When you need to change the blade, you’ll find that this saw comes with an arbor lock that you can unlock with one hand, which lets you change the blade without any special equipment. It uses a poly-v drive belt system that gives the motor extra power, but this belt system also reduces the noise of the motor, which makes it great those working around others.
The Bosch 4100-09 10 Inch Table Saw is an expert tool that will be sure to impress its users with the reliable design and easy to use set up system. Our favorite feature was the gravity rise design that allows you to push the device around easily and focus more on getting the job done instead of wasting time trying to set up a complicated device. The tool is also coated in a powder coat that helps to improve the longevity of the device and features a collapsible design that is easy to fold up and down once you get to the job site.
Almost all the features you like about the more expensive SawStop cabinet saws are available in this PCS31230-TGP236 3-HP Professional Cabinet Saw Assembly with 36-Inch Professional T-Glide Fence System, Rails and Extension Table, which costs much less. This model comes in a black finish with accents and features like its emergency stop button in a brighter red color that make those features easy to see. It also features a taller height designed to reduce strain on your back as you saw.

Innovative Gravity Rise Sand – When it comes to the features of Bosch’s 4100-09 table saw, there’s clearly only one place to start and that’s with the Gravity Rise Stand that comes as part of the package here. This is basically a stand that can be intelligently adjusted to your liking and then wheeled away when you’re finished using the table saw. It’s a pretty innovative idea from Bosch and definitely one of the best stands that we’ve seen included with any table saw that we’ve reviewed or on the market.

Another indication of how hard a table saw is working is monitoring the amperage (AMP) draw under loading conditions. We measured the amp draw for each saw using all three materials again at the same time we were recording RPMs. The first graph below shows the amp draw for each saw cutting plywood compared to the no-load amp draw. The white bar on the left indicates the no load amps and the colored bar on the right shows the maximum amp draw during the cut.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
I really do like your site and being on Long Island there is a familiarity to the way y’all work. You are quick to respond to comments and put in a great effort but…. This review I feel you miss the mark. Out of box accuracy is important but. Ore important to a pro user is tool able to be adjusted to be near perfect and how does it hold this position. No comments on how solid the fences are, ie deflection movement, ease of micro adjust, etc. all the fancy self feed stuff etc, what saw feels the most powerful? Smoothest ? All theses kizmos are for the manufacturers to hype. Your strengths are that you actually use these machines, so your strengths are to BE MORE opinionated or biased not less because your opinion has meaning or weight. Let the know knowings use the kizmos and just give us your real opinions based on real use. Just my 2 cents.
The final key factor that you’ll want to take into consideration when picking the right table saw is just how easy that table saw is to use. Obviously for experienced table saw users, ease of use might not be something that is so much of a big deal, but if this is going to be your first table saw, it’s definitely something that you’ll want to look out for. The last thing you want is to purchase a brand new table saw and find that you can’t use it.

With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
Some craftsmen are looking for a cabinet table saw that has both a small footprint but doesn’t sacrifice performance when it comes to cutting and shaping hardwood. If you are that craftsman, then the Grizzly G0690 was built with you in mind. With a 220-volt 3 horsepower motor, this smaller scale cabinet saw is built to rip and split some serious hardwood with minimal effort.

If you’re in the market for a powerful table saw that can provide premium performance at an affordable price, you need to look no farther than the   SKIL 3410-02 10 Inch Table Saw. This device is powered by a 15 amp motor with a 120 Volt power requirement and is capable of tackling some heavy duty projects. The kit comes with blades, a miter gauge, blade wrenches, easy mount system, an EZ view measurement system, and a steel fold stand.
Like the last SawStop table saw that we looked at, this one is quite heavy and provides the stability that you need when working with plywood or any other type of wood. You can use the foot pedal on the bottom to operate the saw, but you’ll also find four wheels on the bottom of the cabinet. All four of those wheels swivel in a 360-degree direction to help you move the cabinet to any location.
You often find that many contractors have a love hate relationship with blade guards. Many contractors and woodworkers simply find they often get in the way and can often get wood stuck in them. But many manufacturers are improving these guard’s year on year and now many of them are very advanced and will help keep your fingers from getting hurt, we always advise you to consider the table saw blade feature on any table saw in detail as it could one day help saw you.

An excellent choice both for professional woodworkers and hobbyists with a more expansive tool budget, the Shop Fox W1819 is a 10 inch table saw ideal for making clean cuts along greater lengths of material without pinching or kickback. The blade itself is covered while in operation by a clear polycarbonate blade guard that moves back as the workpiece is passed along over the blade.
If you already own one or more power tool products in Bosch’s range, then you should find that your table saw works comfortably with that. It’s also worth mentioning that Bosch have clearly targeted their power tool products at the general audience, more so than Dewalt who as we’ve already mentioned have designed their products for professionals. Either way, you’ll find that both brands similarly and comfortably offer a good quality cutting experience through their ranges of table saws.
It has a brilliantly powerful 15 AMP motor, which can deliver 4,800 RPM of cutting power. Is is normally more than enough for most woodworkers and hobbyists. It has stowable anti-kickback pawls and and excellent riving knife and spreader for accurate cuts. This is a great entry level saw at a great price, definitely worth looking at for your next purchase or project.
Paul – Good catch….I’ve updated that to say Skilsaw not SawStop…thank you! As you can imagine…all the data makes it tough to keep it all straight. I’m not even sure how you’d install that aftermarket fence on these saws. If you do I’d love to see how!! Those really look like they are made to install on cast-iron full size saws. I’d choose the DEWALT with a slight edge over the SKilsaw.
You’ll also find that the metal roll cage base will give you extra strength and durability to work with and the rear feet will enable you to adjust the height of the machine should you be faced with the challenge of working on an uneven surface. There’s nothing the DEWALT DW7480 Compact Job-Site Table Saw can’t handle. You’ll quickly be impressed by its ability to tackle any project you throw at it and learn to appreciate it for the great tool that it is.
With many different options available to both experienced and aspiring woodworkers, choosing the right cabinet saw for your workshop can feel like a daunting task. To help you narrow down your choices and better assess your needs, we’ve reviewed the ten best cabinet saws on the market. Regardless of your intended purpose, there is something here to fit everyone’s needs and budget.
I have another post for Woodsmith magazines. ShopNotes 2.00 each copyIssue 1 Premiere Issue Shop -- Built Router TableTable Saw AccessoriesTips for Accurate CrosscuttingElu Router ReviewIssue 2Wooden Joiners MalletStorage Bin SystemHand-Cut MortisesRadial Arm Saw FenceIssue 3Handy Tool Carry-AllShop-Built Cling StationPlate Joinery TechniquesAdjustable Grinding JigIssue 4Shop-Built Panel SawThi...
Other than getting a cutting tool that will lighten your work, investing in an item that will ensure you are satisfied by its construction, performance and longevity are the desire of every customer. DEWALT understands better the needs of various customers and has been in the business for a long time. The many year’s experiences have given the company trust in customers. Therefore, they manufacture strong tools with high performance and back them with a sustaining warranty. The table saw is designed with a portable style for use in any room comfortably.  15 amp, gives a powerful and consistent performance to ensure you don’t have pending jobs on various days. The large rip capacity makes it easy for you to cut even large materials comfortably. When using this saw, all you need is to keep your eyes open, it has a guide system that will provide accuracy and precision in your work automatically.
There are a lot of great table saws on the market, but we’d have to say the best is the DEWALT DW745 Compact Jobsite Table Saw. This design enables you to be flexible with where you set up shop as well as extremely efficient thanks to the innovative technology that was incorporated into the design. Additionally, it has a 15 amp motor and a 20-inch rip capacity that makes it more than capable of taking on any challenge you throw at it.

Deciding on what portable saw to get is not an easy task. There is so much out there on the market and such a wide combination of options. You can use our top 5 picks to get a taste of what’s out there and maybe find your perfect portable power saw right off the bat. However, we feel that you should also be equipped with the knowledge to go out and make your own decisions on portable table saws. We are going to run through the most important factors and features to consider before you make your purchase. These are factors that have a direct impact on performance.
The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.

​The saw does not easily detach from the stand. Sometimes it’s beneficial to set the saw up as a bench-top saw, but the DeWALT 7491RS doesn’t come with quick release levers to accomplish this easily. In this case, you would have to use a drill to remove four screws to detach it from the stand. I wouldn’t recommend doing this unless you have to because over time the screw holes will strip.

When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.
These tests and evaluations are very difficult, take a lot of time, and ultimately limited in scope as we’re not a professional testing company and we’ve got limited time to evaluate the tools. We cannot do longer term testing that would shed light on durability and we can’t possibly test every application that you might use of one of these saws for. However, we feel comfortable that all the table saws in this Head-to-Head are good saws and our testing helps bring to light pros and cons for each saw.
If you’re going to have a quality product, you need a fence system that’s perfectly square to the table so your cut is perfectly parallel to the edge. Obviously, framers have a bit more leeway than jobsite carpenters and there’s plenty of variance in fence quality. Cheaper saws have fences that can easily move out of square as they slide along the surface of the table. Avoid these if you want quality results. The fence system needs to be easy to keep square to the blade.
Though this SawStop ICS53230-52 5 HP 230V 60 Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System is the most expensive model made by the company, we moved it to the bottom of our list because other cabinet saws received better reviews from customers. This saw comes with a 52-inch T-Glide fence system that helps you set the size and angle of each cut, and this system has a lockdown feature to keep the wood from moving.
Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. The Makita was given the best score of 1 as it was considerably quieter than the remaining. DEWALT and Delta were ranked worse with a score of 3, while the remaining were ranked as a 2.
I have a couple questions about your methods and precision. The no-load rpms for the different saws were very different from replicate to replicate for the three different materials. Wouldn’t you expect the no-load speed to be fairly consistent for each saw regardless of which material was going to be used to add load? With that amount of variability in the no-load speed, I wonder how precise any of the measurements were under load?

With a three-horsepower motor inside, this SawStop ICS31230-36 3HP 230V 60Hz Cabinet Saw Assembly with 36-Inch Industrial T-Glide Fence System is suitable most of the jobs you have in mind. Its industrial T-Glide fence system lets you make all the cuts you need, and the extension table gives you more room to work too. It also features a system that locks the wood in place to ensure that you make the accurate and completely straight cuts that you need.
We put our hands on 10 of the most popular table saws and tested them for accuracy, power, and functionality. It took some time, but we have some fairly conclusive results. Table saws are undeniably the kings of rip cuts on the jobsite and in shops. The concept is simple: Place a motor below a solid table to turn a blade somewhere in the 4000-5000 RPM range through the surface and watch the sawdust fly. The idea may be simple, but the reality is much different. How big should the table be? What size blade should you use? How heavy can you get away with making it? For this shootout, we’re looking specifically to find the best portable jobsite table saw.
You’ll also find that the metal roll cage base will give you extra strength and durability to work with and the rear feet will enable you to adjust the height of the machine should you be faced with the challenge of working on an uneven surface. There’s nothing the DEWALT DW7480 Compact Job-Site Table Saw can’t handle. You’ll quickly be impressed by its ability to tackle any project you throw at it and learn to appreciate it for the great tool that it is.
Still featuring the T-Glide Fence System for smooth, safe operation without compromising on precision measurements and secure locking for repeatable cutting, the TGP236 is still an exceptional cabinet saw in its own right Furthermore, the blade height and angle are still fully adjustable via the comfortably large hand wheels on the front and side of the cabinet itself.
Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.
Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.

We don’t always post the point totals when we do a shootout like this because it gets complicated – you have to decide what the important features and performance categories are, determine how much weight each one should hold, and then actually hash out the scores with the team. That said, some of these table saws scored so close to each other that I didn’t feel it was fair to just leave it up to the rankings.

Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
DEWALT® table saws are available in both cordless and corded. Our portable table saws are compact for easy transportation between jobsites. They offer a rack and pinion fence system for fast, accurate fence adjustments. Our table saws are lightweight and feature a metal roll cage to ensure they can stand up to a rough jobsite. Tool-free guarding component adjustments make it faster and simpler to adjust as needed. Since the World’s First FLEXVOLT® cordless table saw was introduced, DEWALT has revolutionized the world of cordless construction tools. Every aspect of our table saws are designed to make your job easier.
The purchase of a table saw is no doubt a big investment. But there is a lot of flexibility in this class of tools to find one that fits in with your budget and your wants. Make sure to take into account how you will need to use the tool and where you will need to use it. Heavier models will be sturdier but they will also require more effort to load up when you need to.

Looking to purchase a portable saw for your DIY projects? Are you interested in funding some quality tool to cut large pieces of wood properly? Then, take a look at this incredible model. When buying this kind of tool is very important to understand several things including its capabilities. When it comes to accurate cuts and quiet operation, the DEWALT DW745 could be exactly what you are looking for. It is a popular model that comes with a lot of impressive features. It comes equipped with a Pro Modular Guarding System for increased accuracy. It is powered by a powerful 15 amp motor and it has a large 20-inch rip capacity. Thanks to its powerful motor, it delivers a no-load speed of 3850 rpm. Also, it should be noted that it uses blade guards. Plus, it comes equipped with a miter gauge, a push stick and a dependable 10-inch, 24-tooth carbide blade. The DW745 is covered by a 3-year limited warranty and 90-day money-back warranty. In addition to this, there is 1-year free service.
Accessories 10″ 24-Tooth Carbide Blade, 2x Blade Wrenches, rolling stand, blade guard assembly, push stick, miter gauge, rip fence 10 in. 40-tooth carbide-tipped blade, throat plate insert, smart guard system, rip fence, miter gauge, push stick 32T carbide-tipped blade, rip fence, miter gauge, push stick, and wrenches Rip Fence, Miter Gauge, Smart Guard System, Push Stick, Blade Change Wrenches 24-tooth SKILSAW Carbide-tipped blade for ripping, miter gauge, self-aligning fence, guard system including anti-kick back device, insert plate, push stick and wrench
Table saws in this best table saw review run the gamut in price and quality. You can buy a table saw for as little as $150, and if you use it just to occasionally rip a board, that may be all the saw you need. If you want a saw that’s easy to carry and you don’t need to rip sheets of plywood in half, look for a “compact” saw like the DeWalt DW745 (shown) or the Bosch GTS1031. If you have room for a little larger saw that’s slightly less portable but capable of wide rips, consider one of the best table saws we review here. And finally, if you want to build cabinets or furniture and have a big enough work area, you can step up to a stationary contractor’s saw like the Ridgid R4512 (shown), for about $650.
×