We’ve approaching the end of the table saw reviews on this page and we’ve selected the GTS1031 10-Inch Portable Jobsite Table Saw from Bosch to conclude those reviews. Our reasoning behind choosing this particular saw is largely because it offers a good all round selection of functionality. As you’ll find over the course of this review, this is a table saw that provides portability, flexibility, power and more. It may not excel in all of those areas but if you’re stuck for choice when it comes to a table saw, this’ll get the job done.

When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.

Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.
Once you’ve gathered your materials, turn your attention to the plate in the middle of the table saw. It surrounds the blade and should have two screws that hold it in place (however some models will have four). Use your screwdriver to undo these screws and set them aside. Then take the plate off and set it to the side as well. Then check to make sure the blade is at its full height by going to the back of your table saw and winding the blade up to full height.
A high performance saw for the most complex of woodworking jobs, the JET XACTASAW Deluxe lives up to even the most demanding of working conditions and craftsmen expectations. Both the trunnion and table are made from heavy duty cast iron to virtually eliminate vibration while cutting, and 29x42 inch workspace allows plenty of room to maneuver large workpieces.
Consequently, they’re going to be a bit heavier than benchtop models. However, their expanding frames mean that you’ll be able to use them even in places where you don’t have access to a table or bench. This is great for construction work, or situations where you’re going to be working outside. This type tends to be a little bit bigger than the benchtop variety, and often has more rip capacity as well.

The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.

Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.
By the late 18th century, a new tool had been created that would eventually have the sawyers out of work: the circular saw. These early rotating saws were powered by a range of different forces, often including running water or wind, and sometimes driven by animal power. By the early 1800s, the sawmill was replacing the saw pit and its hardworking manual sawyers.
For the woodworker who constructs anything from decorative cabinets to handmade boats, the Delta 36-L552 Unisaw is the professional grade cabinet saw that can get the job done. Thanks to its single case trunnion design, the 36-L552 operates consistently with minimal vibration and maximum repeatability of every cut. :Large dual front cranks allow you to dial in your blade height and bevel quickly and easily.
Just used this saw for the first time today and I love it. Instructions for putting the stand together were not very clear. There's a lot of very detailed reviews here, so there isn't much I can add that hasn't already been said; but one thing I didn't know until using it is that the rear legs are angled further back than the front ones to provide more stability when pushing stock through the saw. Only used it a few times today, but it was a pleasure to use.
To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.

Let’s face it: guys get in each other's’ way at a job site. It’s not always easy to find room to work, so portability is a serious advantage when it comes to making the most out of your space. Luckily for the professionals out there — not to mention hobbyists who prefer to move around rather than work in the same spot everyday — RIDGID’s 15-amp table saw comes with a convenient mobile cart for stress-free transportation.


The Delta 36-L552 is a professional grade table saw, built for highly demanding use. You can use it all day everyday and it won’t miss a beat. It’s extremely accurate and will always produce the straightest cuts possible. Because of the high price we would always recommend you really spend some time looking into reviews etc to make sure it’s definitely the right product for you.

The CNS175-TGP36 SawStop is a 10 in. contractor table saw with a 45-degree bevel and a rip capacity of 36.5 in. Other than that, we think this is a pretty cool table saw for a few different reasons. First, the price is about half of all other SawStop table saws, and we know money talks (actually, it yells)! Second, like all other SawStop table saws, it has the integrated flesh sensing technology, so you can be sure you’re going to keep all your digits. Also, it has some pretty impressive power; it’s powered by 15 A motor so you’ll be able to tackle whatever you need. The last of our favorite features is its portability. For being a contractor saw, it’s pretty easy to pack up and move around.


From the triple belt drive system, to the three-HP motor and the large cast iron table and wings, the Shop Fox W18193 s built like a tank. You’re also going to love the T-slot miter gauge that features a fence extension and flip stop, but also a four inch port for dust collection and camlock T-fence. There’s also a twenty nine and a half inch rip capacity.

I just purchased this saw last week. It took several hours to assemble. everything was there and I had no problems putting it together. Not hard but time consuming. The first job was to rework some vertical drawers. It did a good job fence worked great as did the riving knife. Saw was quitter than I expected. overall I am very happy. The only problem was that I had to weight a couple of extra days for delivery due to all parts not arriving at the same time.
You’ll also find that the metal roll cage base will give you extra strength and durability to work with and the rear feet will enable you to adjust the height of the machine should you be faced with the challenge of working on an uneven surface. There’s nothing the DEWALT DW7480 Compact Job-Site Table Saw can’t handle. You’ll quickly be impressed by its ability to tackle any project you throw at it and learn to appreciate it for the great tool that it is.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
One shouldn’t expect a massive amount of storage, but being a table, it does offer some level of free space. In fact, some models even offer space for fences, gauges, blades, and other necessary equipment. Apart from that, you can always keep the necessary tools in the reach of your hands. It will make the process much easier and also a lot quicker.
15 Amp Motor – If there’s one thing that you’ll learn from this website’s table saw reviews, it’s than I order to for a table saw to be effective, it needs to be pretty powerful. With an included 15 amp motor, we can quite comfortably say that this particular product meets that specification. In fact, you should find that the motor is able to easily rip through hardwoods and just about any other type of wood.

Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.
The DEWALT DWE7480 Compact Job-Site Table Saw is obviously a very impressive tool and in our opinion, it’s the best on the market. That’s why we’ve chosen it as our top pick. The design is built with the contractor in mind and helps to ensure that you’ll never have to worry about the machine breaking down on you in the middle of a job or not being able to meet your demands. The saw is fairly light weight (coming in at only 53 pounds) and is powered by an impressive 15 amp motor that has a 20 inch rip capacity.

The first thing people notice about this unit is its design. The rolling stand is specially designed to mitigate the transport of this saw. In simpler words, whenever you need to move it, you can do it by simply rolling the unit on its wheels. One more notable thing is the 2-inch dust collector port. You can easily connect it to a vacuum and extract the dust efficiently and without much hassle.

There are a lot of great table saws on the market, but we’d have to say the best is the DEWALT DW745 Compact Jobsite Table Saw. This design enables you to be flexible with where you set up shop as well as extremely efficient thanks to the innovative technology that was incorporated into the design. Additionally, it has a 15 amp motor and a 20-inch rip capacity that makes it more than capable of taking on any challenge you throw at it.


The first thing people notice about this unit is its design. The rolling stand is specially designed to mitigate the transport of this saw. In simpler words, whenever you need to move it, you can do it by simply rolling the unit on its wheels. One more notable thing is the 2-inch dust collector port. You can easily connect it to a vacuum and extract the dust efficiently and without much hassle.
IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:
I have many bundles of old barn boards for sale. These boards are close to 100 years old if not older and they have all had the square and round nails removed from them. This lumber is completely dry and I am selling them in different sized bundles for those who need different amounts of lumber. The old circle saw marks are clearly visible on each board as seen in the pics. Many people use old ...
In a video review at Tools of the Trade, finish carpenter Jesse Wright finds few negatives and a lot of positives for the DWE7491RS. Wright says this table saw is larger than he normally likes for a portable saw, but its size allows it to tackle tasks that would otherwise be out of reach of a jobsite saw and also makes it very solid and stable. The DWE7491RS also earns a perfect five-star rating from Popular Mechanics, which says it cuts well, is very stable, and has plenty of handy features. The reviewer's only complaint is that the saw is very loud.

Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
You’ll also want to be sure to check that the teeth of the blade are facing towards you since this is the direction that the wood is cut. Once you’ve made sure that the new blade is on properly you can put on the stabilizing parts and nut again. You’ll tighten the nut by putting the spanners on the same way you did before, however, this time you’ll push the spanner in your left hand away from you to tighten the nut instead of towards you.

Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.

It is equipped with plenty of important components and the motor is one of them. It differs from a model to another, but this depends on various circumstances. For example, the smaller models have direct-drive motors that run on 120V circuits. In comparison to all those powerful motors that produce up to 5 hp, the motors designed for smaller units can produce up to 2 hp. This power is enough for cutting thinner material sheets. Keep in mind that the 5hp motors operate on 240V.


The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
At first glance, the Bosch 10-Inch Worksite Table Saw may seem to be nothing exceptional. However, it's powered by the best motor in its class, and it does everything well. True, the motor is a 15 amp unit like the others on our list, but it produces 4 HP where the others produce only 1.5 to 2 HP. This is a noticeable step up in a vital area! The wheeled frame is extremely helpful for moving around your shop or garage, but keep in mind that those tires aren’t heavy-duty; you have to be careful with them on a worksite littered with nails and screws.
The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.
A cabinet table saw is so named because it has an enclosed style base. This saw is the opposite of the contractor saw. Cabinet table saws are designed to be functional and lasting to meet the qualifications that are required by people who work with wood for a living. They are constructed to be more durable than contractor saws. Makita table saw offers many popular options at a very affordable price.
When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.
The DEWALT DW745 is a smaller version of the DEWALT DWE7491RS. It’s still a good saw in its own right. It comes with a 15-amp motor, just like the larger unit, though it can only handle rips of up to 20”. You’ll experience the same power and consequently, the same speed as the larger model, though you can’t cut pieces as large. This model is also meant to be moved, and while it doesn’t have wheels, it has a metal roll cage that will help it survive travel without taking any damage.
The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
The Porter-Cable looks like a beefed-up version of the Craftsman, with the same blade guard and anti-kickback pawls. This is the only saw in our test with a blade-tilting handwheel, which makes it easier to dial in a precise bevel angle. The motor mount and blade controls on this saw are very sturdy, without much play, which translates to a good-quality cut. Extending the fence for a wide rip requires a bit of effort on this saw, since the rails are stiff. All in all, this is a great saw for the price.
×