First up is the portable table saw. There are two variations in this category, the first of which is the benchtop. As the name implies, the benchtop table saw is designed to be used on top of a table or bench. They’re small, so that it doesn’t matter which table or bench you put them on, and they’re light enough to be carried from place-to-place. This type of saw was originally meant for construction, but that doesn’t mean that you can’t get good use out of it in your shop or garage.
Dust Collection Port – Using any table saw is guaranteed to generate an awful lot of dust and anyone who suffers from asthma will know this to be a big problem. With that in mind, it’s nice to see that DEWALT have taken precautions to allow you to properly extract dust when using your table saw. This is through the product’s 2-1/2-inch dust extraction port that allows you to quickly and easily connect a vacuum for efficient dust extraction. If you’re going to be regularly using your table saw, you’ll definitely notice the advantage of having dust automatically extracted out of the environment for you.

Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.
The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.
We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
Table saws will continue to be popular and much sought after tools in any workshop or construction site. There are many terrific styles on the market which is why it is important to do some research and look at the reviews provided here as well as the tips contained in this guide to help you choose the right table saw for your needs, whether you are a professional or a DIYer who loves to work in the workshop making things for enjoyment.
I got the Hitachi 1 1/2 mouths in the motor died. Says it has a 5 year warranty. I’ve been trying for weeks to get it resolved. Ended up giving up and headed to buy another saw. I understand having products be faulty it’s a numbers game it has to happen to some one. How ever the complete no help to resolve it from Hitachi. Is a problem after a week of back and forth they said they would set up a pick up time to ship and get it repaired over a week still no call back for a pick up. I can’t say enough avoid this headache. I’ve been a contractor for a decade and have had may tools break or need repair. First experience I’ve had that’s made me swear off a brand.hope this will save some one from wasting money and time
You will need specialty blades for cutting materials such as plywood, masonry, hardwood and metals. Other specialty blades are used for dado cuts. Most dado sets have multiple rows of teeth and chippers and they are typically much wider than traditional blades. Be sure that the model of table saw you have can accommodate the type of specialty blades you want to get so you don’t waste your money on a blade that won’t fit.

Great match-up and informative… however I too noticed that “No Load” RPMs varied quite a bit from chart to chart – for the same saw. We would expect some variation of 50 RPM as you had mentioned, but not 500 to 800. See that the Hitachi changed from 4400 down to 3700, Delta jumped from 3700 to 4400, Rigid from 3650 to 4350. Upon closer scrutiny… the order of “No Load” RPMs used in first chart may have been used in all subsequent charts. When the “Load” results were ordered by hi-to-low ranking, is it possible that the “No Load” data was not kept with its saw? If so, that changes the %drop results slightly for most RPM No-Load/Load,Speed charts. No too terrible. Lots of data… Good overall presentation though for use to make informed decisions. Thank you!

Every woodworker knows the plague of working in a dusty environment. The SawStop has a fantastic dust collection system so you can enjoy your cutting without your eyes being strained. Almost all of the dust is wicked away both above and below the table. Up above, the blade does all the legwork and there’s a neatly designed shroud which pulls all this dust away from the blade. The 4-inch port means you can slip your shop vac on with no issues.        
Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.
Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. The Makita was given the best score of 1 as it was considerably quieter than the remaining. DEWALT and Delta were ranked worse with a score of 3, while the remaining were ranked as a 2.
This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.

A gauge will allow you to make very detailed cross and angled cuts. This is a bit of kit that you need to research in great depth as it can make or break the accuracy of your cuts and angles. With a good gauge, you can check blade height, blade angles, miter angles and much more. For further reading checkout Wikipedia’s table saw page and for in-depth air compressor reviews.
When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.
We took all of the data from the RPM and AMP measurements and added them to come up with the final performance rankings. For each saw we added up the total percentage decrease in RPM’s (for each material type) and added that to the total percentage increase in AMP’s (for each material type). This gives us a relative comparison of each saw over all 6 sets of data.
Scott – I’m assuming you’re talking about the “flatness” of the table and not leveling the saw correct? I will tell you that all jobsite table saws use light weight tables that are NOT machined cast iron like shop saws. Most of the jobsite saws are a light weight cast aluminum top, and NOT machined flat. So there are tolerances in the manufacturing that make it impossible to get a really flat surface. The thing is, in my opinion, for this type of saw it’s not really important. Job site saws are set up for ripping framing lumber, trim, and details that are not as precise as “woodworking” projects. If you need a cut that precise on a job then there are other better approaches including track saws and even pre-cutting materials in the shop. The DEWALT is very similar to the other saws with regard to the table.

Next, you’ll want to focus on protecting your eyes. You’ll need a sturdy pair of safety goggles to make sure you keep your eyes covered at all times. If you don’t take precaution with your eyes they could become injured or irritated by debris that is kicked back from the machine or sawdust that floats in the air. Having itchy, irritated, or otherwise injured eyes is a work hazard that is best to avoid – not having clear eyesight complicates things greatly and puts you at risk for other injuries.
Methods for tilting the blade to cut bevels vary among the saws. The Porter-Cable saw is the only one with a conventional handwheel bevel control mounted on the side of the saw. The crank gives you great control for setting an exact angle. To set the bevel on the Bosch, DeWalt and Rockwell saws, you simply release the bevel-lock lever and tilt the saw to the preferred angle. It’s easy to go quickly from a 90-degree to a 45-degree bevel with this method. The Ridgid, Craftsman and Ryobi saws have a rack-and-pinion setup. These saws utilize the front crank for setting the bevel.
Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.
Bosch’s 4100-10 work site table saw is a sure win. Bosch never fails to impress us, and this table saw is no exception. It’s a 10 in. saw with a 25 in (right) rip capacity and a 47 degree left bevel. This Bosch table saw is powered by a 15A motor that reaches top speeds up to 3,650 RPM. Another feature we appreciate: its constant response circuits which continuously adapt the speed under load, giving you a continuous blade speed.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.
Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.
From the triple belt drive system, to the three-HP motor and the large cast iron table and wings, the Shop Fox W18193 s built like a tank. You’re also going to love the T-slot miter gauge that features a fence extension and flip stop, but also a four inch port for dust collection and camlock T-fence. There’s also a twenty nine and a half inch rip capacity.
You’ll also find that the metal roll cage base will give you extra strength and durability to work with and the rear feet will enable you to adjust the height of the machine should you be faced with the challenge of working on an uneven surface. There’s nothing the DEWALT DW7480 Compact Job-Site Table Saw can’t handle. You’ll quickly be impressed by its ability to tackle any project you throw at it and learn to appreciate it for the great tool that it is.
The biggest advantage of hybrid saws is the fact that they can be plugged in a regular 110V/220V outlet. Therefore, you don’t need any additional power sources in order to use these units. It quite a relief because you’ll avoid any further investments. These saws are quite easy to use if you know what you are doing. However, if you don’t, remember to read the manual before turning your saw on. It will save you a lot of hassle and also keep you safe.

There are two major points that affect post-calibration table saws: fence quality and overall stability. A fence works by grabbing hold of the table edge and clamping into it. The best fences, like Biesemeyer, have three points of contact. They’re just not where you’d expect. All three are on the front, leaving none on the back. With a wide cast metal front clamping system, the front is pulled flush and self-aligns. It requires a solid locking mechanism to ensure the fence doesn’t move during cuts, but it is very possible.
It is extremely lightweight so that it can be easily moved around. The best feature for me is the unique capability to capture dust both below and above the blade. That keeps your workplace clean, and you save time. The safety features and ease of use further add to the convenience element. Additionally, the product comes with a 3-year warranty, which is quite good for a tool in this class.
Our selection the top cabinet saw is the SawStop ICS51230-52 5 HP 230V 60 Hz Cabinet Saw with 52-Inch Industrial T-Glide Fence System. SawStop appears on our list a few times because the company makes saws that come with its own patented safety system that causes the blade to stop spinning as soon as it comes into contact with skin. We also like the extended fence system on this model, which accommodate more wood types and board lengths.

SawStop is the only saw in the group to employ this style fence and they have the best in the group. Ridgid comes in second with a traditional front clamping fence system that has a backside contact point. Its solid construction and wide cast front clamp left us impressed. DeWalt’s came in third with an innovative effort that locks into several points based on where you need it. Rather than sliding along, it stays in place while the rack and pinion system moves it into place. It’s not perfect, but it eliminates a lot of accuracy issues that come from locking the fence out of square on some systems.
All table saws sold in the U.S. come with a riving knife, anti-kickback pawls, and a split blade guard. Because some cuts can’t be made with these safety features installed, they are removable. If you’re looking for a fun party game, see who of your uninitiated friends can install both correctly without a manual. While each one is different, their nature means you can use the saw without them installed. I’d be remiss if I didn’t tell you those cuts are more dangerous, so avoid it if you can.
Another excellent choice for the hobbyist or at-home handyman, the SKIL 3410-02 10-Inch Table Saw is a great value, giving you a durable build and quality performance at a wallet-friendly price. It doesn’t have the same brand recognition as some of the more expensive options on this list, but reviewers love this machine and say that it’s perfect for woodworking and DIY projects.
Once you’ve gathered your materials, turn your attention to the plate in the middle of the table saw. It surrounds the blade and should have two screws that hold it in place (however some models will have four). Use your screwdriver to undo these screws and set them aside. Then take the plate off and set it to the side as well. Then check to make sure the blade is at its full height by going to the back of your table saw and winding the blade up to full height.
I really enjoyed your review and appreciate the significant time and effort put into it. How did you acquire the machines? Were they evaluation units provided by the manufacturers or did you buy them (randomly, like Consumer Reports)? If they were provided to you the cynic in me says you probably got cherry picked units. In looking at the various machines on line and checking out their comments, it’s quite clear pretty much all of them have a manufacturing distribution of performance and metrics e.g. for accuracy all the units you tested have comments ranging from great to truly awful. Same thing for build quality. I spent quite a while looking at the Dewalt but all the negative reviews on quality and accuracy turned me off it. I certainly do see many more positive reviews than negative reviews for the Dewalt, but it does leave you with the feeling that a dice roll is partly involved in buying a recommended table saw.
When you need a full size cabinet saw that can handle just about any woodworking job you can throw at it, the Powermatic PM2000 is the one for you. As with all high end cabinet saws, the PM2000 features box-style cast iron trunnions for that refined, precise feel when adjusting the blade angle and height. Front control wheels are user-friendly cast iron hand wheels that feature precision-machined center locking pins for making every cut consistent and repeatable.

The first contractor saws were made to be portable so they could be taken to job sites. These are also lightweight and priced low enough that the handy homeowner can use them. When purchasing the contractor saw there, you will have to make a few concessions. The table is not made of the cast iron top and the extensions are usually made of stamped medal. It is not made as burly as more costly saws. The motor also hangs off the back, which makes it easier to remove when moving the saw to another job site. Bosch table saws are reported to be one of the best budget saws available.
Best of all, the XACTASAW Deluxe features a left tilting blade design, an industrial grade 50-inch commercial t-square fence, and an integrated miter gauge for making ultra-precise cuts on the toughest of woodworking materials. No matter the complexity of your woodworking project, this cabinet saw has you covered. This is definitely a world class tool for world class craftsmen, and it is an ideal addition to any woodworking shop whether you are starting out or you’ve been on the job for years.
Table saws that can be found on the market are designed for different uses. There are four types that these table saws can be listed under. There are Portable saws, contractor saws, hybrid and cabinet saws. When exploring the possibility of a new saw you will need to understand what each of these mean and how each saw performs in their perspective class.
It’s worth remembering that contractor table saws are still going to be pretty portable because they’re designed to be used by contractors. That being said, unlike portable table saws, they don’t necessarily fold up into a compact position. This is largely because contractors tend to have the facilities needed in order to transport a larger bit of kit. The extra space that they take up in comparison to a portable table saw means that contractor table saws are able to offer a greater level of power and precision. Both of these points further support the fact that contractor table saws sit in the middle ground.

I have many bundles of old barn boards for sale. These boards are close to 100 years old if not older and they have all had the square and round nails removed from them. This lumber is completely dry and I am selling them in different sized bundles for those who need different amounts of lumber. The old circle saw marks are clearly visible on each board as seen in the pics. Many people use old ...
Other features include two handwheels with measurements around each one that you can use to set up your cuts or as you cut and an emergency button that acts like a kill switch to pull power from the motor during an emergency. This cabinet saw comes with an easy change system changing the blade and a warranty that covers the saw two years and the motor five years.
There are two major points that affect post-calibration table saws: fence quality and overall stability. A fence works by grabbing hold of the table edge and clamping into it. The best fences, like Biesemeyer, have three points of contact. They’re just not where you’d expect. All three are on the front, leaving none on the back. With a wide cast metal front clamping system, the front is pulled flush and self-aligns. It requires a solid locking mechanism to ensure the fence doesn’t move during cuts, but it is very possible.
One of the most widely used power tools for carpenters is the table saw. For carpenters that don’t work exclusively in the shop a portable jobsite table saw is essential. For this Head-to-Head we’re focusing on corded portable 10″ jobsite table saws. We are not including cordless table saws in this test as we plan on doing another head-to-head exclusively for cordless table saws later this year as several are available now.
If you’re looking for the perfect cabinet table saw out there, then you should look no further than the SawStop ICS51230-52. This is an industrial grade cabinet saw and is also the highest quality, most powerful and heaviest cabinet saw you can currently get. Its fifty two inch industrial T-glide fence assembly, combined with a 5 HP, 230V single phase motor offers safety, versatility, durability and peace of mind that SawStop is so well known for.
Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.

One of the first things many Pros do is permanently (and intentionally) lose the blade guard and anti-kickback pawls. While they are a pain to install and store onboard, their ability to reduce the risk of injury is significant. Table saws are responsible for thousands of injuries every year and there are plenty of guys running around with stories of how they got injured. So practice installing them until it feels natural and then actually use them onsite.


The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. There is tool-less assembly of the riving knife and anti-kickback pawls. It has a large easy to access ...  More + Product Details Close
You’ll also want to be sure to check that the teeth of the blade are facing towards you since this is the direction that the wood is cut. Once you’ve made sure that the new blade is on properly you can put on the stabilizing parts and nut again. You’ll tighten the nut by putting the spanners on the same way you did before, however, this time you’ll push the spanner in your left hand away from you to tighten the nut instead of towards you.
I do not which is the best table saw, but I can tell you which is the worst. The rigid portable saw is a piece of garbage. I have purchased two in the last 4 years and the motor has failed in both, only to find that they do not sell a replacement motor. The Rigid customer service will not respond to any questions associated with the saw or replacement parts. I will not buy another Rigid tool and currently planning to try the Bosch table saw.
For carpentry projects or as a starter saw, the DeWalt DW745 receives solid reviews. Though it doesn't have the capacity of the Bosch, owners say it's well made and easy to adjust. The rack-and-pinion fence earns kudos for accuracy. The saw weighs just 45 pounds and can even be hung on a workshop wall for storage; an optional is also available. The three-year warranty is another plus.
We spent 42 hours on research, videography, and editing, to review the top options for this wiki. Regardless of whether you're a construction professional, a precision woodworker, or a DIY hobbyist tackling your next home-based shelving project, one of these handy table saws will help you get the job done fast. Our selections include models with durable cabinets, powerful motors, integrated fence rails, and even patented safety systems to protect you from on-the-job injuries. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best table saw on Amazon.
Probably one of the things that users will love most about this table saw is the solid granite surface which offers a seamless work area and excellent support. Another advantage of the Steel City 35955 is the fact that it comes with powerful magnets which allow swift changes without having to worry about using any type of tools. Since there’s a built-in mobile stand, you can easily position the saw around your shop without requiring the help of a second person.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
At the same time, it’s also worth mentioning that Ryobi offer some of the most affordable products that we’ve seen from many table saw manufacturer. If you don’t particularly fancy shelling out some of the high prices that both Dewalt and Bosch are selling their products for, looking into the range offered by Ryobi might save you a serious amount of cash.
First, this is not a precise table saw.  This is due to a mix of design flaws and poor manufacturing choices. The placement of the blade guard makes it impossible to see the blade during the cut, which is going to make you less precise and frustrated to boot. The fence is cheap, and may or may not be straight, but even if it is, you have to deal with the fact that flaws in the table itself may result in it not clamping down straight.
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.

It is an extremely durable and sturdy product. However, there are some drawbacks. First of all, it is expensive without quite backing up that price in all areas. It does not really have the elite safety feature of our top choice, and it also lacks high-end power. These are minor points (it is still safe and powerful), but you expect it to be perfect at this price.

Framing work is full of rougher cuts that rarely makes use of more than one blade at a time. But occasionally you might need dados for an onsite custom build in. If that sounds like you, be sure to find out the saw’s dado stack capacity. It requires a longer arbor and you won’t be able to use your normal throat plate for it. Some manufacturers offer a dado throat plate if they have the capacity for it.

Depending on how often you work with wood and the type of wood that you use, you may find that this SawStop PCS175-PFA30 1.75-HP Professional Cabinet Saw Assembly is better suited to your needs than some of the company’s more expensive models are. This saw features a smaller base and a shorter extension table that take up less space, but you can use the fencing system to extend the size of the table working with your boards.

At first glance, the Bosch 10-Inch Worksite Table Saw may seem to be nothing exceptional. However, it's powered by the best motor in its class, and it does everything well. True, the motor is a 15 amp unit like the others on our list, but it produces 4 HP where the others produce only 1.5 to 2 HP. This is a noticeable step up in a vital area! The wheeled frame is extremely helpful for moving around your shop or garage, but keep in mind that those tires aren’t heavy-duty; you have to be careful with them on a worksite littered with nails and screws.
Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.

Table saws are very efficient tools that have proven their worth to woodworkers and DIYers alike. They enable people to cut down and craft wood much more efficiently, but there are a few things you should know about proper use of a table saw before you begin if you want to achieve the best results. The first is to use the blade guard and log splitter to make your work easier to accomplish and a more safe environment.
The only flaw might be the occasional false detection by the safety system. This will usually only happen if the lumber is wet or it is used primarily in the outdoors. You have to weigh the safety features against the type of work you do. If you are constantly working in wet or damp environments, it might not be worth the headache. If not, it’s 100% worth the benefits!
The good news is that if you already own a dust collection system or a shop vac, then you may be compatible with many models. Even if it doesn’t match the port size of your shop vac, you can often purchase converters that will make the table saw work with the system you already own. Consequently, you shouldn’t avoid a unit because it has a port size that is different from the gauge of your shop vac. This is something to look into before making a purchase, just to make sure that converters that will work with your model are being sold.
Bigger tables offer more potential for additional extensions. For example, if you’re planning to process a massive piece of wood but you cannot cut it in smaller pieces; a table extension will definitely come in handy. There are a lot of commercial add-ons you can choose from, but you can also construct one yourself if you’re experienced enough. Experimenting with these things never gets old or boring, but keep safety in mind at all times. Make sure it’s completely safe to use the said extension and pay special attention to the amount of vibrations and the overall integrity of the table after you’ve installed the add-on.
×