of the DEWALT DWE7491RS. It’s still a good saw in its own right. It comes with a 15-amp motor, just like the larger unit, though it can only handle rips of up to 20”. You’ll experience the same power and consequently, the same speed as the larger model, though you can’t cut pieces as large. This model is also meant to be moved, and while it doesn’t have wheels, it has a metal roll cage that will help it survive travel without taking any damage.
When you purchase your table saw, more than likely it will have standard 10” carbide tipped blade that is good for general purpose use. This blade is capable of cross cutting a 4 x 4. If you replace it with a 40 tooth combination blade you will improve the quality of your cuts significantly and more than likely be much happier with the blade overall. You can get specialty blades also if you are going to be cutting other materials as well.
Perfect for both hobbyists and craftsmen, the PCS31230-TGP252 from SawStop is a 3 HP cabinet saw that delivers excellent performance while featuring the company’s patented safety system to ensure maximum safety during use. The safety system is similar to that of the G0690 from Grizzly where the blade stops in milliseconds after it comes in contact with flesh. Designed and built in order to satisfy the needs of the most demanding users, the PCS31230-TGP252 features an exacting finish and feet and a superior dust collection system. For increased precision and added strength, the PCS31230-TGP252 features a fifty two inch T-Glide fence system, but also an extension table and rails.
Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.
Durable Steel Design – With this being such a portable product from Bosch, you’d be forgiven for thinking that it’s pretty flimsy when it comes to design. However, that couldn’t be further from the case with the Bosch GTS1031’s durable and unique all-steel base. This is a design that’s clearly built to take on abuse. That’s definitely peace of mind that you’ll want to have when it comes to using this table saw in a working environment. Not that you shouldn’t be careful where possible when it comes to using your new table saw.
If you’re a DIY enthusiast, you’ll definitely find something of interest. On the other hand, professionals can also find good pieces of information on this page. The models we’ve covered all work as advertised, and you can rest assured that they are of high quality. The only thing you need to do is determine how much money you want to spend and which type is the best suiting one for your requirements.
Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.
Delta 36-L352 10 in. contractor table saw is a heavy duty table saw. This big guy is no joke! Its 15 A, 3 HP motor is not only powerful but smooth. This Delta table saw also has a HUGE rip capacity of 50-52 in. and an 82 in. table, so there won’t be much this table saw can’t handle. Its integrated BIESEMEYER fence system, precision bevel gauge, and bevel dial work together to help you get highly accurate cuts down to the nearest 1/4 degree and 1/64 in. Now that’s accurate! Other notable features are its bi-level dust extraction system which helps you keep your workspace clean, large blade opening, and SURE-LOCK dual front cranks for easy access. This table saw is ideal for the pros.
If you’re going to be working with a table saw, you’re going to want to make sure you take a few safety precautions before beginning your work. Sharp, heavy duty tools like a table saw must be handled properly and treated with respect in order to see the best results and maintain a safe environment. Click here to find out the best way to sharpen your blades. Before you begin your safety preparations on the table saw itself, you need to take the time to make sure you are properly dressed for your task.
Once again our team has put some serious time and effort into our Head-to-Head evaluation to bring you the most comprehensive information available. For this evaluation, we broke things into several categories including: Precision & Accuracy, Performance (power), Price, and Ergonomics. For each of these categories we’ll rank the saws and at the end we’ll name the Best Portable Jobsite Table Saw based on all the results combined.
The Bosch 4100-09 10 Inch Table Saw is an expert tool that will be sure to impress its users with the reliable design and easy to use set up system. Our favorite feature was the gravity rise design that allows you to push the device around easily and focus more on getting the job done instead of wasting time trying to set up a complicated device. The tool is also coated in a powder coat that helps to improve the longevity of the device and features a collapsible design that is easy to fold up and down once you get to the job site.
The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.
Ryobi’s RTS21G comes in as the only table saw in the group under $200. It’s lightweight, reasonably compact, and we got acceptable jobsite cuts with the upgraded Diablo blade. The throat plate uses magnets to hold it in place while leaving it easy to remove for blade access. Using a threaded rod to push the height adjustment up, you’ll notice it’s easier and smoother on the way down. The stand folds up and can be Velcro-strapped to the back, though it’s a bit wobbly compared to the others when ready for action.
This article is the place to start, and then you can take it from there. My table saw buying guide has all the essential information on table saws you will need, like their classification based on size, portability, motor type, blade size, and the features they come with. You will encounter each of these terms in all the product reviews, which is why you shouldn’t skip reading it.