This “review” is a giant nothingBurger. There is not one scrap of objective comparison between these saws. Because you sell them, they’re all great and will all zip right through “the hardest woods”. Bulll$hit. You did not test, compare, analyze, or use ANY of these saws. Re-hashinf manufacturer specs is a “Roundup” but it certainly is not a review. Typical sales pablum.
Flesh Sensor: This is another very important safety measure. While it is possible that this might raise the cost of the saw, nothing is more important than your good health. Flesh sensors stop the blade immediately when they sense a finger on the blade. So instead of a severed finger, you get away with minor cuts. Always choose minor cuts over missing fingers! You do not want to be going to the emergency room with an ice box.
Now you’re ready to advance on to the next step. Take the spanners out and get ready to put them on the nut. You’ll want to make sure that they are the spanners that originally came with your table saw because they have been tested especially for your machine to make sure they won’t over tighten the nut or screws. Once you’ve made sure that you have the correct spanners, place them on the nut. Use the first spanner with your right hand and use it to stabilize your grip.

Contractors who do a lot of finishing work and interior/exterior trim work know the value of a good portable table saw. DeWalt has built the DWE7490X from the ground up as a stable and safe job site cabinet saw that can be used to make those precision cuts quickly and easily without the need to pre-fabricate materials and then bring them to the job site for final fitting.

From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.
Powerful cutting and portable convenience with the Delta Powerful cutting and portable convenience with the Delta 36-6022. The 1-step release stand and large wheels make it easy to move the saw to any jobsite. The 15 Amp commercial grade motor cuts through the toughest materials. UL approved 3-way guarding system with riving knife for safety and excellent dust ...  More + Product Details Close
At first glance, the Bosch 10-Inch Worksite Table Saw may seem to be nothing exceptional. However, it's powered by the best motor in its class, and it does everything well. True, the motor is a 15 amp unit like the others on our list, but it produces 4 HP where the others produce only 1.5 to 2 HP. This is a noticeable step up in a vital area! The wheeled frame is extremely helpful for moving around your shop or garage, but keep in mind that those tires aren’t heavy-duty; you have to be careful with them on a worksite littered with nails and screws.

Once again our team has put some serious time and effort into our Head-to-Head evaluation to bring you the most comprehensive information available. For this evaluation, we broke things into several categories including: Precision & Accuracy, Performance (power), Price, and Ergonomics. For each of these categories we’ll rank the saws and at the end we’ll name the Best Portable Jobsite Table Saw based on all the results combined.
Additionally, the bevel dial is accurate to within ¼ of a degree, making ultra-precise angle cuts easily repeatable. The base of the 36-L552 is also constructed of solid cast-iron, adding balance and stability even when cutting through the toughest hardwood. An aggressive blade guard and splitter design also helps prevent both accidental contact with the blade and pinching or kickback from the kerf even on extended cuts.
The table measures up at 29 inches by 21.5 inches. The 4100-09 is not suitable for dealing with large stock or sheets of wood. Made from aluminum, you’ll meet with no resistance as you slide the timber toward the blade. The only negative with the table is the way it’s finished with an anodized coating. This is fine to start with but tends to wear over time, something that doesn’t just look unsightly but can ultimately affect accuracy. This is a surprising oversight from Bosch and one we hope they rectify in future iterations of this fine table saw.
Probably one of the things that users will love most about this table saw is the solid granite surface which offers a seamless work area and excellent support. Another advantage of the Steel City 35955 is the fact that it comes with powerful magnets which allow swift changes without having to worry about using any type of tools. Since there’s a built-in mobile stand, you can easily position the saw around your shop without requiring the help of a second person.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
This is the smallest of all the table saws, typically weighing about 50 pounds or so and designed to sit on top of a table or workbench. Bench style table saws are usually made of steel, plastic and aluminum. They are good for light to medium duty cutting and would not be a good choice if you do a lot of cutting or if you have a professional business. Because it can be lifted by one person and moved around with relative ease, this type of saw is often called a portable table saw. Due to the size of these saws which measure approximately 19” x 27”, they are not designed to rip large pieces of wood. It is also not easy to make mitered cuts. You will notice that there might be more vibration when using this saw as compared to other, larger models. This is due to the lighter weight of the saw. Unfortunately, the vibration can affect the accuracy of the cuts you’re making.
This next factor to take into consideration when it comes to buying a table saw is more of a safety feature but one that you’ll want to look for in every table saw. It’s basically an automatic switch that turns of the table saw when you walk away. It’s often the case with some cheaper table saws that when you’ve finished using the table saw and forget to flick the power switch, the unit will remain on. This leaves anyone who goes near the table saw open to a considerable amount of danger.
We love the Makita Contractor Table Saw for its convenient design and sheer power. The device is powered by a powerful 15 amp motor that enables it to work incredibly well and efficiently. The whole ensemble comes with a superior safety system, a miter gauge, a rip fence, and a 32 inch blade to ensure that you’re prepared to get going and get the job done as soon as you receive the package. We also appreciate the measures taken to protect the blade and machine during transportation like the case that encloses it underneath the table.
Electric brakes in the saw is an important feature as helps the saw in reversing electricity in the motor, thus contributing to a precise cut. It is highly recommended that when you are buying a saw choose the one with on and off switch. The switch should be easily accessible to make work better and more efficient. In addition, the switch should have a cover. This will keep you from accidentally turning the saw on and damaging your work area or cutting yourself.

I see the ovens next to 'fridge. Isn't that a no-no? The heat from the ovens make the 'fridge run to cool more when the ovens are used, upping the electric bill. They are also too far from the center of preparation. I would have put them against the long counter. It would also allow counter space by the fridge to place items when putting them in or taking them out of the 'fridge.
×