After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
In layman’s terms, a miter gauge is a device that allows users to set up the angle of the material being cut with a table saw. And while most table saws come with built-in miter gauges, others, well, don’t — which is why the Kreg KMS7102 Table Saw Precision Miter Gauge System is invaluable. Whether you’re replacing an old, worn-out gauge or putting it to use in conjunction with a table saw that didn’t come with its own proprietary gauge, the KMS7102 is specially designed with precision in mind. After all, accuracy is vital to successful woodwork.
It’s not until you get a bunch of saws side by side in the shop that you start to see the difference between a $300 saw and a $500 saw. While the motors are all 15-amp, the more expensive saws have features like soft start to prolong motor and gear life, electronic feedback to maintain blade speed and gearing to maximize torque. If you look under the saws, you’ll see that the more expensive saws also have much beefier motor carriages and better-quality blade-adjusting mechanisms.
A table saw is a powerful tool that makes short work of even large pieces of lumber, allowing you to make rip cuts down the grain of boards, beams, and even entire sheets of plywood. No carpentry shop or professional construction site is complete without a table saw. Deciding which saw is best suited to a given home workshop, furniture production factory, or building site is an important decision and merits careful consideration.
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
This table saw isn’t going to provide near vibration-free performance, and you have to be extra careful about kickback since the base is not as heavy or weighted like a standard cabinet saw. Provided you are careful and work slowly though, it is possible to replicate the precisions of a heavy duty cabinet saw on the job site using DeWalt’s innovative DWE7490X.
Best of all, the XACTASAW Deluxe features a left tilting blade design, an industrial grade 50-inch commercial t-square fence, and an integrated miter gauge for making ultra-precise cuts on the toughest of woodworking materials. No matter the complexity of your woodworking project, this cabinet saw has you covered. This is definitely a world class tool for world class craftsmen, and it is an ideal addition to any woodworking shop whether you are starting out or you’ve been on the job for years.
We’ve approaching the end of the table saw reviews on this page and we’ve selected the GTS1031 10-Inch Portable Jobsite Table Saw from Bosch to conclude those reviews. Our reasoning behind choosing this particular saw is largely because it offers a good all round selection of functionality. As you’ll find over the course of this review, this is a table saw that provides portability, flexibility, power and more. It may not excel in all of those areas but if you’re stuck for choice when it comes to a table saw, this’ll get the job done.
The blade guard is the most noticeable and the most important safety element of every saw. Its purpose is very simple – it keeps your fingers away from the blade. Many people decide to unscrew this part and take it off to speed up the cutting process, but that’s a huge mistake. In fact, a massive percent of injuries happen because people alter the safety mechanisms in order to work faster. Risking your life for a few hours of effective work isn’t worth it, to say the least.
If you are new in this industry, it’s important to know that Makita is one of the most reputable power tool companies out there. For this reason, in our comparison table, you will find one of their top-of-the-line modes, the Makita 2705. It comes with a 15-amp motor which has 4800 rpm. This is more than enough power to cut almost any wood. Despite its large table, the unit has a compact design. The blade guard system has a cam lock, so it can be easily adjusted while the dual guards allow you to cut any wood any size and shape. As far as the safety goes, it is everything okay. Although that some important features are lacking, it still has two independent anti-kickback mechanisms and a blade guard that is designed great. After testing this incredible tool, we can honestly say that it can cut wood with incredible accuracy.
The SKILSAW SPT70WT-01 is one of the most efficient circulars saw on the market. It has everything you need. It is quality, durable and has a great price. It comes with a 15 amp dual-field motor that delivers 5300 rpm and 25 inches rip cutting capacity on the table top. The maximum depth of cut at 90 degrees is 3-1/2 inches while at 45 degrees is 2-1/4 inches. The SPT70WT-01 measures 19.9 x 23.4 x 13.4 inches and weighs 49 lbs.. It is a lightweight unit that comes with a compact design. Its lightweight feature makes it portable and easy to transport from a place to another. Thanks to its 10 in. 24 tooth carbide rip cutting blade, this SKILSAW model has the ability to rip any type of wood. As compared to other similar units, this one comes with a plethora of useful accessories, such as rip fence, table insert, barrier guard assembly, miter gauge, push stick, anti-kickback device, blade wrench, hex wrench and manual.

Buying a table saw can cover a lot of bases. You have everything from DIY models to professional production level cabinet table saws. In this article, we’re looking what is arguably the most popular – jobsite table saws. They’re on the less expensive side and are highly portable compared to their shop counterparts. That makes them go-to tools for framers, jobsite carpenters, and Prosumers.
To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.
For any kind of professional woodworking and large scale construction work, the cabinet table saw is the one for the job. These types of table saws are often called stationary saws. The motor is protected in a cast iron and steel cabinet that reduces noise and vibration as well. With reduced vibration comes better accuracy which is always the desired effect, especially for professionals. The motor us a powerful 3-5 hp and requires a 220-volt outlet. If you are using it in a home workshop, a special outlet may need to be installed if 220s are not already installed in your garage or shop. Measuring about 28” x 43” and weighing in at over 400 pounds, these table saws were not designed to be portable. The large work surface is ideal for cutting large pieces with ease. Cabinet saws can use a 12” blade with no problem, although a 10” blade is the most commonly used. It is the most expensive of all of the styles of table saws.
The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.
The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
If you’ve read through those reviews and still feel a little overwhelmed, don’t worry. We’ve created a buyer’s guide because we know it can be very hard just by reading reviews. After all, some models are going to work better for some people than for others, and the only way that you’ll know which one is right for you is by understanding your options when it comes to table saws. By reading this general information about table saws, you should gain the knowledge you need to make a well-informed decision about your future table saw.
You’ll also want to make sure that you’re getting a model that doesn’t have a problem with internal dust collection. Some don’t do a great job of funneling the dust towards the port, so it ends up sitting inside the unit. This can affect performance, as sawdust is great at gumming up moving parts. So, if you get one of those models, know that you’re going to have to regularly open it up and clean it out to keep it in tip-top shape, which is a pain, but necessary if you want your unit to last a long time.
June 7th! Leather couches (3), storage ottomans (2), queen & single beds, kitchen table & chairs, gliding chair, lamps, end table, washer & dryer, gas blower & weed whacker, 50 in Plasma TV, 19 & 12 in TVs, desk & shelves, metal fire pit, outdoor iron table & 2 chairs, outdoor porch swing & stand, circular saw, jig saw, sander, other assorted goodies! Cash & carry! 972-436-0328
Table saw reviews take the guesswork, and considerable comparative research time-out of the buying equation. Table saw reviews are the result of consolidating the user feedback for the most effective and relevant input. After the data is analyzed, you receive the best of the best, in a condensed version. These streamlined recommendations enable you to spend less time trying to determine which table saw is ideal for your purposes, so that you have more time to use the one you do decide to buy.
This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.

With a quick release riving knife, this Jet 708676PK XACTASAW Deluxe 5HP with 30 In. Rip Fence reduces the risk of binding and also cuts back on the kickbacks that you might otherwise feel. Its five-horsepower motor is one of the most powerful on the market and can make quick cuts in any type of wood. It also comes with a 30-inch rip fence making rip cuts, though you may find that this fence is a little too short your needs.


SawStop has an excellent stand and they’ve cleverly hidden the tool/miter/riving knife storage box under the side extension. Move the table extension and the box presents itself. Like DeWalt, two riving knives come with the saw—one with safety guards and one without. This keeps you from wondering how the pawls and guard go on the riving knife. Blade height fully adjusts with only one turn of the wheel. Not everyone was on board with this, citing less accuracy for dado and rabbet cuts. In the end, we showed we could be as accurate on the height as any of the other saws, so it’s a win.

Hello, Thank you for your comment. We apologize for any issues our Top Table Saws of 2018 blog post has caused. It was not written to be a comparative review of the different saws but a list of the top saws that we are currently selling. It would be unfair to compare performance of a portable jobsite table saw to a industrial cabinet saw and then also compare them on price. If you would like to read a very good comparative post we suggest you check out ProToolReviews.com. They are not tied to any manufacturers and have a very unbiased opinion.
The first step to take when using a table saw is to don all the appropriate safety gear that a responsible operator should use. This includes, at the bare minimum, eye protection and thick work gloves. It's also a good idea to protect your ears with ear muffs or earplugs and to consider a mask that will cover your mouth and nose to prevent the inhalation of fine saw dust particles.
The biggest advantage of hybrid saws is the fact that they can be plugged in a regular 110V/220V outlet. Therefore, you don’t need any additional power sources in order to use these units. It quite a relief because you’ll avoid any further investments. These saws are quite easy to use if you know what you are doing. However, if you don’t, remember to read the manual before turning your saw on. It will save you a lot of hassle and also keep you safe.
It’s a challenge to identify the best portable table saws. They need to be the right mix of quality, performance, price, brand, and availability. In this article, we will attempt to cover all those points for our five tops picks in this burgeoning market sector. Our reviews are designed in a way that can help you concentrate on products that provide a pretty comprehensive package. While the market is full of options, it is always good to go for ones that highlight the unique versatility of this tool. We will also go over everything you need to know in our buying guide so that you can purchase a portable table saw with confidence.
I knew there were jobsite table saws on the market for less than $250, but I never thought they were good enough to get my recommendation. Sure, the SKIL 3410-02 is not a professional saw and may not be versatile enough for contractors, but the stand, power, accuracy and build quality of this table saw are much better than I thought possible in this class.
×