Just used this saw for the first time today and I love it. Instructions for putting the stand together were not very clear. There's a lot of very detailed reviews here, so there isn't much I can add that hasn't already been said; but one thing I didn't know until using it is that the rear legs are angled further back than the front ones to provide more stability when pushing stock through the saw. Only used it a few times today, but it was a pleasure to use.
Great match-up and informative… however I too noticed that “No Load” RPMs varied quite a bit from chart to chart – for the same saw. We would expect some variation of 50 RPM as you had mentioned, but not 500 to 800. See that the Hitachi changed from 4400 down to 3700, Delta jumped from 3700 to 4400, Rigid from 3650 to 4350. Upon closer scrutiny… the order of “No Load” RPMs used in first chart may have been used in all subsequent charts. When the “Load” results were ordered by hi-to-low ranking, is it possible that the “No Load” data was not kept with its saw? If so, that changes the %drop results slightly for most RPM No-Load/Load,Speed charts. No too terrible. Lots of data… Good overall presentation though for use to make informed decisions. Thank you!
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
Since this is a high end cabinet table saw, its features are on par with your expectations. This model comes with your choice of cast iron or stamped steel wings. Kickback is also greatly reduced thanks to the quick release riving knife, while the transparent blade guard comes with independent leaves to complete the set of features you’d expect from a Jet Proshop table saw. If you want, you can also get the Jet Proshop table saw in either a thirty inch or a fifty two inch rip capacity. No matter if you’re a professional or if this is the first cabinet table saw you’re planning to get, the 708494K JPS-10TS won’t disappoint. Its rugged build quality and ease of use qualify it as one of the best table saws you’ve ever used.
Designed to be Portable – In case you hadn’t already gathered from the above section, this is a table saw from Bosch that is clearly designed to be portable. If you’re going to need a table saw that can be moved on and off of a worksite with little effort, you’ll definitely find that to be the case with the Bosch 4100-09 and it’s included Gravity Rise Stand.
I have another post for Woodsmith magazines. ShopNotes 2.00 each copyIssue 1 Premiere Issue Shop -- Built Router TableTable Saw AccessoriesTips for Accurate CrosscuttingElu Router ReviewIssue 2Wooden Joiners MalletStorage Bin SystemHand-Cut MortisesRadial Arm Saw FenceIssue 3Handy Tool Carry-AllShop-Built Cling StationPlate Joinery TechniquesAdjustable Grinding JigIssue 4Shop-Built Panel SawThi...
Lowes had a Father’s day sale, on their Kobalt table saw with a folding/rolling stand and was $180.00, with more money off because I signed up for their credit card-so I bought it. It cuts fine, the fence locks on both ends,measurements seem ok, and it unfolds and rolls away very easily-I like it so far. I’m a home owner and I use it sporadically and treat it well, it does not appear to be very robust, so as a day to day, on the job site saw, probably not a good choice. I used to have a Makita table saw, with a terrible fence, unreliable ruler markings, and difficult to use blade guide that interfered with measurements, which you needed to do every time-a terrible saw, very frustrating to use. I have a Makita miter saw and it’s great, but the idea of buying a same brand because I liked one of their other products did not work out.
Contractor saws are a perfect balance between functionality, manoeuvrability and price. These sorts of saws are perfect if you have bigger projects that you’re working on and will stay on site for a few months. This is due to the fact that they are a lot less portable, but that being said they are a great in-between saw as they still have great rip capacity and overall cutting power.
Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
We don’t always post the point totals when we do a shootout like this because it gets complicated – you have to decide what the important features and performance categories are, determine how much weight each one should hold, and then actually hash out the scores with the team. That said, some of these table saws scored so close to each other that I didn’t feel it was fair to just leave it up to the rankings.
The Craftsman Evolv 10 Inch Table Saw is an excellent tool for any craftsman and will change the way you are able to do work The device is fairly easy to transport as it weighs only 50 pounds and can easily be set up on its stand when you reach your designated work area. The saw also comes with a great starter tool kit which includes a miter gauge, a push stick, a stand, a riving knife, and a blade guard fence.
The first contractor saws were made to be portable so they could be taken to job sites. These are also lightweight and priced low enough that the handy homeowner can use them. When purchasing the contractor saw there, you will have to make a few concessions. The table is not made of the cast iron top and the extensions are usually made of stamped medal. It is not made as burly as more costly saws. The motor also hangs off the back, which makes it easier to remove when moving the saw to another job site. Bosch table saws are reported to be one of the best budget saws available.
If you don't need a stand, a benchtop table saw can be an economical and practical choice. The DeWalt DW745 (Est. $300) isn't covered in any professional tests, but it gets excellent reviews from users. This saw is limited somewhat by its small size, as it has only a 20-inch rip capacity and can't make dado cuts. Nonetheless, it earns very high ratings at Amazon with an overall rating of 4.6 stars based on nearly 2,000 reviews. Meanwhile, the more than 600 that weigh in at Home Depot like it even a touch more, granting it a rating of 4.8 stars, with recommendations from 98 percent of users. Owners like its rack-and-pinion fence – the same design found on the larger DeWalt – which they say is accurate and very easy to adjust. Its light, portable size (just 45 pounds) is also a plus. However, like the DeWalt DWE7491RS, it gets a thumbs-down for its flimsy, awkward miter gauge and occasional quality-control problems.
Table saws are pretty complicated pieces of kit and because of that, you can likely imagine that they’re also pretty dangerous at the same time. This is especially the case if you’re using a table saw for the first time. With that in mind, you’ll want to make sure that your table saw features appropriate safety features when buying. There’s nothing worse than falling victim to one of the many accidents that happen every single year as a result of using a table saw.
Replacing the hugely popular outgoing W1824, the W1851 is a brand-new Shop Fox hybrid with the same enclosed cabinet as you’ll find on the W1819 alongside features more in line with a contractor’s saw. We chose to review the W1851 as it’s a more flexible option than the W1819 and appeals to a broader range of woodworkers. We rarely review brand new products but in this case we made an exception… With a brand like Shop Fox, it’s not a case of taking a chance but of betting on a winning team.
It features an 1850W motor which delivers more than enough power for any heavy-duty task and DIY project. Dewalt is well-known for designing quality tools, and they didn’t disappoint with this particular model either. The fence system offers 610mm of rip capacity. As you may assume, even though it’s a portable unit, you can easily cut large pieces of wood to a particular size.
Stands are one of those features where the ends really do justify the means. Some made us wish the manual writers would take a cue from Lego—just make the *@#$! things easy enough for a 7 year old to understand. That aside, SawStop set itself aside brilliantly, taking just 10 minutes to setup. All we had to do was install the wheels and two handles. Even the packaging is designed to make the process easier and the instructions were super-easy to understand. Makita was nearly as simple only requiring us to install the handle and bolt the saw to the stand.
If you’re looking for the perfect cabinet table saw out there, then you should look no further than the SawStop ICS51230-52. This is an industrial grade cabinet saw and is also the highest quality, most powerful and heaviest cabinet saw you can currently get. Its fifty two inch industrial T-glide fence assembly, combined with a 5 HP, 230V single phase motor offers safety, versatility, durability and peace of mind that SawStop is so well known for.
All the articles on this website are short and punchy without much filler, but because there is so much to learn about table saws it will still take you the better part of an afternoon to read through them all. For those who don’t have that kind of time, or those who already know a great deal about table saws, this is the section that will take you to the best table saw for your needs.
×